英文产品说明方案

1、精心整理Spiral chute1、 product descriptionSpiral chute is integrated spiral separator, spiral chute, shaker, centrifugal concentration machine characteristics of the equipment, mining, mineral processing is the best equipment, especially the seaside, riverside, sand beach, the stream of placer mining is

2、 more ideal. The product has the advantages of reasonable structure, simple installation, covers an area of small, simple operation, stable ore beneficiation, clear, large processing capacity, high efficiency enrichment ratio high, high recovery rate, reliable operation characteristics. Have weight

3、light, moisture-proof, rust-proof, corrosion resistance, of the feeding quantity and concentration, particle size, quality of volatility adaptability is strong, no noise.2、 Separation principleSpiral chute is a membrane flow gravity separation equipment, the selection principle is the use of useful

4、minerals and gangue in proportion, particle size, shape differences, in rotating inclined flow by gravity, centrifugal force, hydrodynamic pressure and friction force with different groove face, realize the useful minerals and gangue stratification, branch tape sorting. Heavy, coarse granularity, fa

5、st sedimentation of particles gradually moved towards the spiral groove inner edge, the proportion of small, fine particle size, particle sedimentation slow gradually moved to the spiral groove edge, gradually banding, culminating in the spiral groove end by cutting ore tank is respectively connecte

6、d out, to realize separation.精心整理精心整理3、 ApplicationThe sorting equipment for grain size 0.3-0.02 mm fine iron ore, titanium ore, chromite, pyrite, zircon, monazite, rutile , phosphorus ore, tungsten, tin, B mine of tantalum niobium ore with the difference of specific gravity, and other non-ferrous m

7、etals, rare metals and non-metallic mineral. The sorting process with a stable, easy to control, to allow changes to the mineral concentration range, high enrichment, high recovery rate, small occupation area, little water consumption, simple structure, no need of power, large processing quantity, s

8、imple installation, convenient operation, small investment, quick advantages.4、The method of useThe spiral chute is erected, calibrated vertical line, with metal or wood fixed in position, by the sand pump will ore to spiral top two inlet, adding supplemental water, mineral ore concentration regulat

9、ion paddle, paddle down naturally from high swirl, in rotating inclined flow produces a kind of inertial centrifugal force, with ore proportion, particle size, shape differences, swirl through the action of gravity and centrifugal force, will be mine and sand separating, concentrate into the concent

10、rate pipe connected with a hopper, tailings into tailing bucket a pipeline is connected to a sand pool, then the pump discharge, finished processing the whole process.5、Structure and technical parameterMainly by the ore separator, cross, to mine groove, helical groove, cutting trough, pick ore bucke

11、t and slot pillar of seven components. The helical groove is spiral chute of the main components, each spiral chute is 2 - 4 head spiral groove, each精心整理head spiral groove is composed of 5 spiral plates (according to mineral properties and beneficiation process need, after tests also consider 4 circ

12、les, in order to reduce the equipment height) spiral plate by bolts are fixed together, spiral sheet is made of glass fiber reinforced plastic (FRP) made, light weight, anti-corrosion, moisture-proof, anti deformation and strength.6、InstallationSpiral chute installation procedures and requirements:1

13、) First check the glass steel spiral slice quality (especially the work surface quality), size and shape to meet the requirements for assembly2) Screw plate connecting bolt hole by the general factory in advance with a drill. If the manufacturer has no processing is required, according to the same t

14、emplate drilling, in order to ensure good interchangeability.3) Bolt the five coil sheet are connected into a group of spiral groove, level set, two adjacent flange connection within the surface smooth transition is connected, special attention should be paid on the surface may not be lower than the

15、 corresponding lower sheet surface. Along the diameter direction.(the slot width direction) to edge alignment as the standard, do not allow plate rim inside, so the installation is intended to prevent the occurrence of ore fluid splash. Joint gap, with putty.4) The coupled five of a group of four (o

16、r two or three) spiral groove rotating together into a desired shape, distribution.5) The four roots (three) column is respectively arranged in four (or three, two) spiral groove, bolt the spiral groove and the pillar is fixed, then install the cross 精心整理精心整理(tripod), so that each spiral along the p

17、ark are cloth, then all bolts. After installation, spiral plate to maintain the natural shape, with no obvious variant.6) Would give mine groove and product interception groove are respectively arranged in the spiral groove of the head end and the tail end to ensure that the connection of close wate

18、r leakage. If there is a gap, by coating sealing. To ensure the smooth transition of groove surface.7) To mine even divider and product assemble bucket and the slot bracket is not connected, free placed on the bracket, the installation should pay attention to in the chart are position. Each row of t

19、ube to distributor are respectively aligned with corresponding to the ore tank.6-S shaking table1、ApplicationThe 6-S shaking table is one of the main equipment of gravity concentration, it is widely used in separating tungsten, tin, tantalum, niobium, gold and other rare metals and precious metal or

20、e. Can be used for roughing, concentration, scavenging different operations, separating coarse sand (2-0.5mm) (0.5-0.074mm), fine sand, clay (- 0.074) of different grain grade It can also be used to separate iron, manganese ore and coal. When processing tungsten, tin ore, the table effective recycli

