汽车离合器外文文献翻译、中英文翻译

1、 附录AStick to the car, clutch is an important component of the auto power system, it bears will power and the engine cut and connection between the work. In urban road sections or complex, our most frequently used clutch became one of the components, and clutch, use directly reflects the driving of l

2、evel, but also reflects the good protection for vehicles. Used correctly, principle of clutch clutch in special circumstances using clutch to solve problems, each block is driving the car manual should master enthusiasm.So-called clutch, just as its name implies is using from and close to deliver th

3、e amount of power. By friction clutch, shrapnal, pressure plate and dynamic output shaft, decorate in the engine and transmission between, used to be the flywheel storage engine torque to gearbox, ensure vehicles in different driving conditions apply to drive wheels, belong to the driving force and

4、torque powertrain category. In half the time of the clutch, linkage power input and output power is allowed, namely through rotational speed to realize the amount of power transmission.The clutch is divided into three working condition, not on the clutch type on the part of the clutch, under half st

5、ep down, and the type of clutch type. When the vehicle in normal operation, the pressure plate is tightly packed on the friction of friction, pressure plate and the friction between the biggest slice, input shaft and the output shaft remains relatively static friction between both speed and in the s

6、ame. When the vehicle, the driver started on the clutch pedal, clutch platen movement by pulling back, also is the pressure plate and friction slices, pressure plate and the separation of the flywheel no contact will not exist relatively friction.Finally, also is a type of clutch. At this time, the

7、pressure plate and the friction in small type. Clutch disc friction slices with flywheel is sliding friction between state. The flywheel speed than the output shaft speed, the power transmission from the flywheel part to the gearbox. This engine and driving wheel is equivalent to a soft connection b

8、etween state.Generally speaking, the clutch is started and shift in vehicles, at the time of transmission shaft and a second shaft rotation difference exists between the power of the engine, must be with a shaft cut, can be very good synchronizer will keep a shaft speed and synchronous, block into l

9、ater, again with a shaft through clutch of engine power, power continue to transmit.In the clutch, and an indispensable buffering device, it consists of two similar to the flywheel disc disc playing together, in rectangular groove is decorated in the slots in the spring, the impact of fierce encount

10、er between the two disks, spring, mutual happen elastic cushion external stimuli. Effective protection of engine and clutch. In all parts of the clutch platen, intensity of spring, the friction coefficient, clutch friction, diameter and clutch position number is the key factor decision clutch perfor

11、mance, the stiffness of hydropneumatic spring, the friction coefficient is higher, the diameter of the clutch, clutch performance is better.When beginning to have time, to ensure the linkage of half started smoothly. Sit novice car have such experience, or remove, or started a quiver yishan, these a

12、re not good skills and linkage. The car at the start of the second shaft, gearbox, when we are still hang a block, need on the clutch, a transmission axis and power, through the synchronizer hang a block, a shaft also become motionless. Power is out from the flywheel, there must be a rotating shaft

13、with great speed, which is why started to half of requirements than the shift much when the main reason, clutch before a stationary components, a movement.So the speed of the poor by half linkage to digest must, is at the beginning of the power transmission shaft, and give a part of the vehicle to a

14、 smooth start posture, once the vehicle, speed difference will become small, at this time will clutch, there wont be fully up the impact.Start to higher ramps and linkage skills. Half the speed and the engine can be digested linkage between the wheel speed difference, i.e., the power can be passed t

15、o the wheel, but not running wheel, which often occurred in the ramp. General for driving technology not skilled driver, start up the ramp when handbrake, then let the clutch is linkage, panasonic, vehicle handbrake stationary car after disaster prevention, slip. The gravity of the slide backwards a

16、nd vehicle by the engine is the power to provide against, and clutch is responsible for eliminating the speed difference exists here.Vehicles in this kind of circumstance, the driver can easily start, continue to trample accelerator pedal to obtain enough to further improve speed of torsion, vehicle

