毕业论文设计外文文献翻译

1、毕业论文（设计）外文文献翻译教 学 点： 靖江党校函授点 专 业： 船舶与海洋工程 学 号： 姓 名： 吴 红 根 指导教师： 孔 慧 敏 江苏科技大学继续教育学院 2017年4月12日63500散货船规格书总则第一章 目的本规格书及附带的图纸是为了描述一型单螺旋桨、柴油机驱动、单甲板、单壳运输散货船的设计、材料、建造和设备。总布置图、中横剖面图和厂商表作为规格书整体的一部分。规格书和附带的图纸互相补充说明。被附上的总布置图、中横剖面图和其他相关图纸仅仅是初步的，经双方同意，可以修改、完善或者改进。承造方在船舶的设计、建造、装备、试验和交付给买方时，须与合同规格书及图纸一致。除了在本规格书中明

2、确由船东供应和完成的项目外，承造方应按照本规格书的要求完成一条完整船舶所需的所有项目。设计施工、制作、安装、检验和工艺不能超出规格书范围，或不能超出认可图纸要求，承造方应根据造船惯例予以完成。假设建造合同和规格书有分歧、矛盾和不一致，应以建造合同为准。假设规格书和总布置图、中横剖面图及相关图纸有分歧、矛盾和不一致，应以规格书为准。无论如何，关于规格书与相关图纸间存有矛盾，除非是在规格书签字以后发生的经双方当事人同意的一些变化，否则以前者为准。假设规格书和经卖方同意的标准有分歧、矛盾和不一致，应以经和卖方协调一致的标准为准，如果认为有必要的话，这样的调整应该经过买方的同意，不能无理由的拒绝。船舶

3、在设计阶段或建造时期，建造方可以纠正规格书里的过失或错误，如必要的话也可以进一步地修改、改进和优化规格书，这些修改、改进和优化须征得买方的同意，不能无理由的拒绝。船舶在设计阶段或建造时期，建造方可以纠正规格书里的过失或错误，如必要的话也可以进一步地修改、改进和优化规格书，这些修改、改进和优化须征得买方的同意，不能无理由的拒绝。在“总则”里的描述适用于整个规格书的船体、舾装、内舾、机械和电气部分，如果“总则”里的描述和船体、舾装、内舾、机械和电气部分的描述有矛盾、分歧和不一致，应以“总则”为准。规格书中各章节的总则适用于相应的各章节，如果各章节的总则和其对应的章节的段落或句子发生冲突、矛盾和不一

4、致，应以各章节总则为准。如果在船体、舾装、内舾、机械和电气各部分之中有冲突、矛盾和不一致，以该布置、装置或设备所属部分的说明为准。一些规章制度的改善或变化在5-2“规范，惯例和规章”有详细说明，在合同签字后开始生效，买方和建造方需执行和服从协商一致的在合同价格、载重量、交货日期或一些其它的项目方面的调整，即便要，根据具体情况而定。例如“或者”，“如必要的话”，“当考虑到”，“可以”和其它的类似表达方式用在规格书里，它们的运用在于建造方的选择除有另外明确地注明外，所有的尺寸需满足ISO体系，无论什么情况下，“或相当的”这样的描述可以理解为用相等的生产标准和质量来代替。除非规格书另有说明的，在规格

5、书里面任何2次或多次提到的均认为仅提供或进行一次。厂商标准、建造方标准和/或另外公认的工业标准，只要这些标准和船级社规范不一致和/或本身有问题时，材料、机械、仪器和设备等必须由船级社认可和设计应符合中国工业标准(GB, CB)。第二章 总述2.1 总述“船东”和“建造方”提及的公司或者代理商同样在建造合同中详细说明。如果没有其它说明，总则部分的描述应用于规格书的所有部分，其它部分的描述应用于相应部分。如果规格书和图纸存在矛盾和不一致之处，以规格书为准。除船上不同部门或特别说明外，任何在规格书里提及两次或多次、但逻辑上为同一项目的设备只供应一次。船东任何超出规格书所列出的规则规范和/或规格书的要