21、ng particle size range for the 2-0.22 mm.2、PerformanceThe shaking table is in the beneficiation process is complex a tilt bed plane, ore particle swarm from the bed surface angle to the trough into, at the same time by lateral flushing water supply to the water tank, and the mineral particles in gra

22、vity,精心整理精心整理lateral flow momentum, bed reciprocating asymmetric motion produced by the inertia and friction effects next, according to the proportion and hierarchical granularity, and along the bed surface for longitudinal movement along the inclined bed surface and transverse motion. Therefore, sp

23、ecific gravity and particle size of different mineral particles along the direction of movement of the respective gradually by the A side to side B fan-shaped shed, concentrate and tailings from the end side of the discharging end is divided into different, concentrate, middling and tailings.6-s has

24、 a double high rich ore ratio, high separation efficiency, safeguards easily, convenient for adjusting the stroke. In change cross fall and stroke is still maintain the surface of bed movement balance, the spring is placed in the box body, compact structure, and can in turn draw final concentrate an

25、d tailings.3、Classification1、 According to the different position of ore, shaker can be divided into right and left type cradle type cradle two forms. The right type cradle for the ore location for the rocking mechanism is on the right side, left type cradle to mine is located in the left.2、 6-S sha

26、ker can be divided into fixed shaking table , channel bar shaking table, big channel steel shaking table.3、 According to the concentration particle size, divided into coarse sand table, sand table and slimmer three.4、 StructureThis table is mainly composed of a bed head, motor, adjustable slope, the

27、 bed surface, mine shafts, sink, and reflex and lubrication system of eight components.精心整理精心整理The surface of bed longitudinal reciprocating motion through a crank connecting rod type driving mechanism to realize. The electric motor through the belt drive to make the big belt wheel drives the cranks

28、haft to rotate, the rocker made subsequently moves up and down, rocker downwards, elbow board drive rear axle and the reciprocating rod moves backwards, the spring being compressed. The bed surface is through linkage seat and a reciprocating lever connected, so this is also so the bed surface for ba

29、ckward movement, when the rocker upward movement, due to the tension spring drive, the bed surface will move forward.5、 Specification6、 Installation and cautions1) On the basis of drawing, reserved anchor screw holes or pouring good foundation plate, expansion, the construction of concrete foundatio

30、n.2) The shaker frame placed on the basis, make each place, calibration and pad frame bea 3) The Department of anchor screws tightening, the cradle is fixed on the basis of.4) Mounted on the drag device, bed surface, bedside and bed and the bed surface connec attention should be to the front to beds

31、ide flywheel.5) Connect the switch of the motor insurance, check whether the motor leakage, and then wire.6) The bed surface is not strong beat, collision; not in high temperature and heavy pressu pollution and sun and rain, prevent degeneration.7) After the installation, a detailed examination, the

32、 confirmation, removal of equipment a surrounding sundries.8) Roller with 10-20 G oil, not to splash as well. The seat sliding rack injection oil to drown bearing and the lower bearing contact fit; lever type rocking frame bearing has been manufa good lithium grease.9) Put the washing water air mach

33、ine test machine operation, observation and examinati and operation, the moving parts are not loose fever or unusual sounds.10) Empty test machine to normal, can load test machine, according to the selected minerals and adjustment of the stroke, stroke, springs, bed longitudinal slope and transverse

34、 slope achieve the optimal separation effect. After normal cleaning, it can be put into production7、 operation and maintenance1) Feeding volume and concentration of proper, if give mine too large volume, concentratio rate.2) The bed surface transverse slope large, flushing water should be smaller; s

35、lope is sma water shall be selected.3) Stroke and frequency of stroke should be adjusted properly. Stroke is too small too big, af stratification. To change the diameter of a motor belt pulley, adjustable stroke Adjusting spi set of eccentric combination, can have different stroke, Permanent magneti

36、c separator1、Range of applicationThe series of magnetic separator for sorting magnetic minerals, non-metallic materials and waste materials deironing. Such as: reduction of titanium magnetite, iron ore smelting in front of the purifying selection, ceramic clay, feldspar, quartz, iron ore, coal and o

37、ther materials in addition to iron.2、The structure and working principle精心整理精心整理CT series cylinder type permanent magnetic separator, drum body and a groove near the magnetic system parts are made of non-magnetic material of stainless steel, cylinder end cap cast in aluminum, and other ordinary stee

38、l production. Equipment structure is composed of a machine frame, body, a cylinder, a magnetic system, power plant, feed, water, discharging part. The groove body and cylinder distance according to the mineral separation of lifting adjustment, magnetic angle can be adjusted at.(no water supply devic

39、e of dry type)1) CTC dry magnetic separator: dry aggregate from the hopper into the cylinder directly to the upper or lower portion of the drum, magnetic mineral particles are magnetic in the surface of the drum, winding drum rotates to the edges of the natural unload magnetic system. Non magnetic m

