总线ff卡件修复步骤

1、 Foundation Filed Bus Module RepairFF总线卡件版本升级需固件修复，前期需进行如下准备（此时已完成FF卡件在Ovation相关配置工作并两个网段端口与现场设备相连）：将新配置文件vxWorks和vxWorks.system拷贝至C:OvationVxWorksModulesFieldbusboot目录下，原先的文件，命名为vxWorks.orig和vxWorks.system.orig，并Downloading相应的控制器(配置文件在FF repair文件夹中)；在自己笔记本PC机上安装Cerberus FTP Server，并配置，步骤如下：运行Cerber

2、us FTP Server程序打开Configuration 选项，打开User Manager选中Add a New User添加一个用户名为“csb”新用户Password 设为“csb”在C根目录下建一个ftproot的文件夹,将rdp_m.out，Repair，rftp.out，rnet_m.out，vxWorksRepair拷贝到此文件夹（文件在附件1文件夹中）运行Cerberus FTP Server程序将PC机的网卡IP地址设置为，子网掩码设为，网卡网线与交换机相连打开Hyper-terminal，其配置如下：Properties - Connect To Tab - Confi

3、gureBits/second =38400Data Bits = 8 Parity = NStop Bits = 1Flow Control = NoneFF卡件需要串口线与自己笔记本PC连接，连接方法见下图所示：J7 Connector Pin Assignments1 TXD2 RXD3 DGND4 RXD5 TXDJ7 to DB9 PinoutJ7-P1 DB9-P2J7-P2 DB9-P3J7-P3 DB9-P5FF卡件的网口与交换机相连接卡件与笔记本PC机连接与否可在Hyper-terminal显示,连接成功 后会 出 现“Ovation Bus Module Boot - Re

4、v. 0D”，当CPU: CSB337 - Atmel AT91RM9200 (ARM)Version: VxWorks 6.3BSP version: 2.0/1Creation date: Jun 29 2009, 15:28:07Press any key to stop auto-boot.7 按任意键停止卡件自启动完成上一步工作后，可以对FF卡件进行修复，步骤如下：At the ”VxWorks Boot” prompt type “c” to change the boot optionsSet “Boot Device” to “emac0”Leave” processor nu

5、mber” as is (just hit enter)Leave “host name” as is Set “file name” to “vxworksrepair”Set “inet on ethernet” to an address on the subnet with the FTP Server, and that does not conflict with anything else on the networkLeave “inet on backplane” as isLeave “host inet” to the IP address of the FTP Serv

6、erLeave “gateway inet” to “.” (DOT removes the existing entry)Leave “user” as isLeave “ftp password” as isSet “flags” to “0” to enable ftp bootLeave “target name” as is Leave “startup script” as is Leave “other” as isAt the ”VxWorks Boot” prompt type” to boot. You should see the FTP Server respond t

7、o the FTP Boot requests made by the ELC/BUS module.注：此时FF卡将自行修复，当出现- Executing startup script host:/repair.scr.代表修复已完成。在装有Ovation系统的PC机上点击Ovation-Ovation Utilities打开Diagnostics,选择相应的控制器的FF卡件Download Available Firmware,完毕后重启卡件，此过程需要15到20分钟左右的时间；在Hyper-terminal是无法看到任何两个网段端口的信息；10.再次重复第9步完成后会在Hyper-ter

8、minal看到如下信息：-Post 1 sec sleep cnt = 4265 000001 000004265 0 LTMF3 Port Open - 16 C01 / P01 PRIMARY PWS H1 Card 000002 000004265 0 Open Response -ERROR- 16 C01 / P02 PRIMARY PWS H1 Card 000004 000004266 1 Open Response -ERROR- rebootRebooting ARM9 Logic Card此代表其两网段端口未被激活；11.进入Fieldbus Engineering 窗口打

9、开Ovation Developer Studio使用系统树状目录，“System-Networks-Units-Drops-I/O Devices-I/O Devices 0 IOIC-Branch-Slot”导航至“Fieldbus module”在某个现场总线模块上单击鼠标右键，选择“Engineer”，弹出Fieldbus Engineering窗口，选择相应的控制的FF卡件对其Port1和Port2进行Download再次对FF卡件进行修复（79步骤）Download Available Firmware，重启卡件后可以在Hyper-terminal看到以下信息：-Pre 1 sec

10、 sleep cnt = 32247 Divisor = 60Commission data downloading. Port: 1Commission data downloaded sucessfully. Port: 1Pub link downloading. Port: 1Pub link downloaded sucessfully. Port: 1LAS downloading. Port: 1LAS download failed. Port: 1 Error: 88Commission data downloading. Port: 2Commission data dow

11、nloaded sucessfully. Port: 2Pub link downloading. Port: 2Pub link downloaded sucessfully. Port: 2LAS downloading. Port: 2LAS download failed. Port: 2 Error: 88H1Module: 848T3 changed Unknown State - Not Attached-Post 1 sec sleep cnt = 32307 000001 000032307 0 LTMF3 Port Open 1 - 16 C01 / P01 PRIMARY

12、 PWS H1 Card -Post 1 sec sleep cnt = 32307 000002 000032307 1 LTMF3 Port Open 2 - 16 C01 / P02 PRIMARY PWS H1 Card 000003 000032324 0 LTMF3 Open Response Pos 1 - 0 000022 000032327 1 LTMF3 Open Response Pos 2 Not Attached000075 000032397 0 LTMF3 Start Response Pos 20 - 0 H1Module: Port 1: LINK_NOT_D

13、UPLICATE_ADDRESSSendOneMessage1(): XmitReq1() failedSendOneMessage1(): XmitReq1() failed000173 000032437 1 LTMF3 Start Response Pos 38 - 0 H1Module: Port 2: LINK_NOT_DUPLICATE_ADDRESSH1Module: Port 1: LINK_DEVICE_PROBLEMH1Module: Port 2: LINK_GOODSendOneMessage2(): XmitReq2() failed000393 000032569

14、1 LTMF3 SM Identify Response 193 - 20 848T2 0011510848-FR-TEMP-0 x2141C051 H1Module: Port 1: LINK_INITIALIZEDH1Module: Port 1: LINK_GOODCommission data downloading. Port: 1Commission data downloaded sucessfully. Port: 1LAS downloading. Port: 1Pub link downloading. Port: 1Pub link downloaded sucessfully. Port: 1H1Module: Port 2: LINK_INITIALIZEDCommission data downloading. Port: 2Commission data downloaded sucessfully. Port: 2LAS downloading. Port: 2Pub link downloading. Port: 2Pub link downloaded sucessfully. Port: 2000644 000032719 0 LTMF5 Is Taz LAS Event Ind Not AttachedH1Module: 848