pcf2测量报告全尺寸.part1measured

1、CS11_Fully measured ReportProject Name Part Number CAD Number Product Name:CS11: CVT0005308_023: GEAN-PROD-SMBR UPR INR FRT RH LOr:VCC Material standards : VDA 239-CR300LA Actual Material : CR300LAThickness: 1.2mmCoating thickness : GI50/50 -U Detection time :2016/12/13CHECK RESULT 检查结果CHECK DATE检测日

2、期OK.RATIOPart codeP1P2P3TOTAL全尺寸OK Ratio100%100%100%OK Pos139139139Total Pos139139139SURF.型面OK Ratio100%100%100%OK Pos838383Total Pos838383TRIM修边OK Ratio100%100%100%OK Pos444444Total Pos444444HOLE孔位孔径OK Ratio100%100%100%OK Pos121212Total Pos121212RPS InformationY2Y3,Z4Y5Y1X6/Z5Step 1 : Surface Check

3、ingRationalDMIS(TM) External-Array Software, Inc第 1 页RationalDMIS(TM) External-Array Software, Inc第 2 页RationalDMIS(TM) External-Array Software, Inc第 3 页RationalDMIS(TM) External-Array Software, Inc第 4 页Step 2 : Trim CheckingRationalDMIS(TM) External-Array Software, Inc第 5 页RationalDMIS(TM) External

4、-Array Software, Inc第 6 页Step 3 : HolesitionRationalDMIS(TM) External-Array Software, Inc第 7 页RationalDMIS(TM) External-Array Software, Inc第 8 页Step 4 : Hole size CheckingRPS1RPS2安装孔 1安装孔 2安装孔 3安装孔 4nominal12.1(00.15)12.1*16(00.15)(+/-0.5)10.5(00.7)6.5(00.22)10.5(00.7)13*13(00.27)(00.27)actual12.221

5、2.25*16.1210.646.6410.6213.2*13.2deviation000000nominalactualdeviation安装孔 2RPS1安装孔 3RPS2安装孔 1安装4Step 5 : ThinningREPORT CHECKING THINNESMeasure thickness request: 1.2mmactual thickness1.2mmLIMITS MAX : 20%11.1310111298345216721.1431.1341.1451.1561.1371.1681.1691.15101.16111.15121.1713141516THINNING

6、MAX6%Step 6 : Appearance CheckingAppearance Checking 外观检查NO判定标准 Control standard检验方法 Methond判定 OK、NG、N/APicture1零件是否正确？ Is the rignt part?Visual目视OK2变薄率是否 料厚的 20%范 内？ THINNING MAX no more 20%Venire caliper 游标卡尺OK3是否有开裂、暗裂？ No crack,deformationVisual目视OK4毛边、毛刺、尖角是否 0.3mm 范围内？ glitches, indenion,damag

7、ed,Venire caliper 游标卡尺OK5是否有模痕、压伤（无手感可接受）？ No roughness detect with the handwith the handOK6是否有拉伤、划伤？No degradation or deformation手触 with the handOK7是否有起皱、变形（装配面平面度需 0.2MM 以内）？No crack,deformationVisual /Venire caliper目视/游标卡尺OK8是否有生锈？Rust?Visual目视OK9字印是否正确、明显且无手 感？Marking information crrect ?Visual/ with the hand目视/手触OK10公差是否与 3D 公差相符？ Report tolerance is the same with 3D?检查 checkingOK11零件定位是否与检具定义相符？ PRS is the same with gauge?检具 gaugeOK12料边断差是否超过公差带的 50%？ Trim