锂电池规格书

1、. 储能型磷酸铁锂电池规格书STORAGE LiFePO4 BATTERY SPECIFICATIONS客户名称(Customer)： 产品型号(Type)： CF12V80Ah 发行日期(Issuing Date)： Prepared制定 Checked审核 Approved批准 1. 适用范围(Product Scope)本规格书描述了锂离子二次电池的技术要求、测量方法、运输、储存及注意事项。This Specification describes the requirements of the lithium ion rechargeable battery supplied by 2.

2、 电池组特性 (Battery Group Specifications) Cell电芯Model 规格型号IFP8081230-10AhCapacity 容量10 AhRated Voltage 标称电压3.2 VInternal Resistance 内阻标准4 mCombination Standard 配组标准A. 容差Capacity Difference1% B. 内阻Resistance()=12 m C. 荷电保持能力Current-maintaining Ability90% D. 电压Voltage3.33.4VCombination Method 组合方式4串8并 4S

3、8PPile Index成品参数Rated Capacity 标称容量80.0Ah Minimal Capacity 最小容量（0.3C5A）80.0AhNominal Voltage 额定电压12.0VMax. Charge Voltage 最大充电电压14.8 VDischarge cut-off voltage 放电截止电压10.0VCharge Current充电电流5-10AWorking Current 工作电流10-20AOutput and Input输出端与输入端P+(red) / P-(black)Weight 电池重量 9.2KgDimension 外形尺寸（LWH）16

4、8260132mm(不包含外露开关)Charge Method适用充电Standard 标准5A16hrsQuick 快速20A4hrs. Operating Temperature 适用温度Charge充电045；32oF113oFDischarge放电-2060；-4oF149oFManagement system 管理系统Single cell over-charge cut-off voltage单只过压保护值3.9V Charge Working voltage过压释放值3.8VSingle cell under-discharge cut-off voltage单只欠压保护值2.3

5、VDischarge working voltage欠压释放值2.7VConditions of over-charge and under-discharge voltage recovery过、欠压恢复条件With the high-point voltage reaching the working voltage 极限电压达到释放值Over-charge cut-off current 过流保护值80AShort-circuit protection 短路保护Own this ability 具备此功能Condition for the recovery of over-current

6、 and short-circuit protection 过流短路保护恢复条件Cut the circuit to automatic recovery 断开负载自动恢复单只电芯曲线图feature curve for single cell3. 技术要求 (Technical Requirements)3.1测试条件(除特别规定) Testing Conditions (unless otherwise specified) 温 度Temperature: 1535相对湿度Relative Humidity: 45%75%大气压Atmospheric pressure: 86106Kpa3

7、.2充放电性能 (Electrical Characteristics)NO项目(ITEM)测试方法(Testing Instruction)要求(Requirements)1Standard Charge标准充电Charging the cell initially with constant current at 0.5C and then with constant voltage at 3.7V till charge current declines to 0.05C先用0.5C恒流充电至3.7V，再恒压3.7V充电直至充电电流0.05C2Rated Capacity初始容量Meas

8、ure discharge capacity with discharge current 1C to 2.5V cut-off within 1 hour after standard charge.标准充电方式充电后，以1C电流放电至2.5V的容量80Ah3Cycle Life循环寿命Measure the capacity after 2000 cycles of standard charge and discharge at 1C current to 2.50V cut-off 标准充电方式充电后，1C放电至2.50V，如此循环2000次后电池的剩余容量 80% of Rated

9、Capacity初始容量的80%4Storage Characteristics 储存性能Capacity after 30days storage at 25 from standard charge标准充电方式充电后，25下储存30天后的容量Retention capacity90%剩余容量90%Capacity after 7days storage at 60 from standard charge标准充电方式充电后，60下储存7天后的容量Recovery capacity 90%剩余容量90%3.3环境性能 (Environmental Characteristic) NO项目(I

10、TEM)测试方法(Testing Instruction)要求(Requirements)1Temperature testing高低温测试Measure capacity with constant discharge current 0.5C to 2.5V cut-off at each temperature after standard charge at 25, Percentage as an index of the capacity compared with 100% at 2525下标准充电方式充电后，在指定温度下0.5C放电至2.5V的容量，并以25时放电容量为基准计算

