(完整版)缸盖线常用英文汇总

1、缸盖线常用英文词汇冷去卩装置cooli ng device 反应室 reactive cell (chamber) 精度 accuracy ( precision) 算术平均值 arithmetic average 防漏 leak proof 油道 oil duct 润滑 lubricatio n 缸盖散热片cylinder head fin 进气和排气系统 in take and exhaust system推杆 push-rod气门室盖 valve chamber cover 气门导管valve guide 气门口 valve port 气门座valve seat气门座镶圈(嵌镶式气门座圈

2、)valve seat in sert(valve seat ring)气门座锥角 valve seat angle 气门座宽度 valve seat width 气门挺杆 valve tappet(valve lifter) 气门杆导管stem guide气门工作面valve face进气门 in take valve (suctio nvalve,inlet valve)排气口 exhaust port 排气门 exhaust valve 进口凸轮in let cam 排气凸轮exhaust cam 凸轮轴轴颈 camshaft bearing journal 凸轮轴轴承camshaft

3、bearing 凸轮轴camshaft 凸轮cam曲轴油道 cran kshaft oil passage 凸轮轴 轴承座 camshaft bearing bush seat燃烧室 combusti on chamber 夕卜径 major diameter 中径 pitch diameter 内径 minor diameter 止推面 thrust face 传感器 sensor transducer加工气门座圈和导管孔Bore Seat pockets and Ream Guide hole加工气门座圈和导管孔Bore Seat pockets and Ream Guide hole预清

4、洗Pre-Wash试漏Leak test压装座圈和导管Press-i n Seats and Guides精加工顶面，前后端面Finish mill cover, front, rear face精加工顶面，前后端面Finish mill cover, front, rear face去前后端面毛刺Brush front face, rear face去前后端面毛刺Brush front face, rear face去进排气面毛刺Brush in take face, exhaust face去进排气面毛刺Brush in take face, exhaust face精铰挺柱孔Finish

5、 ream tappet holes精铰挺柱孔Finish ream tappet holes中间清洗Mid wash凸轮轴盖装配Cam cap assembly精铰火花塞孔Ream Sparkplug hole精铰火花塞孔Ream Sparkplug hole精加工排气门座圈，导管孔Finish Exhaust seats and guides精加工排气门座圈，导管孔Finish Exhaust seats and guides精加工进气门座圈，导管孔Finish in take seats and guides精加工进气门座圈，导管孔Finish in take seats and gui

6、des去凸轮轴孔毛刺Brush Cam Caps去凸轮轴孔毛刺Brush Cam Caps最终清洗Final wash终试漏Fin al leak test目视检查Visual check下线Un loadi ng三坐标测量工位CMM缸盖线常用英文句子中文英文凸轮轴孔有砂眼Porosities was found on camshaft hole挺杆孔有砂眼Porosities was found on tappet holeF1000面有砂眼Porosities was found on F1000凸轮轴盖有砂眼Porosities was found on the camshaft cov

7、er面有直径超过1mm勺砂眼On F1000 There is a porosity which diameter larger tha n 1mm凸轮轴孔、挺杆孔、火花塞孔有许多细 小砂眼Porosities were found on F2000, tappet, spark plug hole, and water plug hole面水堵孔有砂眼Porosities were found in water stop hole on F6000# 2408座面有气孔Blowhole was found on #2408 seatF5000面缺料In sufficie nt stock w

8、as found on F5000油（水）道试漏不合格Failed on oil (water) gallery leakage test ingF1000面加工余量不足Machi ning Allowa nee is in adequate无法打标Failed in marki ng进气孔分隔柱铸造不合格The separated colu mn of in let failed in cast ingF4000面的支撑脚有缺陷Support feet is flawed挺杆孔有裂纹Flaw was found in the tappet hole燃烧室平均值过大Combusti on ch

9、amber average is too largeF5000止推面缺料Starved feed ing on thrust face通知SQP要求供应商改进毛坯SQFrequired suppliers to improve the rough part排气角超差Exhaust-a ngle is unq ualified面有划伤Scratch was found on the surface漏压导管，座圈Failed in pressuri ng the guides and seats由于设备故障漏压水堵盖和钢球Failed in pressuringthe water leakage

10、andblock in g-Ball清洗机夹伤The part was injury after worked in the Cleaning Machi ne更换新的刀具Replace a new tool对机床进料工装修磨Grind the feed ing machi ne frock对水堵进行返修后重新压装Re-pressuri ng the part after re-fit the water pluggi ng进气导管直径超差In take guide is unq ualified凸轮轴孔有刀痕Tool mark was found on camshaft hole在加工过程中T151断刀Tool broke in the mach ining进气座圈角度偏大Inlet seat an gle is too large换刀首件导管内孔超差The guide hole of first part is unq ualified after replaci ng a new tool工装的表面有毛刺Burr was found on the surface of the frock设备涂胶阀损坏Equipme nt adhesive valve was damaged设备异常Equipme nt was abno rmal工装上有铝屑aluminum l