MA5605配置操作手册

1、MA5605配置操作手册相关命令：show timeshow versi onshow board 0show runnin g-c onfigi：改名字MA5605(c on fig)#host name xiaowei 2:改用户密码MA5605#user passwordold password: adm in（改后新密码，如果不需要设置此步不需要做） New password( Con firmnew password:admi nmin3:改时间MA5605#time（一般不用配置）4. 进入LAN配置模式设置 LAN端口状态int lan 0/0MA5605(co nfig-LAN

2、-0/0)#port modetagged,u ntagged:taggedn egotiate ,non-n egotiate:non-n egotiatefull-duplex:full-duplex100m:100mSet successfully.5. MA5605(config-LAN-0/0)#vlan %d (业务 VLAN)1-4095:1554Add VLAN successfully, VLANID =MA5605(config-LAN-0/0)#vlan %d (管理 VLAN)1-4095:1000Add VLAN successfully, VLANID = 5.设置

3、VLAN （打开带内通道）MA5605(config)#nms1-4095:1000 (网关 vlan )Are you sure to set the inband VLAN to 1? (y/n) n:y6. 设置级联转发 VLAN ( 注意如果是级连要此步，不是侧不要MA5605(config-LAN-0/0)#cascadeforward,number:number0-3:1Set cascading number successfully.MA5605(config-LAN-0/0)#cascadeforward,number:forwardvlan,all:all1-4095:1-

4、4095:Set 16 cascading VLAN successfully.VLAN 和级联层数（设备分配的范围内。? 如果有级联设备，则上级设备需要设置转发(下级设备的) 设置 FE 接口级联转发功能 ”)；? 级联 MA5605 下级的 VLAN ID 必须在上级 MA56057. 设置设备 IP 地址MA5605(config)#at mlan ip-address ethernet :218.92.157.150:255.255.255.248Set successfully8. 配置到上连设备的系统路由MA5605(config)#at mlan ip-route :0.0.0.

5、0:0.0.0.0 :218.92.157.145Add route successfully.9. 配置可接受访问列表MA5605(config)#at mlan ip-access :218.92.157.145( 路游地址 ):218.92.157.137:255.255.255.255可把县局要维护的计算机、交换机地址配置进去）10. 设置 ADSL 线路模板参数e are neglected. 加模板 )WA_SL_MA5605(config)#adsl line-profile add 8During input,press Q to quit,then settings at t

6、his tim Select the line profile type 1-adsl 2-adsl2+(12) 1: (2 Will you set basic configuration for modem? (y/n) n:yNote: Setting to these mode of G992.35 will lead that the adsl ports that arenot support adsl2+ not be activated ADSL operating mode: 0: All(G992.13, G992.5, T1.413) 1: Full rate(G992.

7、1/3/5 or T1.413) 2: g.lite(G992.2) (ADLI can not support ) 3: T1.413 (ADLI can not support ) 4: g.dmt(G992.1/3/5) 5: g.hs(G992.13, G992.5, G992.5 is prior) 6: G992.1 7: G992.2 (ADLI can not support ) 8: G992.3 9: G992.5Please select (09) 0: Trellis coding 0-disable 1-enable (01) 1: Upstreamchannel b

8、it swap 0-disable 1-enable (01) 1: Downstream channel bit swap 0-disable 1-enable (01) 1: 0 Will you set channel mode? (y/n) n: yPlease select channel mode 0-interleaved 1-fast (01) 0: Will you set interleave delay? (y/n) n: y Max down streaminterleaved delay(0255 ms) 16: Max up streaminterleaved de

9、lay(0255 ms) 6: Please select formof transmit rate adaptation in downstream 0-fixed 1-adaptAtStartup 2-adaptAtRuntime (02) 1: Will you set noise margin for modem? (y/n) n:y(015 dB) 6:(06 dB) 0: (631 dB) 31: Target noise margin in down stream (015 dB) 6: Min noise margin in down stream Max noise marg

10、in in down stream(06 dB) 0:(631 dB) 31: Target noise margin in up stream Min noise m argin in up stream Max noise m argin in up stream Will you set parameters for rate? (y/n) n: y Max bit rate in dow n stream Min bit rate in up stream(3 Max bit rate in up stream(3 Please in put the profiles n ame :

11、9M Add profile 9 successfully.(3232000 Kbps) 32000: 7168 (323000 Kbps) 32:(323000 Kbps) 3000: 512（下行用户速率）（上行速率）12.激活ADSL端口MA5605(config)#interface adsl 0/1MA5605(config-ADSL-0/1)#detactivate allMA5605(c on fig-ADSL-0/1)#activateall:all1-20:513.设置从 ADSL 1 端口到 VLAN 10 的业务 PVC pvc adsl 1483b 1 off off 2 2 (批量生成)MA5605(co nfig)#pvcadsl,shdsl,la n:adsl(0)