ANTCOR 24G 超级无线终端机（蚂蚁战车）用户使用手册_UG_CN

1、 封面沿用现在的wifirobin的封面，版本号改为2.4 GHz SUPER WIRELESS TERMINALPart One: Product feature Compatibility: Win 98, Win ME, Win Vista, Win 7, Linux, MAC OSXstandard, use OFDM technology. Wireless standard: AP WDS, Station WDS, AP, Repeater model Network model: Support Bridge, Router 3G network support: USB in

2、terface with EVDO, WCDMA, and TD-SCDMA fully supports MODEM Intelligence free drive: Wireless drivers and software, LCD display, automatically search the wireless signal, one key link Wireless rate: -4M/ 48M/ 36M/ 24M/ 18M/ 12M/ 9M/ 6M-11M/ / 2M/ 1M Wireless security: SSID broadcast control, MAC add

3、ress access control, WEP 64/128/152 encryption, WPA, 802.1X, TKIP, AES encryption and security mechanism Network security: Built-in firewall, support IP filter, domain name filter and MAC address filter WEB management: Multi languages configuration interface, regular free software upgrade Other func

4、tions: Support (UPNP), DDNS dynamic domain nameDevice AddressUser name: adminPassword: admin.二LCD CONFIGURATION2.1 Booting up the deviceConnect the antenna to the Wifirobin, usb cable and LAN cable to both Wifirobin and computer, booting up the device, after the power indicator light, LAN light and

5、AIR light are on, the menu will be shown.2.2 Menu is as follow, Device Info <Wireless InfoWireless Scan Factory Reset2 Device information As to the device information, please take a look at the software version, IP address.Firmware Ver <IP Address2 Wireless informationDisplay wireless signals

6、strength-31 dBm2 Wireless scanChoose WIRELSS SCAN, press ok, it will automatically searching for the wireless signals near around Scanning Aps . . . Wait for a while, it will show the hacked networks below: 2W OPN 45 <wiFi WEP 36airlive WPA 22robin OPN 16Above information are SSID, encryptions an

7、d signal strengthFor example： network name robin stands for SSID，OPN stands for encryption，16 stands for the signal strength；、OPN means non-encryption；、WEP means WEP encryption；、WPA means WPA encryption；、16 stands for signal strength, the larger the better; suggest to choose the signal above 10；、cho

8、ose OPN non-encryption, press OK, will show AP：connected successful；、choose WEP encryption, press OK then auto-hacking, if succeeds, it will connect to AP, if not, it will show the failure information.、After hacking, it will automatically connect to the wireless router and transfer to SSID model, th

9、at is, SSID is DD-link，password is 123456782 Auto-hacking process Decoding LV7AP：Snifferingneed at lease 20 minutes!IVS：xxxxxIVS：during the auto-hacking, grasp the AP packets digits, the stronger the hacked signals, the easier to crack the passwords. IVS reached to 200W-400W will be succeeded.Succes

10、s LV7 , AP：connected successfulSuccessful cracking information：Failure cracking information：ERROR IN FAKE Auth.2 Reset the factory settingsIf there are some unknown problems or after you upgrade the software that makes your Wifirobin not working, you have to reset the factory settings.Choose FACTORY

11、 RESET on the menu, press OK, reset factory settings, default address: is 192.168.4.20, user name: admin, password: adminDevice Info <Wireless InfoWireless Scan Factory Reset <OK < CANCEL 三、WEB PAGE CONFIGURATION3.1 Local IP settingsChange your network settings to IP address3.2 Open up your

12、 internet browser and access to , login with the username: admin and the password: admin You will see a pop-up window similar like below picture： Before cracking (see above)After cracking (see above)3.3 Wireless Mode introduction 1）、Wireless mode：support STATION, STATION WDS, ACCESS POINT, ACCESS PO

13、INT WDS, note that ESSID will be only appeared after you choose STATION option. 2）、ESSID、country code、mode、channel spectrum width, channel shifting、output power、data rate； 3）、Wireless security：include WEP、WPA、WPA- TKIP、WPA-AES、WPA2、WPA2-TKIP、WPA2-AES，see picture below：3 Station Mode settingsEnter in

14、to LINK SETUP tab, choose STATION as a wireless mode, and apply the change. See picture below,How to connect the Wifirobin with ESSID: click SELECT option, you will see a pop-up window as below, press SCAN button, it can automatically search for the wireless signals near around.Choose the ESSID you

15、want, apply the change then you can be connected. If your wireless network is encrypted, you need to fill in the corresponding password at the WIRELESS SECURITY tab, see the system information and tools options, drop-down the menu, you will see the Align antenna DB, see below picture.Take a look at

16、the ALIGN ANTENNA window below,Note that -96dBm is the signal between Wifirobin and ESSID3 ESSID MODE settingGo to the LINK SETUP tab, choose STATION, enable REPEATER, and apply the change. Then go to the NETWORK tab, choose ROUTER as a network mode, set your REPEATED ESSID and WPA PRESHARED KEY as

17、you want, see below： Go to NETWORK tab to choose ROUTER as a network mode.3.3.3 3G wireless router mode settingsIf using 3G function, you need to use the wall charger for the power supply. Note that the wall charger is not included in the package; please contact the official site to buy the charger.

18、Go to the NETWORK tab, choose the network mode BRIDGE, enable 3G, enable DHCP server, apply the change, then you can surf online by using 3G.Note： 1）、Wifirobin support 3G network card；2）、3G network card has been connected to the device；3）、Wifirobin IP choose STATIC status, otherwise you cant access

19、to the device. See below, Wifirobin 1.78V support 3G network card styles list,ManufacturerModelNetworkAW54-SCHUAWEIEC169EVDOOKEC169CEVDOOKEC1260EVDOOKEC1261EVDOOKZTEAC2726EVDOOKAC2736EVDOOKAC2746EVDOOKTlaytech TUE800EVDOOK3 Wireless router PPPoE settings Go to the NETWROK tab, choose ROUTER as a Net

20、work mode; at LAN NETWORK SETTINGS, choose PPPoE as LAN IP ADDRESS, and fill in the corresponding PPPoE user name and PPPoE password. At WLAN NETWORK SETTINGS, fill in the corresponding address, enable DHCP server, and apply the change. 3.3.5 Wireless router settingsWifirobin can be used as a wirele

21、ss router, go to the LINK SETUP tab, choose the wireless mode ACCESS POINT; then go to the NETWORK tab to choose the ROUTER as a network mode 3.4 How to set the hacked informationLets say, if Wifirobin hacked a password 31：32：33：34：35 that works very well, and if it hacked another one or you reset t

22、he factory settings and you need to restore to the one that you hacked previously, no need to hack again, please follow the settings below,Go to the LINKUP tab to choose STATION as a wireless mode, take a look at ESSID and WPA PRESHARED KEY, enable repeater, Choose network mode ROUTER： Change and apply the settings： Re