40、ineral particles by the action of gravity and centrifugal force and magnetic products into different ore bucket. Magnetic products magnetic products and is arranged in the middle of ore isolation plate, according to the mineral material selected to adjust the situation.2) CTB semi-counter current ma

41、gnetic separator magnetic lines in the lower part of drum. Pulp from the tank into the lower part of the lower roller, non-magnetic minerals in the direction of movement and the rotation of the drum in the opposite direction, magnetic minerals moving direction and rollers rotate in the same directio

42、n. The lower part of the spray pipe body is inserted, is used to adjust the separating operation of slurry concentration, the slurry dispersed into loosely suspended state into the separation space. The magnetic particles in the magnetic system of magnetic field force, is absorbed on the surface of

43、the roller, roller together with the upwardly mobile. In the moving process, because the magnetic精心整理lines of alternating polarity, so that the magnetic mineral particles into a chain of turning, in the turning process, the inclusions in the magnetic mineral particles in non magnetic mineral impurit

44、ies is cleared, so as to effectively improve the purpose of magnetic products. Semi countercurrent magnetic separator for mineral slurry concentration and granularity is sensitive to change, when the concentration is too large or grain through the metropolitan influence index of mineral processing.3

45、) CTS downstream separator: feeding direction and the direction of rotation of the drum or magnetic mineral moving direction. The pulp comprises feeding bucket directly into the cylinder below the magnetic system, non magnetic particle and magnetic weak mineral particles from beneath the tank bottom

46、 roller two and the gap between the discharge, magnetic mineral particles are sucked on the surface of the cylinder, with the roller to rotate together to the magnetic system edge discharge, magnetic ore discharging position is provided with a discharging water pipe. Downstream separator on mineral

47、beneficiation of wide adaptability, easy separating space is smooth without obstruction, particularly applicable to contain magnetic minerals a larger proportion of the magnetic separation process.4) CTN upstream separator: feeding direction and drum rotation direction or magnetic material moves in

48、the opposite direction. The pulp comprises feeding bucket directly into the cylinder below the magnetic system, non magnetic particle and magnetic weak mineral particles from tank bottom hole discharging tailings, magnetic mineral particles with the roller against the feed direction to give mine is

49、discharged to the magnetic ore groove, for the reduction of magnetic products with non-magnetic mineral, in magnetic ore unloading mounted before the cleaning精心整理water pipe, magnetic ore discharging position is provided with a discharging flushing pipe. Countercurrent separation machine due to the m

50、agnetic ore discharge end distance to mine mouth close, magnetic turning effect is poor, so the magnetic ore grade to be slightly lower, but its tailings ore export far away from the mouth, the pulp after longer divided districts, increases the magnetic mineral particles are magnetically attracted t

51、o opportunity, all the magnetic separator magnetic product recovery rate is quite high, counter flow type magnetic separator suitable for only require nonmagnetic product precision of various minerals.3、 Specification4、 Installation and use1) At first machine installed must check the transport loadi

52、ng and unloading is loose, damaged.2) The horizontal position, implement, conventionally grounded.3) Check, adjust the magnetic system to the fixed position processing and working distance.4) Before the first test machine, drum empty running again, water supply, feeding, everything is normal, and th

53、en evenly feeding load test machine. According to the material separation requirements for adjusting the output, quality, recovery rate.5、 Preventive maintenance1) Removing: drum removable from the frame, standing on a stable level of supporting frame. Have a head driving device placed below.2) When

54、 hoisting drum magnetic parts do not close to the strong magnetic tool or magnetic materials.精心整理3) Will fixed aluminum cover fastening screw removal. The 4 screw mount aluminum end cover removing hole. Parallel to the rotating 4 pearl will cover up after unloading, and then remove the lower end cov

55、er fastening screw, can come up with a stainless steel cylinder. Aluminum cover middle small iron cover for the bearing cover and cover solid screw.4) The assembly must be completely to the magnetic surface and stainless steel inner cylinder of clean.5) Transmission gears, bearings, reducer shall be

56、 regularly maintained and filling calcium base grease lubricating oil.6、 Cautions1) Strong magnetic tools, articles shall not be close to the magnetic system.2) Do not beat, collision stainless steel tube.3) Super size mineral, not into the machine, so as not to get stuck or wear of stainless steel

57、copper cylinder.4) Abnormal sound, should be excluded.Ball mill1、Purpose and use scopeBall mill is the material being broken, and then smash the key equipment. Mill widely used in cement, silicate products, new building materials, refractory materials, fertilizer, black and non-ferrous metal process

58、ing and glass ceramic production industry, for all kinds of ores and other materials may be grinding of dry or wet grinding.2、Working principle精心整理This machine is a horizontal cylinder rotating device, outer gear transmission, the warehouse has stepped lining board or corrugated liner, built in diff

59、erent specifications of steel balls, the rotation of the cylinder to generate centrifugal force will bring the steel ball to a certain height after the fall, the material produces severe impact and abrasive. Powder through the discharge grate discharge, then finish grinding operation.3、StructureThe equipment consists of feeding, discharging part, turning p