6、求，必须经双方同意后实施。如果必要，将对合同价格、载重量、航速等可能产生影响的部分进行调整。对规格书、图纸或其他已签署的书面文件的修改和变更，由承造方和船东的受权代表进行签署. 这些作为合同的补充。2.2 材料除特别同意和/或在规格书和厂商表中有明确规定，材料、机械和设备等一般采用国内厂家产品。所有的结构钢板用在船舶建造和轮机上的包括锻造和铸造应该符合正常的造船航海工程质量，试验，检查和证书都要由船级社或监管人适时认可。所有木材都要风干和没有瑕疵.所有使用的材料要满足安全循环使用的要求。限制使用对健康和环境有伤害的材料。石棉、制冷剂（R12/R22）和HALON、含铅油漆和含锡的防污漆也不允许

7、使用。如有任何规格书中描述的材料在实际情况下无法取得，承造方有权选择船级社许可的合适的替代品。2.3 工艺所有用于本船的建造工艺应符合中国船舶建造标准和/或承造方标准惯例，如果需要应取得船级社的批准。承造方标准、惯例应提交给船东备查。应根据规格书和图纸，以及船级社和有关当局的要求进行施工。2.4 标准应尽可能采用以下标准进行船舶的建造，另外一些船级社适用的经公认的工业标准。a)ISO标准b)中国工业标准(GB, CSQS, CB, YB, etc.)c)承造方标准和承造方惯例2.5 测量标准原则上采用ISO标准.原则上船体、机械、设备等的设计和建造采用国际单位。所有测量单位诸如电力、压力表、温

8、度计、容积表、舱柜标尺、水尺等应采用国际单位。2.6 图纸和文件所有的图纸，计算，说明书均使用英文.所有铭板、警示牌等均使用英文。承造方提交4份图纸给船东认可，船东退2份带船东签字和意见的认可图纸给承造方。送船东认可的图纸范围按照经船东认可的“认可图纸清单”提供认可。船东在收到图纸后14天退审认可图（排除邮寄时间）。如果承造方在14个工作日内没有收到船东的回复，承造方应先发传真提醒船东处理和认可图纸。船东在承造方发出提醒后6个工作日内给出意见。承造方在收到退审意见后14个工作日内答复船东的意见。如果承造方没能答复，船东将认为意见已经自动接受。如果第一条船认可的图纸与后来的姐妹船相同，承造方无需

9、提交姐妹船的相关图纸给船东认可，但需注明姐妹船的船名/船号。在交船时，承造方提供3份完工图纸和主要机械设备的操作说明书给船东 ，并提供给船东一份所有可以提供的完工图纸和文件的光盘。完工图纸范围与船东认可的“完工图纸清单”一致。所有的完工图纸包括说明书/手册均使用英文，那些国外的设备除外。以下各两份图纸应放在船上，在通过苏伊士和巴拿马运河时使用。总布置图、舱容图、带设备清单的机舱布置图、中横剖面图、测深表、破损控制图应将以下带图框的图纸挂在船上，并放置在船东代表指定的位置。总布置图 1份带载重线标尺的舱容图 1份操纵性特性图 1份防火控制及安全图 1份美国海岸警卫队要求的油输送程序 1份无线电安

10、全证书 1份救生衣说明书每层甲板1份2.7 分包商应按照技术规格书和厂商表进行材料、机械、设备和其它部件的订货。2.8 船东供品下列项目由船东供应，承造人负责安装到船上。承造人提供遮蔽的安全处所，贮藏并移交船上。超出规格书规定的缆绳。超出规格书规定的风动工具，皮管，钢丝绳等所有海图、航海和无线电书籍、公司旗和国旗所有消耗品除救生艇内的所有医药和医疗设备 例如立体声的娱乐设备，录像机和电视等，除了规格书中提到的用具。油画和图画承造方标准以外的水手长和木匠的工具。除床垫以外的所有床上用品（枕头、毯子，被单，被子等所有餐桌用布（餐巾，桌布等）所有烹调配餐用具（陶器，餐具，银器，土器，玻璃器皿，锅，盘

