CAD制图标准(中英文)

1、tST-PER005A中文标题CAD制图标准Chinese Title英文标题Standard of CAD drawingsEnglish Title格式编号ST-ITT003B文件编号ST-PER005A文件属性 ISOStyle SNFile No.File Type No ISO发行部门PE编 制 人董明亮Dong Mingliang文件类别 Rules Procedure GuideIssued byPrepared byFile Class部门审批批 准Checked byApproved by评 审PE / PP / ITReviewed by发行日期2007.3.14文件等级

2、公司 Corporation页 数7DateGrading 部门 DepartmentPagesCAD制图标准Standard of CAD Drawings为了使图纸更规范化，下面制定了一些相关的绘图规定：To better manage drawing making, here below are some drawing rules:1图纸规定Drawing Rules 1.1图框及周边Drawing Frame and Periphery 图框线用粗实线绘制，周边线用细实线绘制。Drawing frame is to be made in continuous thick line,

3、and the periphery is to be in continuous thin line.1.2标题栏Title 外框用粗实线绘制，其右边和底边与图框线重合，其余用细实线绘制。填写的文字，除名称中文用5号字、英文用3.5号字外，其余中文用3号字、英文用2号字，其中图号、材料也用5号字。Frame is to be made in continuous thick line, with its right and bottom line overlapping the drawing frame, others are to be made in continuous thin li

4、ne. Title must be in size 5 for Chinese, and 3.5 for English, and text are to be written in size 3 for Chinese and 2 for English, drawing No. and material are also expected to be in size 5.1.3图号栏Drawing No.外框大小12×55，用细实线绘制，文字与标题栏中的图号文字一致(即5号字)。Frame is to be made in the size of 12 X 55, in cont

5、inuous thin line, text is to be in the same size (5) as the title.1.4明细栏Specification每增加一行，间隔9mm，字高：中文：3，英文：2.5，宽度0.75。Row space is 9mm, character height: 3 for Chinese, 2.5 for English, width0.75.1.5字体Font图纸中所采用的字体，除单位名称用楷体_GB2312外，其余用HZ(romans,hzjd)字体。Except company name may use楷体_GB2312, all font

6、 in the drawings are requested to be in HZ(romans, hzjd)1.6图线Drawing Line1.6.1图线分为粗细2种，粗线的宽度为0.35mm，细线的宽度为0.13mm。Drawing line includes two types: thick line, with the width of 0.35mm; and thin line, with the width 0.13mm.1.6.2同一图样中，同类图线的宽度应基本一致。虚线、点划线及双点划线的线段长短和间隔应各自大致相等。Lines for the same drawing s

7、hall be in the consistent width, dashed line, dotted line and double dotted line must be in the consistent length and space.1.6.3绘制圆的对称中心线时，应超出圆外25mm；首末两端应是线段而不是短划；圆心应是线段的交点。在较小的图形上绘制细点划线或双点划线有困难时，可用细实线代替。Center line shall be 2-5mm outside the circle; the start and the end shall be in short continuo

8、us line instead of short dashed line; circle center must be the junction of the lines. When dotted thin line or double dotted thin line is too small to be drawn, it may be replaced with continuous thin line.1.6.4建议虚线与虚线（或其它图线）相交时，应线段相交；虚线是实线的延长线时，在连接处要离开。Suggest the continuous part cross when dashed

9、 lines (or other lines) meet; dashed lines shall be apart from the continuous line when become the extension.1.6.5画局部放大图时，应用细实线圈出被放大部分的部位，并用罗马数字顺序地标记。在局部放大图的上方中间标注出相应的罗马数字和采用的比例。When drawing needs to be partially enlarged, the enlarged part shall be marked out with continuous thin line and digital s

10、equence. And the relevant digital sequence and the scale used shall be marked out on the upper center of the enlarged part.1.7尺寸标注Dimension Label尺寸标注用细实线绘制，尺寸数字字高与尺寸箭头大小一致：A4：2.5；A3：3.5。Dimension label is to be made in continuous thin line, the arrow shall be in the same size as the digit height: A4

