SC200(200TD)施工升降机使用说明书

1、SC200/200TD 施工升降机施工升降机Builders Hoist使用说明书使用说明书Instruction manual成都恩利斯机械设备有限公司Chengdu Earnest Machinery Equipment Co.,Ltd2015030目录目录 CATALOGUE0 前言 PREFACE.30.1 设备信息 MACHINE INFORMATION.30.2 正确使用本说明书 CORRECTLY USING THE MANUAL.30.3 安全提示及安全标识 SAFTY TIP AND MARK.30.4 安全风险提示 GENERAL INDICATION ABOUT SAFE

2、TY.30.5 保修说明 WARRANTY DESCRIPTION.50.6 免责声明 DISCLAIMERS.61 产品概述 OUTLINE AND FEATURE. 71.1 升降机型号说明 MODEL DESCRIPTION.71.2 升降机性能参数 PERFORMANCE PARAMETERS.71.3 升降机结构综述 SUMMARY OF THE STRUCTURE.81.4 安全装置 SAFTY DEVICE.132 基 础 FOUNDATION.162.1 基础载荷计算 FOUNDATION LOAD CALCULATION.162.2 基础技术要求 FOUNDATION REQ

3、UIREMENTS.162.3 基础图 FOUNDATION DRAWING.173 附墙装置 MAST-TIE.183.1 附墙架作用于建筑物上力 FORCE ACTING UPON THE BUILDING.183.2 附墙架结构 MAST-TIE STRUCTURE.183.3 附墙座联接方式 CONNECTION WAY OF MAST-TIE.193.4 附墙架间距 INTERVAL BETWEEN MAST-TIE.194 升降机操作 OPERATIION.204.1 操作安全规程 SAFETY REGULATIONS FOR OPERATION.204.2 司机室操作面板及笼顶操

4、作盒 RUNNING IN DRIVER CABIN OR ON TOP.214.3 操作方法 METHOD OF OPERATION.224.4 紧急处置 EMERGENCY ACTION.235 坠落试验 DROP TEST.255.1 适用范围 SCOPE OF APPLICATION.255.2 坠落试验方法 METHOD OF DROP TEST.256 防坠安全器及重量限制器 ANTI-FALLING SAFTY DEVICE AND LOAD LIMITER.276.1 防坠安全器使用要求 SAFTY DEVICE OPERATION REQUIREMENT.276.2 防坠安全

5、器调整 ADJUSTING SAFETY DEVICE.276.3 重量限制器 LOAD LIMITER.307 定期检查 REGULAR INSPECTION.317.1 每天检查 INSPECTION EVERYDAY.3117.2 每周检查 INSPECTION WEEKLY.317.3 季度检查 INSPECTION QUARTERLY.327.4 年检 CHECK YEARLY.337.5 齿轮的检测 CHECK GEAR.337.6 齿条的检测 CHECK THE RACK.338 润滑 LUBRICATION.349 施工升降机的安装 INSTALLATION OF HOIST.

6、359.1 施工升降机安装前的准备 PREPARATION FOR INSTALLATION.359.2 需用户自备的零部件 USER - OWNED PARTS.369.3 安装安全规程 SAFETY REGULATIONS FOR INSTALLING.369.4 外笼与吊笼的安装 INSTALLING THE ENCLOSURE.379.5 电气连接与调整 ELECTRICAL CONNECTION.429.6 外笼吊笼安装后的调整 ADJUSTMENT AFTER INSTALLATION.439.7 导轨架的安装 MAST SECTIONS INSTALLATION.439.8 附墙

7、架的安装 MAST-TIE INSTALLATION.459.9 电缆桶及其安装 CABLE BARREL INSTALLATION.469.10 电缆滑车的安装 INSTALLATION OF THE CABLE CAR.479.11 限位开关安装 INSTALLING POSITION LIMIT SWITCH.499.12 层门安装 INSTALLING LANDING DOORS.5010 故障检查 TROUBLESHOOTING.5110.1 常见电气故障 COMMON ELECTRICAL FAILURES.5110.2 常见机械故障 COMMON MECHANICAL FAILU

