IPT项目配置手册--------voicemail

1、IPT项目配置手册1 配置CUCM1.1 修改Hostname为IP1.2 配置CM1.3 配置CM Group1.3 启动服务1.4 配置NTP1.5 配置Region1.6 配置Media resource1.7 配置SRSTvoice register global mode srst system message * CCM Crashed :-( * max-dn 200 max-pool 58!voice register pool 1 id network 172.16.200.0 mask 255.255.252.0 preference 1 incoming called-n

2、umber . dtmf-relay sip-kpml codec g711ulawvoice service voip ip address trusted list ipv4 172.16.200.0 255.255.252.0 allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip supplementary-service h450.12 fax protocol t38 version 0 ls-red

3、undancy 0 hs-redundancy 0 fallback none h323 modem relay nse codec g711ulaw gw-controlled sip bind control source-interface GigabitEthernet0/0 bind media source-interface GigabitEthernet0/0 registrar server expires max 600 min 300!1.8 配置Device Pool1.9 配置Gatewayccm-manager config server 172.16.200.11

4、 172.16.200.12 ccm-manager config1.10 配置Translation Pattern1. 1.11 配置Partition1.12 配置CSSCalling Search SpaceRoute Partition1Route Partition2RoutePartition3Route Partition4RoutePartition5CSS-EmergencyPT- EmergencyCSS-LocalPT- EmergencyPT-InternalPT-LocalCSS-NationalPT- EmergencyPT-InternalPT-LocalPT-

5、NationalCSS-InternationalPT- EmergencyPT-InternalPT-LocalPT-NationalPT-International1.13 配置Route Group1.14 配置Route List1.15配置Route Pattern注：Route Pattern下的 Allow Overlap Sending要打勾，否则只能拨打市内电话，无法拨打长途电话。1.16 配置Voice Mail1.17 调整相关时间参数1.18 配置电话机1.19 配置Meet-Me1.20 配置备份选择Backup选项中的Backup Device 点击add new选

6、择Backup选项中的manual backup立即进行备份2 配置Unity Connection2.1 配置PhoneSystemAppSyn在CUCM创建，密码也是AppSyn2.2 配置Unity Connection集群参数2.3 配置前台AA、在CUCM 中配置一个Hunt Pilot配置Translation Pattern将总机转到3260，进入Unity Connection2.4 配置E1提示音过程与配置前台AA一致在CUCM上做以下配置l Trunk-CNNS-VM l 创建2个Route Group RG-CNNS-PSTN；RG-CNNS-HK；RG-CNNS-VMl

7、 创建1个Route List,调用两个Route Group，当PSTN的链路不可用时，呼叫会走下面的RG-CNNS-VM。l 在的配置下面，配置VM号码使得呼叫转向VM，从而播放提示音并让用户可以按键操作。 2.5 创建Voice Mail 用户配置密码3 配置EXSI3.1 编辑网卡跟交换机做Port-channelFor CNNS2F-Core-4510R-001interface Port-channel20 description UCS-1 switchport switchport mode trunkinterface GigabitEthernet1/9 descripti

8、on UC1_LAN1 switchport mode trunk channel-group 20 mode oninterface GigabitEthernet1/10 description UC1_LAN2 switchport mode trunk channel-group 20 mode onendinterface Port-channel21 description UCS-2 switchport switchport mode trunk!interface GigabitEthernet1/11 description UC2_LAN1 switchport mode trunk channel-group 21 mode oninterface GigabitEthernet1/12 description UC2_LAN2 switchport mode trunk channel-group 21 mode onend3.2 创建网络4 配置PLM管理license4.1 添加管理对象4.2 查看