塑胶类英语词汇大全重点讲义

1、废料粉碎机-scrap grinder 顶出板,脱模板-stripper plate 应力龟裂-stress cracking 环境应力龟裂试验-environmental stress cracking test 行程,衝程-stroke 注道,注道料-sprue 注道衬套,浇口衬套-sprue bush 成形压力,模製压力-molding pressure 成形温度,模製温度-molding temperature 成形循环,成形週期-molding cycle 成形时间,模製时间-molding time 成形收缩,模压收缩-mold shrinkage, molding shrinka

2、ge 窄浇口,限制形浇口-restricted gate 剪切强度,抗剪强度-shear strength 增亮剂-brightening agent,optical brightener,optical whitening agent 加速试验-accelerated test 加速老化-accelerated ageing 塑性变形-plastic deformation 塑性流动-plastic fiow翘曲-warp(ing),warpage 抗臭氧性-ozone resistance 抗臭氧试验-ozone resistance test 耐天侯性-weatherability,we

3、ather resistance 耐光性-light resistance,light fastness 天侯老化试验-weathering test 耐酸性-acid resistance 耐衝击性-impact resistance 褪色-fading,discoloration 耐蚀性-corrosion resistance 拉桿,导柱-tie-bar 拉桿间距-tie-bar distance 多模穴模具-multi-cavity mold 双色射出成形-double-shot molding 超音(声)波镶嵌-ultrasonic inserting 超音(声)波焊接-ultras

4、onic welding 顶出,脱模-ejection 顶出组合-ejector 顶出板-ejector plate,knock-out plate 顶出桿,脱模桿-knock-out bar,ejector rod 无光面-dull surface 低压射出成形法-low pressure injection molding 硬度计-durometer 电镀-electroplating,electrodeposition 电铸模具-electroformed mold 公差,容差-tolerance 冷料-cold slug 冷料井,冷料窝-cold slug well 回程销,覆归销-s

5、urface pin 冷热骤变试验-thermal shock test 热应力龟裂-thermal stress cracking,TSC 侧向浇口-side gate 侧向模蕊(心型)销-side draw pin 砂磨-sanding 喷砂,打砂-sand blast 修饰,涂饰,打光-finishing 自断浇口,剪切浇口-shear gate 紫外线-ultraviolet, UV 紫外线稳定剂-UV stabilizer 紫外线吸收剂-UV absorber 压花-embossing 压花机-embossing machine 喷霜,起霜-blooming exudation 鯊皮

6、斑-shark skin 射出压力-injection pressure 射出成形-injection molding 射出成形机-injection molding machine 射出成形模具-injection mold 射出装置-injection unit 射出速度-injection speed 射出喷嘴,注料嘴-injection nozzle 射出容量-machine shot capacity 射出率(量)-injection rate 煮沸试验-boiling test 充填不足,缺料-short shot 手动模具-hand mold,loose mold 手动油压机-h

7、and press 缩窝,凹孔-shrinkage pool 衝击试验-inpact test 衝击强度-impact strength 烧结法,粉铸法-sintering 烧结成形法-sinter molding 模板-mold plate 注射,射料-shot 硅橡胶-silicone rubber 真空成形-vacuum forming 珠光顏料-pearlescent pigment 浸渍涂装-dip coating 人造皮革-artificial leather嵌件-insert 嵌件销-insert pin 气胀真空成形-air assist forming 空气隙-air gap

8、 空气顶出-air ejection 永久伸长-permanent elongation,tension set 永久变形-permanent set,permanent deformation 蚀刻,侵蚀-etching 应力-stress 应力鬆弛-stress relaxation 应力龟裂-stress cracking 应力集中-stress concentration 应力断裂,应力破坏-stress rupture 应力.应变曲线-stress-strain curve 应力.应变图-stress-strain diagram 托板,模板-retainer plate 硬度-ha

9、rdness 合模机构-mold clamping mechanism 合模力,闭模力-locking force,clamping force 开模力-mold opening force 悬臂梁-cantilever beam 润滑剂-lubricant 模具-mold,Tools,Tooling 模温度控制器-mold temperature controller 模具尺寸-mold size 加热管套(料筒)-heating cylinder 加热板-heating plate 凸轮-cam 玻璃纤维-glass fiber,fibrous glass 玻璃纤维强化热塑塑胶-fiber

10、 glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP 玻璃纤维强化塑胶-glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP. 感光聚合物-photopolymer,photo-sensitive polymer 镜面抛光-mirror polishing 龟裂-cracking 龟裂-crack 颗粒料-granule 石墨-graphite 石墨纤维-graphite fiber 间隙, 隙距-

11、clearance 模蕊,蕊片,蕊线,蕊孔-core 成孔销,模蕊销-core pin 成孔销托板-core pin platephenolic resin 酚醛树脂 plastic 塑胶 polyacrylic acid 聚丙烯酸PAP polyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacr

12、ylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM polyphenylene oxide 聚硫化亚苯 polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯 polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVApolyvinylbuty

13、ral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物 silicone resin 矽树脂 thermoplastic 热塑性 thermosetting 热固性 thermosetting plastic 塑胶 unsaturated polyester 不饱和聚酯树脂入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate

14、水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples

15、 插头： connector plug 插座： connector socket 密封/封料： seal运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：

16、ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core in

17、sert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die sp

18、ring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting surface support balance 模排气：parting li

19、ne venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper ins

20、ert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode compre sion molding压缩成型 flash mold溢流式模具plsitive mold挤压式模具 split mold分割式模具 cavity型控 母模 core模心 公模 taper锥拔 leather cloak仿皮革 shiver饰纹 flow mark流痕 welding mark溶合痕 post screw insert螺纹套筒埋值 self tapping screw自攻螺丝 striper plate脱料板 piston活塞 cylinder汽缸套 chip细碎物 handle mold手持式模具 encapsulation molding低压封装成型、射出成型用模具 two plate两极式（模具） well type蓄料井 insulated runn