EL屏幕软件升级

1、1会计学EL屏幕软件升级屏幕软件升级Seite 2Training overview :Interface structureHow to Start-up the new components 1. OP1000 (applicationsoftware) 2. DIG000 (applicationsoftware) Seite 3EthernetCan Group 07with other sensorsOL80FR.Fx.FE.Network 1DIG000 Software: Pc0016-8003M +Application software xxx.xxxPossible com

2、municationsMitshubishiSiemensBeckhoff.Standard Ethernet: Software Pc0016-8002M Ethernet Ip Software Pc0016-8010M EGDOP 1000CPUI / OI / OI / OI / OKunden SPS / IPCPLCEthernet SwitchX8; 24V DC (z.B. 326491) Can Group 07with other sensorsOL80FR.Fx.FE.Network 2DIG000DIG000Seite 41.Change the PC-Ethernet

3、 settings2.Download Software to the DIG0003.Set the ip-address of the OP1000 Panel4.Download software to the OP1000 Panel5.Download PLC-software in DIG0006.Check the Dongle Value EK 5101 Seite 51. Change the PC-Ethernet settingsTo get a ethernet connection between two devices you need a few conditio

4、nsA ethernet connection exists of following parts. ip-address010.006.002.003Netmask255.255.000.000Device 1ip-address010.006.002.124Netmask255.255.000.000Device 2A connection is only possible if the blue numbers are the sameSeite 61. Change the Pc-Ethernet settingsOpen the networksetting in your PC10

5、 . 6 . 2 . 4To get a connection to the devicesSet the ip-address of the pc-ethernet cardAttention:If you connect a Pc direkt to a device you Need a cross-cabel.If the Pc and the devices are connected Over a ethernet switch you need a patch cabel.Seite 71. Change the Pc-Ethernet settingsPut in the ip

6、-addressOf the DiG000Open javacanmonpress the Add buttonSeite 81. Change the Pc-Ethernet settingsIf you dont know the ethernet address you have to set or read the ip-address1. With a seriell connection2. with Javacanmon Can-Dongle. recommendedSeite 91. Change the Pc-Ethernet settingsChange to servic

7、e,Select the Service functionSet TcpIp Addr andPress the buttonSetSeite 101. Change the Pc-Ethernet settingsConnect the hardware to the PC.Ethernet (Cross cabel) z.B. 328927 (10m) Seite 111. Change the Pc-Ethernet settingsHere you see theActive connectionTo the hardwareSeite 122. Download software t

8、o the DIG000 or DM4000Basicsoftware: PC0016-8008M_ZBBasis MasterLogic: PC0016-8003M_ZDEhternet/IP: PC0016-8002M_ZCPress the Download buttonChange to SoftwareSeite 132. Download software to the DIG000 or DM4000Select the software and press openDownload is onlyPossible over Ethernet Seite 143. Set the

9、 Ip-address of the OP1000 PanelIf you press with your fingers at the same time these points for At least 2s. The panel switch to the setup modeSeite 15Change with the keyboard to the function CONFIG and press ENTERThe panel switch to the configuration mode3. Set the ip-address of the PanelENTERSeite

10、 163. Set the ip-address of the PanelIn the configuration mode You can see some informations.FirmwareNetworksettingsTimesettingskeyboardSeite 173. Set the ip-address of the PanelIn the configuration mode You can see some informations.To change the Networksettings Touch this area.Seite 183. Set the i

11、p-address of the PanelSet the new ip-Address And press EnterSet the netmask and pressEnterSet the Gateway and pressEnterPress 2 time Enter and the New settings change.Seite 193. Set the ip-address of the PanelConnect the OP1000 to the PC.Ethernet (Cross cabel) z.B. 328927 (10m) Seite 20You need the

12、software UniDataexchanger from exor. Each application need a special panelsoftware named Project.romSelect Download ProjectSelect the Firmeware4. Download software to the panel Seite 214. Download software to the panel Open the optionCommunication To select the ip-addressOf the panel Seite 22Select

13、the OP1000Here you have to be set the ip-address of the Panel. The Panel must connected to the PCYou also can try the ButtonPick UniOP. All connected Panels are showed and you Can select the needed panelIf no panel is showed in the Pick UniOP you have no connection4. Download software to the panel S

14、eite 23Befor you can download a programm the panel have to be switched to the configuration mode. Select Commands Switch to configuation mode,And wait until done. The panel shows a black screen with severalSettings of the panel. After that you can start withThe download of the software.4. Download s

15、oftware to the panel Seite 24Press the Start button and select the application.rom file. After Open the download starts4. Download software to the panel Seite 25You see the state of the download4. Download software to the panel Seite 26After successful download you have to switch the panal back to t

16、he operation mode. You also can switch off the power supply of the panel.4. Download software to the panel Seite 274. Download software to the panel The panel is only running if you have a masterLogic software in a DIG000 or aDM4000 and is connected to a MasterLogicStartwindow ifNot connectedSeite 2

17、8Basicsoftware: PC0016-8008M_ZCBasis MasterLogic: PC0016-8003M_ZDEhternet/IP: PC0016-8002M_ZCInfos about the software of the masterLogic software5. Download masterLogic-software to the DIG000Select the PLC barSeite 29application Softplc: Softinfo of the applicationsoftware5. Download MasterLogic-sof

18、tware to the DIG000Seite 302. Select software.PRG1. Press download button3. Start download5. Download plc-software to the DIG000Seite 316. Check the Dongle value from the EK 5101 on a DIG000You can read the dongle if youPress the button CheckSelect the hardware.DiG000 DM4000DO81Seite 326. Check the Dongle value from the EK 5101 on a DIG000The actuall connected dongleHas the dongle value 6 + MasterLogic softwareSeite 33Seit