11、：2.5；A3：3.5。1.8技术要求Technical Requirement技术要求书写采用细实线，字高：A4：2.8；A3：4。Technical requirement shall be written in continuous thin line, character height: A4：2.8；A3：4.1.9图中的表格Forms一般情况下，字高与尺寸标注一致。如表格文字太多，可视情况而定。Usually the character height shall be consistent with the dimension label. But if the text is t

12、oo much, it may depend.1.10 表面粗糙度Surface Roughness代号中数字的方向必须与尺寸数字的方向一致。对其中使用最多的一种代(符)号可以统一标注在图样右上角，并加注“其余”两字，且应比图形上其它代（符）号大1.4倍。Digit in the symbol shall be in the same direction as dimension digit. And the most used symbol may be marked out in the right corner of the drawing, with remark of “Others

13、”, and the size of 1.4 times larger than other symbols.1.11剖切符号及箭头Section Symbol and Arrow剖切符号：粗线；箭头：细线。Section symbol: bold line; arrow: thin line.1.12 颜色：Color:1.12.1粗线：白色Bold line: white1.12.2细实线：洋红色Continuous thin line: carmine1.12.3中心线(点划线)：红色Center line (dotted line): red1.12.4双点划线：洋红色Double d

14、otted line: carmine1.12.5虚线：洋红色Dashed line: carmine1.12.6螺纹线：洋红色Helix: carmine1.12.7剖面线：黄色Section line: yellow1.12.8尺寸标注：文字：黄色； 尺寸线及箭头：黄色Dimension label:Text: yellow; dimension line and arrow: yellow1.12.9技术要求：绿色Technical requirement: green1.12.10图框：图框线：白色； 周边线：红色Frame:Frame: white; periphery line:

15、red1.12.11标题栏：线框：青色(外框是粗线，用白色)； 文字：绿色Title:Frame: cyan (frame to be in white bold line); text: green1.12.12明细栏：线框：青色(外框是粗线，用白色)； 文字：绿色Specification:Frame: cyan (frame to be in white bold line); text: green 1.12.13图号栏：线框：青色； 文字：绿色Drawing No:Frame: cyan; text: green1.12.14图中的表格：线框：青色； 文字：绿色Forms:Frame

16、: cyan; text: green1.12.15引出序号：指引线：黄色； 数字：黄色Introduction Sequence:Guide line: yellow; digit: yellow1.12.16剖切符号及箭头Section Symbol and Arrow剖切符号：白色；箭头：黄色Section symbol: white; arrow: yellow1.12.17赛彤Logo：青色Saitong Logo: cyan2工艺图规定Technology Drawing Rules工艺图的绘图规定可参照图纸规定，线型、颜色基本一致。工艺图纸里没有英文，且增加了工步、工艺内容，故字

17、体大小有些改动，除名称用5号字外，其余都用3号字。装配卡中的规格用5号字，且明细栏每增加一行，间隔7mm，字高为3。Technology drawing rules may refer to that for the general drawing, line, and color shall be consistent. There is no English in technology drawings, and process step and technology are added, therefore the font may change a bit: text to be in

18、 size 3 and title to be in size 5. text for assembly card shall be in size 5, and row space for specification shall be 7mm, character height: 3.3以上规定的几点说明Notes3.1大致规则是：除图形中的图线、标注外，其余线条用青色，文字用绿色；General rules: except drawing lines and labels, all lines are to be in cyan, and text is to be in green;3.

19、2图纸中所有的图形、文字不要超出其规定的范围，特别是表格类的文字，不要超出其表格线。如文字太多，可适当增加一行，或缩短文字的宽度，视情况而定；Graph and text shall not exceed the defined area, especially text in the form must not go out of the line. For example: if the text is too much, rows may be added, or the width of the text may be shortened, it all depends;3.3如图中出

20、现其它的符号、标记，请参照以上的规定自行定义即可。Other symbols or labels required may be defined according to the above rules.3.4以上规定中，白色代表粗线（宽度0.35mm），其它颜色均代表细线（宽度0.13mm），在打印时需设置一下各种颜色线的宽度；In the above rules, white refers to bold line (width:0.35mm), other colors refer to thin line (width: 0.13mm), please set line width when printing;3.5由于我们打印出来的图纸都是A4纸张，为了使其规范，所以电子版本A3与A4图纸中的尺寸标注、技术要求等字高有些区别；As drawings printed out are in A4, for better management, ch