H3c5700链路聚合手工模式

1、Switch 和BRAS之间用Eth-Trunk链路连接。要求Switch 和 BRAS 之间的链路有较高的可靠性。配置手工负载分担模式链路聚合组网图BRASSwitchEth-Trunk 1DSLAM DSLAMGE0/0/1VLAN 100-150Eth-TrunkEth-Trunk 1GE0/0/4 GE0/0/3GE0/0/2VLAN 151-200配置思路采用如下的思路配置负载分担链路聚合：创建Eth-Trunk。加入成员接口。数据准备为完成此配置例，需准备的数据：l链路聚合组编号。l Eth-Trunk的成员接口类型和编号。2链路聚合配置Quidway S5700系列以太网交换机配

2、置指南-以太网操作步骤步骤1创建Eth-Trunk创建Eth-Trunk 1。 system-viewQuidway sysname SwitchSwitch interface eth-trunk 1Switch-Eth-Trunk1 quit步骤2向Eth-Trunk中加入成员接口将GE0/0/3 加入Eth-Trunk 1。Switch interface gigabitethernet 0/0/3Switch-GigabitEthernet0/0/3 eth-trunk 1Switch-GigabitEthernet0/0/3 quit将GE0/0/4 加入Eth-Trunk 1。Sw

3、itch interface gigabitethernet 0/0/4 Switch-GigabitEthernet0/0/4 eth-trunk 1 Switch-GigabitEthernet0/0/4 quit步骤3配置Eth-Trunk 1#配置Eth-Trunk 1允许VLAN100-200的报文通 过。Switch interface eth-trunk 1Switch-Eth-Trunk1 port link-type trunkSwitch-Eth-Trunk1 port trunk allow-pass vlan100 to 200Switch-Eth-Trunk1 qui

4、t步骤4验证配置结果在任意视图下执行display trunkmembership 命令，检查Eth-Trunk 1是否创建成功，及成员接口是否正确加入。Switch display trunkmembership eth-trunk 1Trunk ID: 1used status: VALIDTYPE: ethernetWorking Mode : NormalWorking State: NormalNumber Of Ports in Trunk = 2Number Of UP Ports in Trunk = 2 operate status: upInterface GigabitE

5、thernet0/0/3, valid, operate up, weight=1,Interface GigabitEthernet0/0/4, valid, operate up, weight=1,#显示Eth-Trunk 1的配置信息。Switch display eth-trunk 1Eth-Trunk1s state information is:WorkingMode: NORMAL Hash arithmetic: According to SA-XOR-DALeast Active-linknumber: 1 MaxBandwidth-affected-linknumber:

6、 8Operate status: up Number Of Up Port In Trunk: 2PortName Status WeightGigabitEthernet0/0/3 Up 1GigabitEthernet0/0/4 Up 1从以上信息、看出Eth-Trunk 1中包含2个成员接口GE0/0/3和GE0/0/4。成员接口的状态都为Up。结束Quidway S5700系列以太网交换机配置指南-以太网2链路聚合配置文档版本01(2010-09-10)华为专有和保密信息 版权所有华为技术有限公司2-25配置文件Switch的配置文件#sysname Switch#interface Eth-Trunk1port link-type trunkport trunk allow-pass vlan 100