11、百分率70% at 0100% at 2596% at 602Constant temperature /humidity恒定湿热性能Keep the battery at 40 and 90%RH for 96hrs将电池放入温度为40，相对湿度为90%的条件下搁置96小时Recovery capacity 85%恢复容量85%3.4机械性能 (Mechanical characteristics)NO项目(ITEM)测试方法(Testing Instruction)要求(Requirements)1Vibration振动After standard charge, fixed the ce

12、ll to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minutes per axis of XYZ axes. 将标准充电后的电芯固定在振动台上，沿X、Y、Z三个方向各振动30分钟，振幅1.6 mm，振动频率为10Hz55

13、Hz，每分钟变化为1Hz。The battery shall not rupture, smoke, catch fire, vent or leak and the voltage not be lower than 2.5V电池应无破裂、冒烟、着火、泄漏或漏液，并且电压不低于2.5V2IFPacting Testing碰撞After vibration , the battery will be IFPacted 100010 times(6020 times per minute) with the acceleration of 100 m/s2 and pulse lasting t

14、ime 16ms. 将振动后的电池以峰值加速度为100 m/s2的脉冲撞击100010次(平均每分钟6020次)，脉冲持续时间为16ms3Free fall自由跌落After IFPacting, the battery will be dropped free five times in three mutually perpendicular directions from the height of 1.0m onto a hard board with the thickness of 20mm碰撞实验结束后，将电池由高度为1m的位置自由跌落到置于水泥地面上的20mm厚的硬木板上，从X

15、、Y、Z正负方向（六个方向）每个方向自由跌落1次3.5安全性能 (Safe Characteristic)NO项目(ITEM)测试方法(Testing Instruction)要求(Requirements)1Short Circuit短路After standard charge，the battery located in a fume hood is to be short-circuited by connecting the positive and negative terminals with an external load of less than 50 m till the

16、 battery case temperature has returned to near ambient temperature.将标准充电后的电池置于通风橱中，短路其正负极（线路总电阻不大于50mV），实验过程中监视电池温度变化，当电池温度下降到接近初始室温时，结束实验The battery shall not rupture, smoke, catch fire, vent or leak.电池应无破裂、冒烟、着火、泄漏或漏液2Abnormal Changing Test 过充After discharge to 2.5V cut-off with discharge current

17、1C, the battery is to be subjected to a charging current 3C.The specified charging current is to be obtained by connecting a resistor of the specified size and rating in series with the battery. The test time is to be calculated using the formula: tc=2.5c/3(Ic) 将电池1C放电至2.5V后，调节电流3C充电，充电时间按以下公式计算：tC

18、= 2.5*电池额定容量/(3*制造商给定1C电流)3Over discharge testing过放After standard charge, the battery will be connected with external with a maximum resistance load of 0.1 for 24hrs until it is completely discharged and the battery case temperature has returned to near ambient temperature.以标准方式充电后，将电池正负端以内阻小于0.1欧姆的

19、铜导线连接24小时.，直至电池完全放电，温度下降到环境温度4Puncture穿刺After standard charge，the battery located in a fume hood is to be punctured with a nail (diameter1mm) until it is completely discharged and the battery case temperature has returned to near ambient temperature将标准充电后的电池置于通风橱中，用直径不小于1mm的针将电池从正面刺穿，直至电池完全放电，温度下降到环

20、境温度4 电池组基本性能 (Basic Characteristics of Battery) 2.1电池型号Battery Type4S8P IFP80812302.2外壳材质Material of Case环氧树脂Epikote2.3额定电压Nominal Voltage12.0 V2.4额定容量Nominal Capacity80Ah(0.2C)2.5内阻Internal Resistance400 mW2.6放电截止电压Discharge Cut-off Voltage10.0V2.7最大充电电流Max Charge Current40A2.8最大放电电流Max Discharge C

21、urrent160A2.9最大充电电压Max Charge Voltage14.8V2.10充电方法Charge methodCC/CV (constant current/constant voltage)CC/CV (恒流恒压)2.11尺寸Dimension长度Thickness: 260mm 宽度Width: 168 mm高度Height: 132mm2.12重量Weight约：9.2Kg About: 9.2Kg5 电池组保护功能要求 (Battery Required Protection Functions)To insure the safety, charger and the

22、 protection circuit shall be satisfied the items below. As safety device, please use in combination with the temperature fuse. The standard charge method is CC/CV (constant current/constant voltage)为确保安全,充电器和保护电路应符合以下要求。同时请使用装有热熔保险丝的安全装置。标准充电方法为CC/CV(恒流/恒压)5.1 参数(product Specification)名 称(NAME)项 目(I

