注塑常用术语英文表达

1、1。雾气 Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气 Gas Trap Effect4。银丝纹 Sliver Marks5。结合线 Weld Line6。水波痕 Water Wave Effect7。黑点 Dark Sport8 .顶出印 Visible Ejector Marks9 .变形 Deformation During Demolding10。填充不足 Short Filling11。冷料流痕 Cold Slug12。进胶口 点不良 Dull Spots Near The Sprue13.喷射痕 Jetting14。表面起层 Fla

2、king Of The Surface Layer15。浮泡 Entrapped Air16.过热变色 Burnt Streaks17。龟裂 Stress Crack18。缩水痕 Sink Marks19.真空气泡 Density Bubble20。披锋 Flash21 .擦伤Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大 Over dimension23 尺寸过小 Under dimension24 翘曲 Warpage/warped25 收缩 Shrinkage/shrink26 缩影

3、Sink marks27 打不满 Short shot/short molding塑料模具 mould of plastics 注塑模具 injection mould冲压模具die模架 mould base定模座板 Top clamping plateTop plateFixed clamp plate 水 口 推板 stripper plateA 板 A plateB 板 B plate 支承板 support plate 方铁 spacer plate 底针板 ejector plate 面针板 ejector retainer plate 回针 Return pin导柱 Guide p

4、in有托导套 Shoulder Guide bush直导套 Straight Guide bush动模座板 Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板 core-retainer plate凸模固定板 punch-retainer plate顶针 ejector pin单腔模具 single cavity mould多腔模具 multi-cavity mould多浇口 multi gating浇口 gate缺料 starving排气 breathing光泽gloss合模力 mould clamping

5、force锁模力 mould locking force挤出 extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件 movable insert起垩 chalking浇注系统feed system主流道 sprue分流道runner浇口 gate直浇口 direct gate , sprue gate轮辐浇口 spoke gate , spider gate点浇口 pin-point gate测浇 口 edge gate潜伏浇口 submarine gate , tunnel gate料穴 cold slug well浇口套

6、 sprue bush流道板 runner plate排飞槽vent分型线（面）parting line定模 stationary mould , Fixed mould动模 movable mould , movable half 上模 upper mould, upper half下模 lower mould , lower half型腔cavity凹模 cavity plate , cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销 angle pin, finger cam滑块slide滑块导板 slide guide strip楔紧块

7、heel block, wedge lock拉料杆 sprue puller定位环 locating ring冷去口通 cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具 hotrunner mould绝热流道模 insulated runner mould熔合纹 weld line (flow line )三板式模具 three plate mould脱模 ejection换模月空模具 interchangeable cavity mould脱模齐U release agent注射能力shot capacity注射速率 injection rate注射压力 injection pressure差色齐U colorant保压时间holdup time闭模时间 closing time定型装置sizing system阴模 female mould , cavity block阳模 male mould电加工设备 Electron Discharge Machining数控加工中心 CNC machine center万能铁床 Universal milling machine卧式包床 Horizontal planer车床 Engine lathe平面磨床 Surface grinding mac