8、RES.5111 易损件更换 WEARING PARTS REPLACEMENT.5311.1 齿轮更换 GEAR REPLACEMENT.5311.2 齿条更换 RACK REPLACEMENT.5311.3 导轮更换 BACK ROLLER REPLACEMEN T.5411.4 滚轮更换 ROLLER REPLACEMENT.5411.5 限速器更换 SAFTY DEVICE REPLACEMENT.5511.6 减速器及电机更换 GEARBOX AND MOTOR REPLACEMENT.5611.7 电机制动器块更换 MOTOR BRAKE BLOCK REPLACEMENT.561

9、2 维修安全卡具及维修门 MAINTENANCE FIXTURES AND GATE.5912.1 维修门 MAINTENANCE GATE.5912.2 安全卡具 SECURE FIXTURES.5913 附录 APPENDIX.6113.1 易损件明细表 SPARE PARTS LIST.6113.2 电气原理图 ELECTRICAL CIRCUIT DRAWING.6120 0 前言前言 Preface0.10.1 设备信息设备信息0.1.1 设备名称:施工升降机0.1.2 设备编号： 0.1.3 制造商：成都恩利斯机械设备有限公司0.1.4 出厂日期： 0.1Machine infor

10、mation0.1.1Machine name: Builders hoist0.1.21Machine No.: 0.1.3Manufaturer :EARNEST0.1.4Production date: 0.20.2 正确使用本说明书正确使用本说明书首先感谢您使用成都恩利斯机械设备有限公司生产的施工升降机。在安装、使用施工升降机前，必须认真详细阅读本说明书，以确保安全。该说明书应随机携带，以备查阅。任何不符合说明书要求的安装、操作或维修都可能引发意外或安全风险。本说明书中的图例仅为了说明，可能与您订购的产品有所不同。由于产品升级或变更，本说明书在随时更新中，恕不另行通知或更正。0.2 C

11、orrectly using the manual Thank you for using the builders hoist made by EARNEST.Before installing and using the hoist,read the manual carefully.This manual should always accompany the machine in order to be available to the operator.Any uncorrect assemble,usage and maintenance may lead unexpected r

12、isks.Sketches in this manual are only used to explain the principle ,they may be not consistent with your machine.Because of the machine upgrading or altering,content of the manual is always changing .We will not inform .0.30.3 安全提示及安全标识安全提示及安全标识0.3.1 说明书中提示安全的用语采用了突出显示或使用“注意” “警告”等用语，请仔细阅读。0.3.2 产品

13、上印刷或粘贴有黄色警示标识，请注意查看和辨别。0.3 Safty tip and mark0.3.1Security terms of the instruction manual prompted a highlight or use notes warn terms, please read carefully.0.3.2Printing or paste with a yellow warning identified on the product, please note that to view and identify.0.40.4 安全风险提示安全风险提示使用升降机时，可能存在以

14、下风险。应对安装、操作、使用和维护保养人员进行安全告知和安全教育，并采取措施降低可能存在的风险。0.4General indication about safetyUsing the machine exist risks as follows. All the people involving ininstall,operating and maintenance shoud be informed the risks,and protection procedures shoud be adoped.3从层门或通道口滑到、绊倒或坠落；Sliding,stumbling or falling

15、 from the landing gate.外围栏入口、层门入口、吊笼出入口开关门时可能引起挤压、碰撞、夹伤；Hurt by squeezing,crashing or clipping in the entrance of guardrail,landing and cage.启停会产生冲击，限位失灵可能发生猛烈的坠地冲击；Shocking caused by sudden starting or stopping,especially violent shocking caused by the cage landing on the ground because of limiters

