BR盐雾试验机英文版说明书

1、Salt Water Spray Test ChamberOperating manualI. Structure synopsis1. In test chamberA Spraying of water towerThe internal form experimental nozzle puts on nozzle in, atomizesafter treads the tube the guidance, again passes through the cone-shape diffuserto disperse to the test chamber in.B Atomizati

2、on adjusting deviceThe adjustment atomization quantity size, moves high when atomizesthe quantity to increase, lowers time reducesC Salt water preparation troughIs located the spraying of water the tower base, the salt water isafter the salt water supplemented the barrel pours into the preheating tr

3、ough, thepreheating trough has the switch, may the automatic control water level, in thetrough the base have the clean to use draining water exportation, by plug controls.D Collects the cupAbout nearby two respectively has, uses for to collect the blowout the mist, theprocess leads the pipe flow to

4、in the test chamber outside graduated cylinder.E Humidity cupThe L model humidity cup is with the humidity fashionable clothingwater vessel.F Puts the thing the rackThe focus point is important do not have to surpass 2KG, if the disperser layingaside may put in 10KG about, both sides the rack has tw

5、o rows of V shape hole, isuses for to lay aside the glass rod and vertical direction the minute 30, 45 angles uses.G Heat installationTest chamber control temperature installment.H Filtrating equipmentUses for to filter in the salt water the impurity.I Isolates the water troughThe isolation temperat

6、ure prevented the smog divulgesJ Heats up the water troughIn the test chamber base, installs the water to heat up causes the test chambertemperature balance, the function is heats up with the heat preservation.2 Test chamber exteriorK Dry bulb temperature ideaTests in the laboratory the temperatureL

7、 Wet-bulb thermometerTests in the laboratory the humidityM Counts graduated cylinderThe collection each time experiments atomization quantity.N Saturated spatial air drumLays aside in the control box the base, the function lies in to the air adds thetemperature and the humidity, then delivers in the

8、 test chamber the nozzle.O Salt water supplement barrelIn automatic supplement salt water preheating trough salt waterP Experimental coverThe drift angle 100 angles, use in to cover in the test chamber place above.Q Air ventOutside the caliber pipeline by 11/2 , discharges the mist the pipe to recei

9、ve,causes the mist to discharge.R Draining water exportationOutside the caliber pipeline by 1/2 , discharges the water receives the drain,causes the waste water to discharge from here.S Water entranceThe caliber pipeline by 1/2 , the connection adds the water pipeto the preheating water trough and t

10、he saturated spatial air drumT Supplements the salt water the barrel water level measuring appliance U The airreduced pressure filter, the machine works above for 24 hours, underneath the filterhas draining water the exportation, gently upwardly presses the draining waterexportation, or always barom

11、etric pressure closure.3. Control system(1) test chamber temperature controller pneumatic control test chamber temperature,according to standard temperature hypothesis, saltwater testing method 35C , anti-corrosive testing method 50C .(2) testchamber water level insufficient - like test chamber wate

12、r levelinsufficient, the indicating lamp is bright, also the electromagnetism valve circuit,automatically enters the water until the full water level namely to extinguish.(3) normal like test chamber and saturation tank water levelinsufficient, the indicating lamp is bright, expression normal state.

13、(4) saturation tank water level insufficient like saturated spatial airdrum water level insufficient, the indicating lamp is bright, alsothe electromagnetism valve circuit, automatically enters the water until the fullwater level namely to extinguish.(5) saturated spatial air drum temperature contro

14、ller control saturated spatial air drumtemperature general temperature hypothesis, salt water testing method 47C ,anti-corrosive testing method 63C .(6) pressure gauge this table demonstrated the pressure which thepressure is the air heats up after the saturated spatial air drum, transmits whenspray

15、 nozzle achieved.(7) the timer may wilfully establish the laboratory to need the time,after had finished auto-stop.(8) pressure-regulating valve this valve is the air pressure whenoutdoes lowly, borrows presses the table to demonstrate adjusts. (Test condition1kg)(9) accumulates when straight reads

16、type 0 to be possible to instructaccumulation the experimental time.(10) the power switch controls the entire machine total power source.(11) the console switch controls the test chamber to heat up the troughand the saturation tank spatial air drum electricity heat pipe power source.(12) atomizes th

17、e switch control compressed air to enter the test chamber to causethe spray nozzle atomization.(13) timer switch control timer power source.(14) the defogging switch uses to control the test chamber to remove the mist.IIInstalls the notice and the matters needing attention:1. The power source is: AC

18、 1 巾 220V 20A 50Hz2.The machine lays aside in behind to wall approximately 40cm, about two sidesmust reserve the service space.3. Outside the machine pessimistic electric wire is the total power line, the power lineplease again installs a non- melt silk switch or the knife switch. 6 meter fast airco

19、mpression pipe joint to is spatial (U).4. The water entrance may use PVC 1/2 hard tube or the soft pipe joint running watersource.Draining water place mayuse PVC1/2 hard tube or the hose discharges, must payattention to the water pipe to be supposed downward, also cannot be higher thanthe exhaust pi