11、等）超出规范要求的消防员设备打印机，复印机，计算机，传真机和另外的办公设备。货物系固的活动部件苏伊士运河探照灯，一个建在艏楼甲板用作装载，一个建在甲板上备用，吊柱由建造方提供。超出有关当局要求和/或规格书规定的航海设备。垃圾桶便携式货舱清理设备便携式运煤测量设备为船上局域网系统准备的电脑及配件（打印机，UPS,网络集线器，网卡等）除了在交船前的试验和试航中消耗部分，所有燃油，润滑剂，油脂/液压油，工作油和其它消耗液体及串油后滑油被验证合格后的滑油。船东提供试航用的润滑油，承造方支付在试航时消耗掉的润滑油费用。规范规则和规格书要求和供应商标准之外的所有其他备品、备件和设备，除非生产商在与船东/承

12、造方签订合同后，同意提供额外免费备用品的。2.9 备件和工具按照规范要求和供应商标准提供备件。工具按照承造方标准提供。除了安装在指定位置的，所有备件用不同的箱子存放，并在每个箱子上注明箱子里的内容。重的备件应存放在起吊设备可以吊到的地方。重的备件和工具应安装在辅机旁的架子/基座上2.10 干船坞在交船前无需进干船坞。2.11 船模交船前承造方提供每艘船一个1:200的船模。63500 DWT BULK CARRIER SPECIFICATION GENERAL PROVISIONSECTION 1INTENT It is intent of this Specification (herein

13、after called the Specification) and accompanying plans to describe and set forth the design, material, construction and equipment of a ocean going, single screw diesel driven single deck bulk carrier.General Arrangement Plan, Midship Section and Makers List to accompany and form an integral part of

14、the Specification. The Specification and attached plans to be complementary to each other.The attached General Arrangement Plan, Midship Section and other relevant drawings are preliminary only, which are subject to further modifications or improvements or optimizations to be mutually agreed by the

15、paritiesThe vessel to be designed, constructed, equipped, tested and delivered to the Buyer by the Builder in accordance with the Contract, these Specifications and Plan(s)The Builder to furnish all items required for the completion of the vessel in accordance with the specification except items spe

16、cifically stated herein as to be furnished and supplied by the Owner.Details in design, fabrication, installation, inspection and workmanship not covered in this Specification, or not covered by the approved plans, to be performed under the Standard practice of the Builder.In case of any discrepancy

17、 or inconsistency or contradiction between the terms and conditions of Shipbuilding contract and the SPECIFICATIONS, the former should govern and prevail.In case of any discrepancy or inconsistency or contradiction between the terms and conditions of this SPECIFICATIONS and associated plans/drawings

18、 including General Arrangement Plan and Midship Section, the former should govern and prevail. However, with regard to such inconsistency or contradiction between Specifications and associated plans/drawings as may later occur by any change or changes agreed by both parties after signing of the

19、 SPECIFICATIONS, then such change or changes shall govern and prevail.In case of any discrepancy or inconsistency or contradiction between the terms and conditions of the SPECIFICATIONS and the standard of agreed vendor , the former can be adjusted in accordance with the vendors standard , if deemed

20、 necessary by builder. Such adjustment should be subject to buyers consent , which can not be unreasonably withheld.In design stage or construction period of the vessel, the Builder may correct any errors, mistakes or omissions contained in the SPECIFICATIONS and also make any changes or improvement

21、s or optimization to the SPECIFICATIONS if deemed necessary by the Builder, such corrections, changes and improvements should be subject to buyers consent, which can not be unreasonably withheld.It is to be understood that the descriptions in "General provisions" are to be applied to the w