16、 in error.升降运行时产生不规则的振动；Irregular vibration during the machine running.座椅与操作台的高低或间距可能引起操作者身体不适；Discomforty caused by a wrong ergonomic drawing.机械或电器噪声可能导致听力障碍；Mechanical or electrical noise can cause hearing impairment.装载物品倾覆可能从吊笼围壁挤出； cargoes extrud out of cage.电器电线漏电导致触电；Wire leakage causes electr

17、ic shock.变频器产生电磁辐射或干扰；Electromagnetic radiation or disturbing cause by inventer.齿轮齿条传动可能缠绕、吸入或卷入异物引发意外事件；Something pulling into between gear and rack. 突然停电可能引起机器零部件损坏或功能混乱导致危险；Sudden losing power may lead to function chaos or damages of parts.观察运动部件的视线不良引起危险；Risks caused by the poor sight of observi

18、ng moving parts.运行通道有障碍物引起危险；Risks caused by obstructions in hoist way.触摸到电机或制动电阻时可能引起烫伤； Scalded when touch the motor or the braking resistance.减速器内热油或蒸汽喷出；Thermal oil or steam erupt out of reducer ;超载装置、限位装置在安装调整时出现人为差错可能导致安全装置失效；Risks caused by human error when installing or adjusting overload de

19、vice, limiting device.扶靠护栏时栏杆缺失或失效导致跌落的危险；Rely on the fence railing which is missing or invalid .4启、停、上、下标志或符号装置未调整到与实际一致；Start, Stop, upper and lower flags or symbols appliance is not adjusted to the actual consensus .装载时严重偏载导致结构稳定性丧失；Serious unbalanced loading results in the loss of structural sta

20、bility .超载引起失速失控或结构失稳；Stall ,out of control,instability caused by overloading.零部件脱落导致的倾覆、出轨；Parts falling off lead to overturning, or go off the rail人或货拥挤时从联锁失灵的门处意外坠落；Crowded passengers or goods fall out from the unexpected openning gate;顶部操作时，头手伸出护栏外可能与护墙装置等碰撞。 Running the hoist at the cage top, h

21、ands and head outside the fence may collide with the attachment.0.50.5 保修说明保修说明0.5.1 本产品保修期为十二个月，保修期内按照使用说明书正常使用情况下，产品发生故障或损坏，我公司负责免费维修。齿轮、齿条、滚轮、轴承、按钮、操作手柄、接触器、中间继电器、滑轮、电缆、灯具等易损件换件收取成本费。外观的划伤及油漆脱落等不在保修范围内。0.5Warranty description0.5.1This product is warranted for 12 months. If the product fails under

22、 normal use according to manual, the company responsible for the maintenance free. Wearing parts such as bearings, gears, rack, buttons, action handles, contactors, relays, pulleys, cables, lamps and etc. will charge the cost .0.5.2 保修期内，因以下原因导致损坏，将收取一定的维修费用：0.5.2 In warranty period, damage caused b

23、y the following reasons, certain maintenance costs will be charged :因使用上的错误及自行擅自修理、改造而导致的设备损坏；Due to errors on the use and unauthorized repair or modification.由于火灾、水灾、电压异常、其它天灾及二次灾害等造成的设备损坏；Due to fire, flood, abnormal voltage, other natural disasters.购买后由于人为摔落及运输导致的结构及元器件损坏；Due to fall or capsizing

24、 during tranporting.不按我司提供的说明书操作导致的设备损坏；Due to action not accordance with the instruction manual.因设备以外的因素造成损坏。Due to external factors.50 0.6.6 免责声明免责声明0.6 Disclaimers我公司生产的施工升降机都是经过严格检验、检测后出厂的合格产品，附有铭牌、使用说明书、监督检验资料以及各种附件等。未按照说明书要求进行安装、使用、维修、保养，使用非本公司提供的备件、附件等，导致的质量和安全事故与本公司无关。Our builders hoists are

25、 qualifying products passed by strict inspection, testing and supervision. Not in accordance with the instruction manual required to install, use, repair, maintenance, not use of the spare parts provided by the manufacturer, that cause of quality and safety accident had nothing to do with the manufa

