锂电保护板规格书

深圳嘉智电子有限公司 SHENZHEN JIAZHI CO.,LTD项目名称Project nameJZ-JY-0011研发版本Uncontrolled RevisionV1页次Page第9页 共9页文件编号Document No受控版本Controlled Revision实施日期Issued Date2014年11月18日产品规格书SPECIFICATION客户Customer客户型号Customer Model项目名称Project NameJZ-JY-0011文件编号Document NO受控版本Controlled Revision实施日期Issued Date编制Registered审核Checked审核Checked审核Checked批准Approved批准Approved修订记录Modified Record产品修订记录表Product Modified Record List版本Revision变更内容Modified Content责任人Principle日期Date标记Mark备注Note V1制样Sample making 一、 综述Outline本规格书适合于深圳嘉智电子有限公司研制的1串锂动力电池保护板，本产品严格满足ROHS规范等。This specification applies to the 1 serial-cells lithium-ion battery protection board manufactured by SHENZHEN JIAZHI CO.,LTD, which strictly conforms to the ROHS standard.二、应用范围Application锂充电电池包等。Applies to the lithium-ion rechargeable battery packs and so on.三 、电气特性Electronic characteristic（Ta=25）测试项目test item详细内容content最小值minimum典型值typical最大值maximum单位unit备注note参数配置CFG过充over charge单节过充保护over-charge protection for each cell4.2504.3004.350V单节过充保护延迟时间over-charge protection delay time for each cell0.82.0S单节过充保护恢复over-charge recover protection recover for each cell4.0504.1004.150V过放over discharge单节过放保护over-discharge protection for each cell2.3002.4002.500V单节过放保护延迟时间over-discharge protection delay time for each cell2060mS单节过放保护恢复over-discharge recover protection for each cell2.9003.0003.100V测试项目test item详细内容content最小值min典型值typical最大值max单位unit备注note过流及短路Over current& short circuit放电过流保护discharge over current protection 369A短路保护short circuit protection有YES放电过流保护延迟时间discharge protection delay time1020mS正常充电电流normal charging current1.8A正常放电电流normal discharging current1.8A均衡balance均衡开启电压balance start voltage/V均衡电流balance current/mA测试项目test item详细内容content最小值min典型值typical最大值max单位unit备注note参数配置CFG温度保护/充电temperature protection /charge过温保护over temperature protection/过温保护恢复over temperature protection recover/温度保护/放电temperature protection /dis-charge过温保护over temperature protection/过温保护恢复over temperature protection recover/测试项目test item详细内容content备注note恢复方式RecoveryMode放电过流保护discharge over current protection断开负载后恢复It will recover after cutting off the load短路保护short circuit protection断开负载后恢复It will recover after cutting off the load高温保护over temperature protection/过充保护over-charge protection低于过充恢复值under the over-voltage recover value过放保护over-discharge protection充电恢复Charging静态功耗sleep modeMAX：7uA内阻internalresistanceMAX：40m结构尺寸dimension13*0.6mm四、工作环境和贮存环境条件Working condition and storage condition工作环境条件working condition项目item标准standard备注note工作温度范围the working temperature range-30 85在此范围工作正常normally work相对湿度relative humidity5% 95%长期工作，无冷凝work long time, no condensing大气压atmospheric pressure86 106 KPa贮存环境条件storage condition温度humidity-40 95相对湿度relative humidity 75%大气压atmospheric pressure86kPa 106kPa五、连线示意图及连接步骤Linking diagram and connecting steps 1、充电接线方式the charging connecting method： 充电器负极接P-；P-connects to the cathode of the charging;充电器正极接B+；B+ connects to the Anode of the charging;2、放电接线方式 the discharging connecting method： 负载负极接P-；P- pads connects to the cathode of the loader; 负载正极接B+。B+ connects to the anode of the charging.3、注意事项notes：将电池和本保护板组合好以后，初次上电时，如果发现无电压输出,请用专用充电器充电激活。若仍有异常，请与厂家联系。After assembling the battery and the protection board, if there is no voltage output when your first power on, please charge the battery with the special charger and it will work normal.If there is still abnormal, please contact us.六、使用和组装的注意事项 The notes of using and assembling 1、焊接电池引线时，一定要小心，不可接错或反接。如发觉接错后，这块电路板有可能已经损坏，需要经过重新测试合格后才可以再次使用。Be careful and make sure not connect wrong or oppositely when weld the lead wire. It can be used after the re-test is ok because the PCBA may have been destroyed when the wrong connection.2、装配时BMS不要直接接触到电芯表面，以免损坏电芯。装配要牢固可靠。BMS do not touch the cell surface in order to prevent from destroying cell when you assembling. Make sure assembling stable and reliable.3、使用中注意引线头、烙铁等不要碰到电路板上的元器件，否则有可能损坏本电路板。Do not touch the components in the PCBA in order to prevent from destroying the board when use the wire, soldering iron.4、使用过程要注意防静电，防潮和防水等。Pay attention to the antistatic, damp proof, waterproof and so on.5、使用过程中请遵循设计参数及使用条件，不得超过本规格书中的值，否则有可能损坏本保护板。Make sure the design parameters and working condition which are under the value in the specification, or else may destroy the PCBA.七：环境物质要求 Environmental Requirements本规格书内容符合欧盟RoHS指令要求，有害物质含量符合以下标准：The specification subjects to the EU Directive about RoHS, and the hazardous substance conforms to the following standard.有害物质 hazardous substance基准 standardCadmium and its compounds: 镉(Cd)及其化合物 100PPMLead and its compounds: 铅(Pb)及其化合物 1000PPMMercury and its compounds: 汞(Hg)及其化合物 1000PPMChromium() and its compounds: 六价铬(Cr6+)及其化合物 1000PPM(非电镀)禁用(电镀) forbid platingPolybrominated biphenyls(PBBs): 多溴