22、hole of the subsequent parts of Hull , Outfitting, Accommodation ,Machinery and Electric parts, if there should be any discrepancy or inconsistency or contradiction between the “General provisions” and Hull, Outfitting, Accommodation, Machinery and Electric parts, the “General provisions” shall prev

23、ailThe general provisions of each subsequent part should apply to whole of the part, In the event of any conflict or inconsistency or contradiction between general provisions of each subsequent part and other paragraphs or sentence of the part, the general provisions should prevail and govern.If the

24、re should be any conflict or inconsistency or contradiction among the Hull, Outfitting, Accommodation, Machinery and Electric parts, the description in the part that specifically describes or governs the arrangement, installation or equipment shall prevail.Any amendment or change in the Rules and Re

25、gulations as specified in Section 5-2" RULES, CONVENTIONS AND REGULATIONS ", coming into effect after signing the contract, is to be carried out subject to the agreement between the Buyer and the Builder in terms of adjustment of the contract price, deadweight, delivery date or any other i

26、tem, if any, as the case may be.When words such as “or” “if necessary”, “when considered”, “may” and other similar expressions are used in the Specifications, their application shall be at Builders sole discretion.All dimensions to be in ISO system unless where explicitly stated otherwise. Wherever

27、the term “or equivalent” to be understood to mean that any substitute shall be of the equal performance standard and quality.Anything twice or more mentioned or enumerated in this Specification is to be only supplied once or executed unless otherwise specifically mentioned.Materials, machinery and e

28、quipment etc. to be approved by Class as required and designed in accordance with the GB/CB standard , manufacturers standard , builders standard and/or other recognized industry standard as long as these standards are not inconsistent with the requirement of Classification and/or Regulatory body co

29、ncerned.SECTION 2GENERAL DEFINITIONS 2-1GENERAL ARTICALS The terms "Owner" and "Builder" refer to companies or their agents as defined in detail in the Building Contract.The description in Part I General Provision to be applied to all parts of the Specification, where as the desc

30、riptions in the other parts to be applied to the respective parts, if not described otherwise.In the event of any contradiction or any inconsistency between the descriptions of proper part and other parts in the Specification, the descriptions in the proper part to govern.Unless those for different

31、department on board or specifically described, repeated mention of the logically same item in the Specification does not mean that the item to be supplied more than once.Any requirement of the Owner, which is in excess of the requirements of the Rules and Regulations listed herein and/or the content

32、 of this specification, to be subject to agreement and possible adjustment to the contract price, deadweight, service speed, etc., which may be affected.Amendments and changes to the Specification, plans or other written documents to be signed by an authorized representative of the Builder and Owner

33、. These documents to be the supplement to the contract.2-2MATERIAL Materials, machinery and equipment, etc. to be of Chinese make unless specifically agreed and/or described in the Specifications and the Makers List.All structure steel used for the construction of the vessel and machinery including

34、key forgings and castings to be of normal shipbuilding and marine engineering quality, tested, inspected and certificated as when required by the Classification Society and Regulatory Bodies concerned. All wood to be well seasoned and free from defect.All using material can be safely recycled. Minim

35、izing the use of materials known to be potentially hazardous to health and the environment. Especially asbestos, refrigerants ( R 12 / R 22 ), HALON, Lead-based paint and Tin-based anti-fouling paint to be not used. If any material described in these Specification cannot be obtained under certain ci

36、rcumstances, the Builder to have the right to substitute suitable equivalent material to meet the requirement of the Classification Society.2-3WORKMANSHIP All workmanship entering into the construction of the vessel to be in accordance with the Chinese ship building standards and/or Builder's st

37、andard practice, applicable to this kind of vessel, subject to the approval of the Classification Society where necessary. The standards of Builder's practice to be submitted to the Owner for reference.All work to be carried out according to Specification and plans and to the requirement of Clas

38、sification Society and also regulatory bodies mentioned hereinafter.2-4STANDARDS The following standards to be applied to the construction of the vessel, as far as practicable .The other recognized industrial standards than below mentioned may be applied to meet the requirements of the Classificatio

