文本讲义说明measured report3template

1、CS11_Fully measured ReportProject Name Part Number CAD NumberProduct Name:CS11:_013: LATCH REINFORCEMENTSupplier: 上海天轼VCC Material standards : VDA 239-CR240LA Actual Material : CR240LAThickness: 1.2mmCoating thickness : GI50/50-U Detection time :2016/11/02CHECK RESULT 检查结果CHECK DATE检测日期OK.RATIO2016-

2、8-19Part codeP1P2P3TOTAL全OK Ratio100%100%100%OK Points828282Total Points828282SURF.型面OK Ratio100%100%100%OK Points464646Total Points464646TRIM修边OK Ratio100%100%100%OK Points303030Total Points303030HOLE孔径OK Ratio100%100%100%OK Points161616Total Points161616RPS InformationStep 1 : Surface CheckingRati

3、onalDMIS(TM) External-Array Software, Inc第 1 页西安测量-C7365西安测量RationalDMIS(TM) External-Array Software, Inc第 2 页西安测量-C7365西安测量RationalDMIS(TM) External-Array Software, Inc第 3 页西安测量-C7365西安测量Step 2 : Trim CheckingRationalDMIS(TM) External-Array Software, Inc第 4 页西安测量-C7365西安测量RationalDMIS(TM) External-

4、Array Software, Inc第 5 页西安测量-C7365西安测量Step 3 : Holes PositionRationalDMIS(TM) External-Array Software, Inc第 6 页西安测量-C7365Step 4 : Hole size CheckingRPS1安装孔 1安装孔 2安装孔 3安装孔 4安装孔 5安装孔 6安装孔 7nominal7.0(00.15)7.0(00.15)8.0(00.22)8.0(00.22)14.4(00.27)14.4(00.27)7.0*12(00.22) (-0.50.5)7.0*12(00.22) (-0.50.

5、5)actual7.107.118.078.0814.6114.587.09*12.187.06*12.16deviation00000000nominalactualdeviation安装孔 3安装孔 2安装孔 1RPS1安装孔 7安装孔 6安装孔 4安装孔 5Step 5 : ThinningREPORT CHECKING THINNESMeasure thickness request: 1.20.05 mmactual thickness 1.19 mmLIMITS MAX : 22%11.172163785421.1631.1541.1851.1761.1871.1881.14151

6、6THINNING MAX3.3%Step 6 : Appearance CheckingAppearance Checking 外观检查NO判定标准Control standard检验Methond判定OK、NG、N/APicture1零件是否正确？ Is the rignt part?Visual 目视OK2变薄率是否料厚20%范内THINNING MAX no more 20%Venire caliper 游标卡尺OK3是否有开裂、暗裂？ No crack,deformationVisual 目视OK4毛边、毛刺、尖角是否0.3mm 范围内？ glitches, indentation,

7、damaged,Venire caliper 游标卡尺OK5是否有模痕、压伤（无手感可接受）？ No roughness detect with the handwith the handOK6是否有拉伤、划伤？No degradation or deformation手触 with the handOK7是否有起皱、变形（装配面平面度需0.2MM 以内）？No crack,deformationVisual /Venire caliper目视/游标卡尺OK8是否有生锈？Rust?Visual 目视OK9字印是否正确、明显且无手 感？Marking information crrect ?Visual/ with the hand目视/手触OK10报告公差是否与 3D 公差相符？ Report tolerance is the same with 3D?检查 checkingOK11零件定位是否与检具定义相符？ PRS is the same with gauge?检具gaugeOK12料差是否超过公差带的 50%？ Trim