自己设计的花键跨棒距的计算-2

渐开线内花键棒间距及反算齿槽宽,,,,,,,,

,,,,,,,,,

参数名称,代号,偶数齿参数值,奇数齿参数值,,求反渐开线函数公式,,,

模数,m,2,2.445,,"已知渐开线函数值为invα,求出其角度α值",,,

齿数,z,24,19,,αk=ACOS(sin(α(k-1))/(invα+α0)),,,

分度圆压力角,α,20,30,,α0=(3*invα)^(1/3),,,

分度圆压力角的弧度值,RAD,0.34906585,0.523598776,,按上述公式计算出α4后，用公式DEGREES（α4）就可得角度值,,,

分度圆渐开线函数值,invα,0.014904384,0.053751494,,示例,,,

变位系数,x,0,0.8,,"已知渐开线函数值为invα=0.0149043838673364,求出其角度α值",,,

量棒中心所在圆的压力角渐开线函数值,invαn,0.00275788,0.062625523,,先算出α0=（3*0.0149043838673364）^(1/3),,,

量棒中心所在圆的压力角,αn,11.52549528,31.43933217,,invα=,0.0149043838673364,角度值,函数DEGREES(GX)

量棒中心所在圆的压力角弧度值,RAD,0.201157841,0.548719861,,α0=,0.3549319491381200,,20.33610269996630000

基圆直径,Db,45.1052458,40.23121013,,α1=,0.3491126192766700,,20.0026796593107000

量棒直径,Dr,3.5,3,,α2=,0.3490658534034250,,20.0000001721486000

量棒中心所在圆的压力角余弦值,cosαn,0.979835894,0.853192936,,α3=,0.3490658503988650,,20.0000000000000000

奇数齿所用角的余弦值,cos(90/Z),,0.996584493,,α4=,0.3490658503988660,,20.0000000000000000

跨棒距,M最小,42.53346958,43.99265369,,,,,

,,,,,,,,,

最大棒间距,Mmax,42.75,43.99,,,注：绿色单元格部分是要填写的数据，其它颜色的单元格不必填写！,,

最小棒间距,Mmin,42.55,43.89,,,,,

任意压力角弧度值,αmax*,0.222953929,0.55739895,,,,,

,αmin*,0.202910676,0.545128275,,,,,

任意压力角渐开线函数初值,invαmax*,0.003769194,0.065933043,,,,,

,invαmin*,0.002831437,0.06129385,,,,,

实际齿槽宽最大值,Emax,3.190133082,4.02999547,,,,,

实际齿槽宽最小值,Emin,3.14512074,3.814481791,,,,,

,,,,,,,,,

渐开线外花键棒间距及反算齿槽宽,,,,,,,,

参数名称,代号,偶数齿参数值,奇数齿参数值,,,,,

模数,m,1.25,1.667,,,,,

齿数,z,18,19,,,,,

分度圆压力角,α,20,20,,,,,

分度圆压力角的弧度值,RAD,0.34906585,0.34906585,,,,,

分度圆渐开线函数值,invα,0.014904384,0.014904384,,,,,

变位系数,x,0.8,0.8,,,,,

量棒中心所在圆的压力角渐开线函数值,invαn,0.066408682,0.06367777,,,,,

量棒中心所在圆的压力角,αn,32.00653731,31.59963335,,,,,

量棒中心所在圆的压力角弧度值,RAD,0.558619458,0.551517644,,,,,

基圆直径,Db,21.14308397,29.76288438,,,,,

量棒直径,Dr,2.25,3,,,,,

量棒中心所在圆的压力角余弦值,cosαn,0.847987628,0.851730287,,,,,

奇数齿所用角的余弦值,cos(90/Z),,0.996584493,,,,,

跨棒距,M最大,27.1832458,37.82467336,,,,,

,,,,,,,,,

最大棒间距,Mmax,27.18,37.81,,,,,

最小棒间距,Mmin,27.03,37.65,,,,,

任意压力角弧度值,αmax*,0.769268882,0.757126302,,,,,

,αmin*,0.763963387,0.752951934,,,,,

任意压力角渐开线函数初值,invαmax*,0.198981894,0.187870366,,,,,

,invαmin*,0.194060383,0.184173582,,,,,

实际齿槽宽最大值,Emax,6.536143964,8.670884874,,,,,

实际齿槽宽最