用英文介绍模具的组成一_第1页
用英文介绍模具的组成一_第2页
用英文介绍模具的组成一_第3页
用英文介绍模具的组成一_第4页
用英文介绍模具的组成一_第5页
已阅读5页,还剩2页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、This trial version can use only a part of item.Function of Major PartsYou will learn about the names and functions of major parts used for an ejection system.A push back pin and a coil spring are used for regular molds, whereas a push back pin and a gas spring are sometimes used for large size molds

2、.This figure illustrates an example of a large mold. Ejector Stopper (Stroke End Pin) A block that stops an ejector plate from going forward stop pinSprue Lock PinsA pin has the edge of which is undercut to pull a part in mold opening and remove a sprue from a sprue bush.After mold opening, this pin

3、 will function as an ejector pin and ejects the sprue from a aprue bush. Also it releases gas contained in molten plastic.Ejector PlateAlso called a push plate. A plate that supports an edge of an ejector pin or a push back pin to eject a part from a mold.It is ejected by an ejector device of a mold

4、ing machine, and returned to the original position when the edge of a push back pin collides with a cavity plate during mold clamping.Stop PinsA stopper installed to keep an ejector plate horizontal or prevent the ejector plate from retreating too far and damaging a core adaptor plate.Ejector Guide

5、Pins / Ejector Guide BushAn ejector guide pin is also called a push plate guide pin and functions as a guide for sliding of an ejector plate.Because an ejector guide bush slides, a hard material is used.An ejector guide bush is also called a push plate guide bush. It is a cylindrical part used to de

6、termine the position by matching the ejector guide pin.Push RodsA shaft linked to the force (hydraulic or mechanical) of the molding machine in order to get the ejector plate to work.Gas Spring / Gas Spring HolderA gas spring forcibly pushes back an ejector plate. The strength of the spring is adjus

7、ted by adjusting the filling pressure.When using a gas spring, make sure to avoid high temperature (heat may expand gas, deteriorating the original functions of a gas spring).Calculating Filling PressureTo figure out filling pressure (P) from early load (Wo): P = 100 * Wo /C (C: constant)To figure o

8、ut corresponding spring constant (K) from filling pressure (P) and gas spring constant (G):K =G * P / 100To figure out force by displacement (x) from the top D.C. of the piston rod (W):W = P (Gx + C)* See the catalog of each manufacturer for constant (C) and gas spring constant (G). A gas spring holder is a block used to fix

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论