20、pe.The air vent must with PVC 11/2 hose, extend to outside discharges, must payattention to the exhaust pipe the installment, may parallel be upward by themachine or be parallel to under. (Upward when must not affect (when transparentexperimental cover opens) above installs the PVChard tube, margin

21、place does nothave residual to model Rubber dust, otherwise electromagnetism valve is easy toblock, creates not good phenomenon).5. The machine installment position, please avoid the sunlight direct radiation, inorder to avoid condition of the influence test.6. The machine installment position, shou

22、ld not approach other electric applianceequipment as far as possible or be flammable, in order to avoid danger.7. This machine is the PVC revertex makes, please do not make an effortto collide, in order to avoid cracks. The application temperature please do notsurpass the experimental standard scope

23、, in order to avoid because of hot hasdistorted or the breakdown.8. Hypothesis experiment time 0.9. Presses down the atomization to press a keyA. the valve which lets in air the air compressor front to openB. to transfer to the air compressor pressure relief valve pressure of2the 23kg/cm (clockwise

24、increase, anti-clockwise reduction).2C. transfers to the pressure-regulating valve pressure of the 1kg/ cm, its pressuremay know by the pressure gauge. (Clockwise increase, anti-clockwisereduction).10. Presses down the time pressed key, then may depend on the hypothesis time, thetime finished the au

25、tomatic power failure.11. The experiment finished, according to order each switch closure.12. In the experiment like has exceptionally, please refers to the functionexceptionally to judge table processing.III. The operation explained1. Mixes the experimental solutionTo mix the method: The 9.5L pure

26、distilled water, joins 500gNaCl, performs to stir,causes its full dissolution. (this time salt water density is 5%)2. Pours into the salt water fluid note entrance the liquid medicines, causes themedicine current of water to the salt water preheating trough.3. The cup watering, the wet-bulb thermome

27、ter will cover the gauze, the gauzeterminal is setting in the cup.4. The laying aside previews or the test specimen in sets at the thingon * ornaments angle to depend on needs the standing operating procedure todecorate5. The hypothesis experiment temperature* depends on must experiment the standing

28、 operating procedure to decorateA The salt water testi ng method: Test chamber temperature 35csaturated spatial air drums temperatures 47cB Corrosion testing method: The test chamber temperature 50csaturated spatial air drums temperatures 63c6. Press down the power source, operates the pressed key,

29、first pre- warm, uses for toarrive the hypothesis temperature.* The attention will have to experiment the lid to cover. (For examplewater level is in sufficie nt in dicat ing lamp is bright, the n will beable automatic control supplement water level, will shine until normal in dicat inglamp, will be

30、 allowed to operate).7. The hypothesis experime nt time8. Presses down the time, the air compressor two pressed keys carries on theexperime nt.* Presses down the atomization pressed key if does not have the gas toleave, looks up behi nd the air compressor the switch admissi on valve and theadjusti n

31、g valve whether do ope n.* In the test chamber like must regarding as, press down removes the mist switchoutside, causes the mist rapidly to discharge.9. The experime nt fini shed, accord ing to order each switch closure.* Like will experiment the time-gap to the next time long, will ask YuCici to e

32、xperiment finished, cleans the test chamber interior to maintain the machine to be clea nVI. Judgme nt and address whe n fun cti on out of fun cti on:Situati onReasonAddressThe temperature of the labcan t reach the sett ingThe temperature set by the labthermometer is too lowThe safe and protect ion

33、switch ofthe lab is too lowHeati ng system out of workFeb-Mag netic con tact out ofwork Control machine out of workLet the thermometer set what it needsLet the safe and protecti on switchset what it n eedsYou can call the warranty personnelfor help by the wire map or call usfor addressThe temperatur

34、e of thesaturati onbarrelscan treachthesett ingThe temperature set by thesaturati onbarrelsthermometer is too lowThe safe and protect ion switch ofthe saturation barrels is too lowHeati ng system out of workFeb-Mag neticcon tact outof workControl machine out of workLet the thermometer set what it ne

35、edsLet the safe and protecti on switchset what it n eedsYou can call the warranty personnelfor help by the wire map or call usfor addressSpray(fog.)volume isno enoughThe spray (fog.) regulator putstoo lowThe glass filter which in thepre-heat box is plugSetting pressure is too lowRise thespray(fog.)r

36、egulatorClear the glass filterAdjust the press-valves to21kg/cmor adjustthedecompress-valves to 2 3 kg/cm2Con diti onReasonProcess ingWhen is unable thethe air compressor hasturnsontheairatomizati onnot revolvedcompressor pressedkeythepressureisadjuststhein sufficie ntpressure-regulat ing2valve gate

37、 1kg/cmthethesole noidvalvepressurebreakdow nin forms this compa ny tothe pressure measuri ngprocess in formsthisapplia nee breakdow n themagn etic con tactorcompa ny to processbreakdow nin forms this compa ny tothe spray nozzle blocksprocessdisma ntles theno zzleclea nsIn the experime ntthe total power s