模具工程中英文对照讲诉

1、模具工程中英文对照die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap 切边to bending 折弯to pull, to stretch 拉伸Line streching, line pulling线拉伸engraving, to engrave 刻印upsiding down edges 翻边to sta

2、ke 铆合design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin顶料销die plate, front board 模板padding block 垫块stepping bar 垫条upper die base 上模座lower die base 下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies 模具备品spring 弹簧bolt 螺栓plate 电镀mold 成型mate

3、rial for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected 进货待验PCE assembly production schedule sheetPCE 组装厂生产排配表model 机锺work order 工令revision 版次production control confirmation生产确认checked by 初审approved by 核准stock age analysis sheet库存货龄分析表on-hand i

4、nventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked待验或重工cause description 原因说明part number/ P/N料号item/group/class 类别prepared by 制表year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异

5、量good product/accepted goods/ accepted parts/good parts 良品 defective product/non-good parts 不良品 disposed goods 处理品on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM 放电机coil stock 卷料sheet stock 片料toler

6、ance 工差score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce 剪内边drag form 压锻差pocket for the punch head 挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge) 楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定位销round pierce punch=die button 圆冲子shape punch=die insert 异形子stock locat

7、er block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert 入块capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkalidipping脱脂main manifold 主集流脉be

8、zel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁 ; 消磁high-speed transmission 高速传递heat dissipation 热传rack 上料degrease脱脂rinse 水洗alkaline etch 龄咬desmut 剥黑膜D.I. rinse 纯水次Chromate 铬酸处理Anodize 阳性处理seal 封孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished prod

9、ucts 成品disposed products 处理品barcode 条码flow chart 流程表单assembly 组装stamping 冲压molding 成型spare parts=buffer 备品coordinate 座标dismantle the die 折模auxiliary fuction辅助功能poly-line 多义线heater band 加热片thermocouple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer 烘干机induction 感应induction light 感应光re

10、sponse=reaction=interaction 感应ram 连杆edge finder 巡边器concave 凸convex 凹short 射料不足nick 缺口speck 瑕疵shine 亮班splay 银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush 导色gouge 沟槽 ;凿槽satin texture 段面咬花witness line 证示线patent 专利grit 沙砾granule=peuet=grain 细粒grit maker 抽粒机cushion 缓冲magnalium 镁铝合金magnesium metal plate镁金

11、钣金lathe车mill 锉plane 刨grind 磨drill铝boring 镗blinster 气泡fillet 镶 ;嵌边through-hole formvoller pin formalitycam driver 铡楔通孔形式滚针形式shank 摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy 合金tungs

12、ten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator 滴定仪beacon 警示灯coolant 冷却液crusher 破碎机模具工程类plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型 (

13、抽凸 ,冲凸 )draw hole 抽孔bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字 (料号 )shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die struct

14、ure dwg 模具结构图material 材质material thickness 料片厚度press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙punch wt. 上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire

15、spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套模板类top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模 (凸模 )feature die 公母模female die 母模 (凹模 )upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下

16、模座bottom block 下垫脚bottom plate 下托板 (底板 )stripping plate 内外打 (脱料板 )outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块 (嵌入件 )deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定

17、位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块uppe

18、r mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块塑件 & 模具相关英文compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心 公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post

19、 screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head刨尖头slag wel

20、l 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar) （成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射

21、嘴sprue lock pin 料头钩销 (拉料杆 )slag well 冷料井side gate 侧浇口edge gate侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口 ; 溶渣各种模具

22、常用成形方式accurate die casting精密压铸powder forming粉末成形calendaring molding压延成形powder metal forging粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging冷锻press forging冲锻compacting molding粉末压出成形rocking die forging摇动锻造compound molding复合成形rotary forging回转锻造compression molding压缩成形rotational moldin

23、g离心成形dip mold 浸渍成形rubber molding橡胶成形encapsulation molding 注入成形sand mold casting砂模铸造extrusion molding挤出成形shell casting壳模铸造foam forming泡沫成形sinter forging烧结锻造forging roll 轧锻six sides forging六面锻造gravity casting重力铸造slush molding凝塑成形hollow(blow) molding中空 (吹出 )成形squeeze casting 高压铸造hot chamber die casting

24、 热室压铸swaging 挤锻hot forging 热锻transfer molding转送成形injection molding射出成形warm forging温锻investment casting精密铸造matched die method对模成形法laminating method被覆淋膜成形low pressure casting低压铸造lost wax casting脱蜡铸造matched mould thermal forming对模热成形模各式模具分类用语bismuth mold铋铸模landed plunger mold有肩柱塞式模具burnishing die挤光模lan