23、TEM)值 (value)精度（Precision）单 位(unit)过充电压(Over voltage)过充检测电压 Ocv390025mV过充恢复电压 Vcl380050mV延迟Delay Time10.5S过放电压(Under Voltage)过放检测电压 Vcu230080mV过放恢复放电 Vcl2700100mV延迟Delay Time10050mS充电电流(Charge Current)充电电流OC5A过流延迟OC Delay Time1000100mS工作电流(Current)持续放电电流（Continuous Output Discharging Current）20A过放电流

24、(Over Current)过放保护电流OC805A过流延迟OC Delay Time105mS静态电流(Current Consumption)工作状态 Normal Mode30uA休眠状态 Sleep Mode0.1uA短路(Short Circuit)短路电流 SC600150A延迟 Delay Time1000uS恢复条件Recovery Condition断开负载Manual regulation6 保质期限及产品责任WARRANTY PERIOD & PRODUCT LIABILITYWarranty period of this product is 24 months fro

25、m manufacturing code.保质期是从出厂日期(喷码)开始起二十四个月.CHINENG is not responsible for the troubles caused by mishandling of the battery which is clearly against the instructions in this specification. 池能公司对因没有按本规格书规定操作而导致的意外不负责任When CHINENG finds any new facts which require modification of this document, we wil

26、l inform you again. 一旦池能公司发现本规格书有新的修改细节，我们将再告知。7 包装电池上的标示INDICATIONS ON BATTERY PACKThe following warnings should be indicated on the battery packs.以下警告应注明在包装后的电池上 Use a specified charger. 使用规定的充电器 Do not throw the battery into fire, or heat. 不要将电池投入火中或加热 Do not short-circuit the battery terminals 不

27、要将电池两端短路 Do not disassemble the battery. 不要将电池分解拆散8 电池使用时警告事项及注意事项WARNINGS AND CAUTIONS IN HANDLING THE Lithium-ion BATTERY To prevent a possibility of the battery from leaking, heating or explosion please observe the following precautions:为防止电池可能发生泄漏,发热、爆炸,请注意以下预防措施：WARNINGS!1. Do not immerse the b

28、attery in water or seawater, and keep the battery in a cool dry surrounding if it stands by. 严禁将电池浸入海水或水中,保存不用时,应放置于阴凉干燥的环境中2. Do not use or leave the battery near a heat source as fire or heater 禁止将电池在热高温源旁,如火、加热器等使用和留置3. When recharging, use the battery charger specifically for that purpose 充电时请选用

29、锂离子电池专用充电器4. Do not reverse the positive (+) and negative (-) terminals 严禁颠倒正负极使用电池5. Do not connect the battery to an electrical outlet 严禁将电池直接接入电源插座6. Do not discard the battery in fire or heat it 禁止将电池丢于火或加热器中7. Do not short-circuit the battery by directly connecting the positive (+) and negative

30、 (-) terminal with metal objects such as wire. 禁止用金属直接连接电池正负极短路8. Do not transport or store the battery together with metal objects such as necklaces, hairpins etc. 禁止将电池与金属,如发夹、项链等一起运输或贮存9. Do not strike or throw the battery 禁止敲击或抛掷、踩踏电池等10. Do not directly solder the battery and pierce the battery

31、 with a nail or other sharp object. 禁止直接焊接电池和用钉子或其它利器刺穿电池CAUTIONS!1. Do not use or leave the battery at very high temperature (for example, at strong direct sunlight or in a vehicle in extremely hot weather). Otherwise, it can overheat or fire or its performance will be degenerated and its service l

32、ife will be decreased. 禁止在高温下（炙热的阳光下或很热的汽车中）使用或放置电池,否则可能会引起电池过热、起火或功能失效、寿命减短2. Do not use it in a location where static electricity is great, otherwise, the safety devices may be damaged, causing hidden trouble of safety. 禁止在强静电和强磁场的地方使用,否则易破坏电池安全保护装置,带来不安全的隐患3. If the battery leaks, and the electrolyte get into the eyes. Do not rub eyes, instead, rinse the eyes with clean running water, and immediately seek medical attention. Otherwise, it may injure eyes or cause a loss of sight. 如果电池发生泄露,电解液进入眼睛,请不要揉擦,应用清水冲洗眼睛,并立即送医院治疗,否则会伤害眼睛4. If the battery gives off an odor,