39、n Society. a) ISO standardb) Chinese industrial standards (GB, CB, CSQS,YB,etc.)c) Builder's standards, and Builder's standard practice2-5UNIT OF MEASURE ISO standard to be followed generally.SI units to be adopted for design and construction of hull, machinery, equipment, etc. in general.Al

40、l measuring units such as power, pressure gauge, thermometer, volume gauge, tank scales, etc. to be in accordance with SI system.2-6PLANS AND DOCUMENTS All drawings, calculations, instruction manuals, etc. to be written in English.All name plates, caution plates etc. to be in English. The Builder to

41、 submit plans for approval to the Owner in four (4) copies and Owner to return two (2) copies of the plans to Builder with the Owner's signature and comment if any.The scope of plans for submitting to the Owner's approval to be in accordance with the drawing " Approval Drawing List &quo

42、t; which to be approved by the Owner.The Owner to return approved plans within 14days (excluding express mailing time) after receipt of the drawings.If the Owner fails to return the drawings and/or to send by any comments to the Builder within14 days, the Builder to send fax reminder to Owner first

43、prior treating the drawing approved by Owner automatically. The Owner to send his comments, if any, within 6 days after Builders reminder.The Builder to give answer for Owner's comments within 14 days from the date of receiving. If the Builder fails to answer, the Owner to deem that the comments

44、 have been automatically accepted.In the event that any of the already approved plans for the first vessel are same as those for the subsequent sister vessels, the Builder may leave out the submission of such plans for the subsequent vessels. In which case the plan to clearly state the name/yard num

45、ber of vessels.The builder to furnish three(3) copies of the final drawings and instruction books of the major machinerys and equipments to the OWNER at the delivery of the vessel. One (1) CR-ROM with all available finished plans and documents to be provided to the Owner.The scope of finished plans

46、to be in accordance with the "Final Drawing List" which to be submitted to Owner for approval.All finished plans including instruction books/manuals to be written in English, except those attached with the equipment from abroad.Two (2) copies of each following drawings to be submitted on b

47、oard for passing through Suez and Panama Canals:General Arrangement Plan Capacity plan Engine Room Arrangement with Machinery List Midship Section Sounding Table for L. O. & F. O. TanksDamage control plan The following plans to be provided in frames and placed on board at such locations as desig

48、nated by the Owner's representative:General Arrangement One (1) copyCapacity plan with Deadweight ScaleOne (1) copyManeuvering characteristics diagram with time and distance, One (1) copyFire control plan with life saving appliance in color coding One (1) copyOil transfer procedures as per USCG

49、One (1) copySafety radio telegraphy certificate One (1) copyInstruction of Life Jacket and immersion suitsOne for each deck2-7SUB - CONTRACTORS Ordering of materials, machinery, equipment and other components to comply with the Specification and Makers List.2-8OWNER'S SUPPLIED ITEMS Following it

50、ems to be furnished and supplied by the Owner at their own expense, and installed on the vessel by the Builder. The Builder to provide sheltered and secure storage, handling in storage and handling on-board.· Tow line and mooring ropes in excess of the Specification· All air tools, hoses,

51、steel wires, etc. other than those mentioned in the Specification· All charts, nautical and radio station books, house flag and national flag· All consumable stores · All medicine and medical equipment except those for life boat and rescue boat.· Recreation equipment such as Ster

52、eophony, Video tape recorder and TV etc. and stationery other than mentioned in the Specification· Painting and pictures· Boatswain's and carpenter's tools over and above the Builders standard · All bedding and linen (pillows, blankets, sheets, covers, etc.) but excluding matt

53、resses.· All napery (serviettes, table clothes, etc.)· All cook's and steward's utensils (crockery, cutlery, silverware, earthenware, glasses, pots, pans, etc.)· Firemens outfit addition to the Rule requirement.· Typewriters, copy machine, computers, fax machine and other office machines.· Loose lashing/securing fittings for cargoes· Suez Canal searchlight, but one foundation in s