26、cturer.- 6 -1 1 产品概述产品概述 Outline and Feature1.11.1 升降机型号说明升降机型号说明 Model descriptionSC200/200TD V11.21.2 升降机性能参数升降机性能参数 Performance parameters产品型号 TypeSC200/200TD-V1V2V3额定载重量 Rated load capacity (kg)22000额定 Rated33455463起升速度 Lifting speed (m/min)最大 Max0400545463最大架设高度 Max height(m)450最大附着间距 Max inter

27、val between mast-tie (m)10.5最大悬垂高度 Free height above last mast-tie (m)7.5电机功率 Motor power(kw)22122218.522202320限速器型号 Anti-falling safty device modelSAJ40-1.2SAJ40-1.4吊笼内空（长宽高）Cage space (LBH)(m)3.21.52.3吊笼重量 Cage wt.(include drive unit)(kg)21850218802190021950外笼重量 Enclosure wt.(kg)1500765150766.3170

28、768.0190标准节重量Mast section wt.(kg)7610210环境温度 Environmental temperature (C)-20+50海拔高度 Altitude(m)1000电源 Power supplyAC380V 50HzV1-速度标记 Marks of velocity空白-33m/min, non means 33m/min V1-45m/min,V2-54m/min,V3-63m/min TD-传动机构在吊笼上方Drive unit at the top of the cage200-吊笼 1 载重量 2000kgCage 1 load 2000kg200-

29、吊笼 2 载重量 2000kgCage 2 load 2000kgSC-齿轮齿条式无对重施工升降机Rack and pinion hoist without counter-weight- 7 -1.31.3 升降机结构综述升降机结构综述 Summary of the structure1.3.1 施工升降机的外观尺寸及主要组成部分如下The builders hoist main size and components are as follows.1 外笼 Enclosure 2 吊笼 Cage 3 导轨架（标准节）Mast (section) 4 附墙架 Mast-tie 5 传动装置

30、Drive unit 6 电缆装置 Cable unit 7 电控系统 Eletric unit 8 电动卷扬机 Electric winch5310428020003300（ 3000）331528001508650附 着 间 距 Interval between mast tie Max.10500悬 高 Free height Max.7500123546784030510217251773- 8 -1.3.2 外笼1.3.2 Enclosure外笼由固定标准节的底盘和防护围栏组成。外笼门由机械和电气锁定，除非吊笼落下来，否则外笼门将不能打开。如外笼门未关，吊笼将不能启动。外笼门槛高度

31、450mm（如果使用电缆滑车，门槛可增高至 750mm） 。The enclosure is made up of chassis and protective fence. Unless the cage landing the floor, the enclosure door cannot be opened becuase of mechanical and electrical interlock.If the enclosure door is not closed, the cage will not run.The door sill height is 450mm(if th

32、e cable car used,the height up to 750mm)。底盘的标准节联接部分可与其它部分分离，便于升降机导轨架安装在地平面以下。Parts of chassis that joining the mast section can be separated from the rest.It is easy to set up the hoist at below ground level.542020002850(3150)外 围 栏Guard rail外 笼 门Enclosure door检 修 门Access door电 源 柜Power supply cabine

33、t底 盘Chasis45042801228（ 750）17251773- 9 -1.3.3 吊笼1.3.3 Cages吊笼为一钢结构件，四周有坚固的冲孔网，并设有进、出口门，由安装在吊笼上的滚轮沿导轨架运行。The cage as a steel structure surrounded by solid punch mesh plate, with inlet and outlet , runs along the mast rails by its rollers.吊笼上设有安全钩以防止吊笼从导轨架顶部脱离。The cages have safety hooks to prevent th

34、e hoist aparting the mast at top end.吊笼顶部,由安全栏杆围住,可作为工作台。顶上有一活板门，通过配备的专用梯子，可方便的攀登到顶上进行安装和维修。通过门用一个梯子可以到达顶部。The cage top with guard rail can be used as a platform. The top has a gate.Through it with a ladder can reach the cage top. 1.3.4 导轨架（标准节）1.3.4 Mast (section)标准节每节长 1508mm，装有两根传动齿条（与底盘联接的标准节不安装

