Harness training_第1页
Harness training_第2页
Harness training_第3页
Harness training_第4页
Harness training_第5页
已阅读5页,还剩4页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

1、1 Agenda for Harness/Fall protection equipment introduction and self-assessment Section 1: Section 2: Warning and limitation Section 3: Component information Section 4: Typical connection and installation Section 5: what need be inspected Section 6: other important information Section 7: self- asses

2、sment and survey 2 Harness/Fall protection equipment introduction and self-assessment Section 1: It is the employers responsibility to ensure all user are trained in the proper use, inspection ,and maintenance of fall protection equipment All equipment must be inspected before each use according to

3、manufacturers instructions; all equipment must be inspected by a qualified person on a regular basis Any product exhibiting deformities or deterioration must be discarded immediately 3 Harness/Fall protection equipment introduction and self-assessment Section 1: The rescue plan shall be in place and

4、 the means at hand to implement it when using this equipments Environment hazards should be considered when selecting. Equipment must not be exposed to chemicals may produce harmful effect Dont allow equipment to come in contact with anything that will damage it, including but not limited to sharp/a

5、brasive/high temperature surface/heat source/electrical hazards 4 Harness/Fall protection equipment introduction and self-assessment Section 2: Warning and limitation For use by ONE person only. Design working load is 140.6kg. When used with a shock absorber, self- retracting lifeline are rated to 1

6、81.4kg Dont use the device if it does not retract; dont allow lifeline to become slack 5 Harness/Fall protection equipment introduction and self-assessment Section 3: Component information Part A: Tie-off point/anchor point: must be capable of supporting 5000 lbs( 22.2KN=2.244MT) Part B: Full-body h

7、arness should be worn in all situations where workers are exposed to a potential free fall Part C: whether it is a shock-absorbing lanyard or self-retracting line , they are designed to reduce fall arresting force 6 Harness/Fall protection equipment introduction and self-assessment Section 4: Typica

8、l connection and installation Figure1: Connect the lifeine/lanyard end connector to the back D-ring Figure 2: Connect the retractable unit to the anchorage Figure 3: The reverse connection with figure 1 and figure 2 Figure 4/5: Typical installation 7 Harness/Fall protection equipment introduction an

9、d self-assessment Section 5: what need be inspected Lanyard/lifeline Braking mechanism Snap hook Anchorage connector Load impact indicator For more details, see referenced document 8 Harness/Fall protection equipment introduction and self-assessment Section 6: other important information Lanyard wil

10、l be shock-absorbing type, six feet or less in length All connector (i.e. snap hook) will be locking type Personal fall arrest system shall be rigged such that an employee can neither free fall more than 6 feet, not fall into any lower object (s) Vertical lifeline must have a breaking strength speci

11、fied by the manufacture as 6000lbs. only one employee may be attached to any one vertical lifeline Tie-off point, preferably at or above shoulder level 9 Harness/Fall protection equipment introduction and self-assessment Section 7: self- assessment and survey Identify what kinds of fall protection equipment used Confirm if the training course and training plan in place Confirm if the rescue plan

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论