25、ded positive mold有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold活零件模具chill mold冷硬用铸模loose mold 活动式模具clod hobbing冷挤压制模louvering die百叶窗冲切模composite dies 复合模具manifold die分歧管模具counter punch 反凸模modular mold组合式模具double stack mold 双层模具multi-cavity mold多模穴模具electro

26、formed mold电铸成形模multi-gate mold复式浇口模具expander die 扩径模offswt bending die双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold反套制品模具plaster mold 石膏模blank through dies漏件式落料模porous mold通气性模具duplicated cavity plate复板模positive mold全压式模具fantail die扇尾形模具pressure die 压紧模fishtail die鱼尾形模具profile die轮廓模flash mo

27、ld溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold热流道模具prototype mold雏形试验模具ingot mold钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold半全压式模具shape

28、r 定型模套single cavity mold单腔模具solid forging die整体锻模split forging die拼合锻模split mold双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die切边模unit mold单元式模具universal mold通用模具unscrewing mold退扣式模具yoke type die 轭型模模具厂常用之标准零配件air v

29、ent vale 通气阀anchor pinangular pin锚梢角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button球塞套ball plunger定位球塞ball slider球塞滑块binder plate 压板blank holder防皱压板blanking die落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block缓冲块buster 堵口casting ladle 浇注包casting lug铸耳cavity模穴

30、 (模仁 )cavity retainer plate模穴托板center pin 中心梢clamping block锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母cooling spiral螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具

31、固定用零件die holder 母模固定板die lip模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin合模梢dozzle 辅助浇口dowel pin定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector

32、 plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core椿入蕊film gate薄膜形浇口finger pin指形梢finish machined plate角形模板finish machined round plate圆形模板fixed bolster plate固定侧模板flanged pin带凸缘销flash gate 毛边形浇口flask 上箱floating punch浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guid

33、e bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram压射柱塞inlay busher 嵌入衬套inner plunger内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin转向梢king pin bush主梢衬套knockout bar 脱模杵land 合模平

34、坦面land area 合模面leader busher 导梢衬套lifting pin起模顶销lining内衬locating center punch定位中心冲头locating pilot pin定位导梢locating ring定位环lock block压块locking block定位块locking plate定位板loose bush 活动衬套making die打印冲子manifold block歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bols

35、ter换模保持装置moving bolster plate可动侧模板one piece casting 整体铸件parallel block平行垫块paring line分模线parting lock set合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer

36、 plate 托料板return pin 回位梢riding stripper浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint滑配接头spacer block 间隔块spacer ring 间隔环spider

37、 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin圆柱销stripper bolt脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end bl

38、ock 行程止梢submarine gate 潜入式浇口support pillar支撑支柱 /顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢 / 锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machi

39、ne 搪孔机cnc milling machine CNC铣床contouring machine轮廓锯床copy grinding machine仿形磨床copy lathe仿形车床copy milling machine仿形铣床copy shaping machine仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine雕刻机engraving E.D.M. 雕模放置加工机form grinding machine成形磨床graphite machi

40、ne 石墨加工机horizontal boring machine卧式搪孔机horizontal machine center卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine冶具搪孔机jig grinding machine冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床 NC lathe NC车床NC programming system NC 程式制作

41、系统planer 龙门刨床profile grinding machine投影磨床projection grinder 投影磨床radial drilling machine旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine试模机turret lathe转塔车床universal tool grinding machine 万能工具磨床vertical machine center立式加工制造中心wire E.D.M.线割放电加工机模具钢材alloy tool steel合金工具钢aluminium alloy铝合金钢bearing alloy轴承合金

42、blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel热锻模用钢low alloy tool steel特殊工具钢low manga

43、nese casting steel 低锰铸钢marging steel马式体高强度热处理钢martrix alloy马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel镍铬钢prehardened steel 顶硬钢silicon steel sheet 矽钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough p

44、itch copper韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑胶覆面钢板表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体 /奥氏体bainite 贝氏体banded structure 条纹状组织barrel plat

45、ing滚镀barrel tumbling滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing磷酸盐皮膜处理box annealing 箱型退火box carburizing封箱渗碳bright electroplating辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing渗碳cementite 炭化铁chemical plating化学电镀chemical vapor depositio

46、n化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion扩散diffusion annealing扩散退火electrolytic hardening电解淬火embossing 压花etching 表面蚀刻ferrite肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing完全退火gaseous cyaniding 气体氧化法globular cementite球状炭化铁grain size 结晶粒度granolite treatment磷酸溶液热处理graphitizing石墨退火hardenability硬化性hardenability curve硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping热浸镀inductio