35、齿条） ，多节标准节用螺栓联接组成导轨架，通过附墙架与建筑物固定。The standard sections 1508mm long with two drive racks constitute the mast as the cage rails. The mast attach to the buildings with mast-ties.标准节共有5mm、6.3mm、8mm、10mm 等不同立管厚度，进行组合后能达到最大 450m 的高度。不同安装高度时所需要各规格标准节的数量（米）如下表所示。不同规格之间安装过渡节。The mast section has different ve

36、rtical tube thickness such as 5, 6.3, 8, 10mm and so on. The assemble maximum height can reach 450m. The height requires different number of sections as follow table.A transmit section should be installed between 1800331526003700560吊 笼 门Cage door司 机 室Driver cab滚 轮roller安 全 钩Safty hook栏 杆Guard rail-

37、10 -deferent spicification sections.标准节立管规格Mast section vertical tube specifications安装高度Setup height（m）7610768766.3765150-150270-120150390-120120150450601201201501.3.5 附墙架1.3.5 Mast-tie附墙架用于导轨架与建筑物之间的支撑，有三种组合型式，适合导轨架中心距离附墙面1.82.6m、2.63.0m、3.04.0m。沿导轨架高度，一般每隔 310.5m 安装一个附墙架。The mast-ties as support b

38、etween the buildings and the mast have three types of combination,for distance between mast center and wall 1.83.6m. Along the mast generally every 310.5m a mast-tie should be installed.1.3.6 传动机构1.3.6 Drive unit传动机构由多个电动机、电磁制动器、弹性联轴器、减速器及传动齿轮等组成。传动机构在吊笼上通过齿轮与齿条啮合，使吊笼运行。The drive unit consists of se

39、veral motors, electromagnetic brakes, flexible couplings, gearboxes and drive gears and so on. The drive unit in the cage top drags the cage to 650 65015081522 76 5/6.3/8/10726800- 11 -run along the masts.两传动机构 Drive unit with two motors10701263508574电 机Motor减 速 器Motor870- 12 -三传动机构 Drive unit with

40、three motors1.3.7 电缆装置1.3.7 Cable device电缆装置，用于使接入吊笼内的电缆随线在运行时不偏离电缆通道，保持在固定的位置。电缆导向装置包括随行电缆和若干个电缆保护架。当提升高度小时使用电缆桶，高度大时则需要使用电缆滑车。Cable unit is used to protect the trailling cable from deviate its channel and to fix its locations. Cable unit consists of trailling cable and a number of cable protection

41、 frames. When lifting height is short, cable 10701653508574电 机Motor减 速 器Motor8709.0 5- 13 -barrel is used.Otherwise cable car is used. 电缆桶 Cable barrel 电缆滑车 Cable car1.3.8 电动卷扬机电动卷扬机用于在没有其他起重设备时加节或降节，最大起重 200kg，不能用于其它目的。1.3.8 Electric winchElectric winch is used to increase or decrease the mast heig

42、ht when no other lifting equipment.Its maximum load is 200kg .It cannot be used for other purposes.1.41.4 安全装置综述安全装置综述1.4.1 防坠安全器防坠安全器安装在吊笼内，由外毂、制动锥鼓、离心块、弹簧等组成。当吊笼超速运行时，安全器里的离心块克服弹性拉力带动制动锥鼓旋转，与其相连的螺杆同时旋进，制动锥鼓与外毂接触逐渐增加摩擦力，确保吊笼平缓制动。同时切断控制线路使传动装置断电停车。1.4 Safty device1.4.1 Anti-falling safety device Ant

43、i - falling safety device installed in the cage, consits of an external hub, brake cone drum, centrifugal block, spring and so on. When the cage over speed, the centrifugal overcoming the elastic tension drives the brake cone drum rotation and inrease frictions between drum and hub,finally this make

44、s the cage stopped.At the same time the power is cut off.1.4.2 起重量限制器升降机安装有起重量限制器，当载荷达到额定载重量 90%时，会持续报警；在载荷达到额定载重量 110%前，断开控制回路，中止吊笼起动，保护施工升降机安全。变频升降机在 60%额定载荷时会使轻载高速无效。3400159041001700- 14 -1.4.2 Load limiterLoad limiters are equipped in the hoist. When the load reaches 90 percent of the rated capa

45、city, the buzzer will sound continuedly. When the load reaches 105 percent, the cages can not run. The limitor will invalidate the high speed when the load more than 60% rated in the invert hoist.1.4.3 限位开关当吊笼行至上、下终端站时，在限位开关及控制器件作用下，可自动停车。变频控制的升降机有高速限位功能。1.4.3 Limit switchWhen the cages go to the to

46、p or bottom terminal station, under the effect of the limit switch and control devices, the cages will automatically stop. The invert hoist has additional limit switch to invalidate the high speed.1.4.4 极限开关当吊笼行至上、下终端站因故障不能停车时，在安全距离内极限开关动作切断总电源，使吊笼制动。1.4.4 Power limit switchWhen the limit switch fai

47、l to stop the cage in the end station, the power limit switch will cut off the power, so that the cage stops within a safe distance .1.4.5 落地缓冲吊笼在下终端站因故不能停车时，底部有缓冲弹簧或橡胶体减轻坠落冲击损害。 81.4.5Landing bufferWhen the cage fails to stop at bottom station, the buffer springs or rubbers on ground will reduce th

48、e falling impact damages.1.4.6 防冲顶装置冒顶冲出导轨脱轨起重量限制器Load limiter接近开关Limit switch极限开关Power limit switch- 15 -导轨架的最后一个标准节的端部被槽钢及螺栓封住，防止吊笼在上终端站因故不能停车而冲出导轨。为保证吊笼不冲顶，最后一个标准节不安装齿条。1.4.6 Anti- derail deviceThe end mast section is capped with anti-derail device to prevent the cages run over the top end. No ra

49、ck is installed in the end section.1.4.7 电气门锁吊笼的进出口门及吊笼顶部活板门上均设有安全开关（其结构同限位开关） ，任意一门开启时，吊笼不能运行，运行中的吊笼会立即停止。1.4.7 Electric door lockEntrance , exit and top door are equipped with safety switches ( the same as limit switch ).Any door is opened, the cage can not run ,running cage will stop immediately.

50、1.4.8 机械门锁吊笼离开下终端站后，外笼门及吊笼单开门均被机械装置锁死，不能开启。1.4.8 Mechanical lockWhen the cage leaves the guard rail, the fence gate and cage entrance cant be opened.吊 笼 门 锁Cage entaance lock外 笼 门 锁Fence gate lock防 冲 顶 装 置Anti-derail device没 齿 条 的 标 准 节Section without racks防冲顶装置Anti-derail device吊笼门锁和外笼门锁Mechanical

51、lock- 16 -2 2 基基 础础 Foundation2.12.1 基础载荷计算基础载荷计算基础载荷 P 按以下计算：P=安全系数 n(吊笼重+外笼重 +导轨架总重+载重量)考虑动载荷、风载及附墙装置的影响，安全系数取 n=2例：SC200/200TD 型升降机，架设高度为 100m吊笼重：22200kg外笼重：1500kg导轨架总重(共需 66 节，每节重150kg)：66150kg吊笼载重量：22000kg基础承载2.1 Foundation Load CalculationFoundation load P in the follow termsP= Safety factor(c

52、age weight +guard rail weight+mast weight )Considering dynamic load, wind load and effect of mast-tie, safety factor n=2Example : SC200/200TD hoist, erecting a height of 100m,The cage weight : 22200kg,The guand rail weight : 1500kg, The mast weight of a total 66 sections, each section is heavy 150kg

53、:66150kg,The cage load : 22000kg .The foundation bearing capacity P=(22002)+1500+(15066)+(20002)2=39600kg按能承受最大压力 Pmax=39600kg 设计的基础符合升降机的使用要求。The foundation maximum load 39600kg meet the requirements of the hoist.2.22.2 基础基础技术要求技术要求2.2.1 基础承受的载荷能力应大于 P=(吊笼重+外笼重+导轨架总重+载重)2 2.2 Foundation requirement

54、s2.2.1 The Foundation should bear greater than 2 times P as total weight of the hoist.2.2.2 混凝土基础下地面的承载力应大于0.15Mpa。2.2.2 The ground pressure should be greater than 0.15Mpa.2.2.3 双层钢筋网：钢筋直径 12mm，间距 200mm。2.2.3 Double mesh in concrete : bar diameter 12mm, 200mm interval.2.2.4 尺寸 L 为升降机标准节中心与附墙支座安装面的距离

55、 1.84.0m。2.2.5 基础预埋螺栓应与双层钢筋网焊接牢固。2.2.4 L as the distance between mast center and the mounting surface of the mast-tie should be in the range 1.84.0m .2.2.5 Foundation bolts must be welded with the steel bar mesh.2.2.6 基础上平面应高于地平面，否则应采取防积水措施。2.2.6 The top of the foundation should be higher than the g

56、round ,otherwise water - prevention measures should be taken.- 17 -2.3 基础图基础图 Foundation drawingSC200/200TD施 工 升 降 机 基 础Hoist Foundation建 筑 物Building1609603804400（ 双 笼 ）38003001800 4000M30-6g 301504201701 双 层 钢 筋 网 ： 钢 筋 直 径 12mm， 间 距 200mm。2 砼 标 号 不 小 于 C303 砼 浇 筑 前 应 将 预 埋 基 础 螺 栓 与 两 层 钢 筋 网 焊 接

57、4 基础 找 平 层 平 面 度 小 于 1/5005 基 础 地 面 的 承 载 能 力 应 大 于 0.15MPa6 基 础 承 受 的 载 荷 能 力 应 大 于 P： P=(吊 笼 重 +外 笼 重+导 轨 架 总 重 +载 重 ) 0.02 (KN)7 基 础 应 采 取 防 集 水 措 施 ， 以 免 腐 蚀 基 础 造 成 危 险1D ouble-layerm eshreinforcem entw ithbardiam eter12m mandinterval200m m2T heconcretestrengthisnotlessthan30M pa.3E m beddedbol

58、tsshouldbew eldedw iththesteelbarsbeforetheconcretepouring4T heflatnessofthefoundationtopislessthan1/15005T heearthunderthefoundationloadcapacityshouldbegreaterthan0.15M pa6T hefoundationloadcapacityshouldbem orethan2tim esofthetotalw eightofthehoistanditsloadincludingthew eightofcages,enclosure,m a

59、stsectionsandm ast-ties.7W ater-preventionm easuresshouldbetaken.地 脚 螺 栓 Embeded bolt材 料 Material： Q235B数 量 Qty： 414005502800（ 单 笼 ）- 18 -3 3 附墙装置附墙装置 Mast-tie3.13.1 附墙架作用于建筑物上力附墙架作用于建筑物上力附墙架作用于建筑物上的力按照下式计算F=L6/(B2.05) 吨3.1 Force acting upon the buildingForce acting upon the building by the followin

60、g caculationF=L6/(B2.05) tonF-附墙架作用在建筑物上的拉压力（吨）F-Force of mast-tie acting on the building (ton)L-标准节中心与附着面的距离（米）L-Distance between mast center and attach- point (m)B-附着点间距（米）B-Attachment point width (m)3.23.2 附墙架结构附墙架结构附墙架由臂、小架、大架、支撑管、斜拉杆和附墙座组成。臂用 U 形螺栓固定在标准节上，附墙座固定在建筑物上。通过多种组合可适用于附着间距为1.84.0m 的情形。3