17、 goes up the slope. Now the skills required for half a linkage, if half linkage too weak, might efforts in the open hand brake when slide backwards, easy to cause the vehicles panic, if half of a joint efforts, easy is accelerating and hit limber fast-drawing. So for beginners, can let the engine sp

18、eed slightly tall, and the greater half linkage, make vehicles have a walk when the trend, and loosen the handbrake.When will the novice driving some mistakes on the use of the clutch. As a novice, due to driving technology, it will be difficult to unskilled oil from good coordination, resulting in

19、use when the clutch of some beneath the clutch, and these operating methods are also appeared in the half of time.Avoid clutch at half time state can effectively protect the linkage of clutch. Some of the novice just when due to stress, oil from bad cooperation and started out in the car, then remov

20、e and clutch shot big throttle pressure very low, but also dont lift realize all along, the linkage of engine speed and a shaft rotational speed of the huge, and vehicle speed is slowly started, the great speed of all poor by clutch linkage, this is very destroyed digestion. Clutch, In order to avoi

21、d using the ramp frequent trample brake, so half feet in half the speed KongZhiChe linkage to, or a clutch. FrowstyThe whole process of sliding friction clutch occurs, the long time of sliding friction will damage the clutch. Driving on the left foot in general like the clutch not consciously, resul

22、ting in the clutch pedal under pressure for a long time, the vehicles at half linkage. All of these operations can accelerate the clutch disc wear, the dynamic performance and fuel economy of vehicle can cause damage.The clutch is a frequent automobile parts of the friction over time, it will be inc

23、reased frequency of use and wear, and can produce clutch skid phenomenon. For experienced pilots can be found, such as advance whether we can judge the clutch in situ skidding car when a block, then hang soonly, and then slowly lift clutch brake up until completely, if the clutch lift, engine flameo

24、ut this proof of your clutch not sliding, anyway if the clutch is completely lift and car is not leaving the clutch is proof that you.There is in start when suddenly felt clutch position, also the clutch, another is the precursor of sliding speed in urgent when we just feel engine speed in rising, a

25、nd speed, but not all of these conditions are signs of sliding clutch. When the clutch when we want to wear or skid timely inspection, replacement, otherwise will make the engine output power can effectively to the output shaft, but will power loss in the clutch plate and the sliding friction betwee

26、n the flywheel, and the friction between energy consume, for it will cause power transmission, also dues increase the cost of oil transport.附录B对于手动挡的车型而言，离合器是汽车动力系统的重要部件，它担负着将动力与发动机之间进行切断与连接的工作。在城市道路或者复杂路段驾驶时，离合器成了我们最频繁使用的部件之一，而离合器运用的好坏，直接体现了驾驶水平的高低，也体现了对于车辆保护的好坏。正确使用离合器，掌握离合器的原理以在特殊情况下利用离合器来解决问题，是每

27、个驾驶手动挡车型的车友应该掌握的。所谓离合器，顾名思义就是说利用“离”与“合”来传递适量的动力。离合器由摩擦片，弹簧片，压盘以及动力输出轴组成，布置在发动机与变速箱之间，用来将发动机飞轮上储存的力矩传递给变速箱，保证车辆在不同的行驶状况下传递给驱动轮适量的驱动力和扭矩，属于动力总成的范畴。在半联动的时候，离合器的动力输入端与动力输出端允许有转速差，也就是通过其转速差来实现传递适量的动力。离合器分为三个工作状态，即不踩下离合器的全连动，部分踩下离合器的半连动，以及踩下离合器的不连动。当车辆在正常行驶时，压盘是紧紧挤靠在飞轮的摩擦片上的，此时压盘与摩擦片之间的摩擦力最大，输入轴和输出轴之间保持相对

28、静摩擦，二者转速相同。当车辆起步时，司机踩下离合器，离合器踏板的运动拉动压盘向后靠，也就是压盘与摩擦片分离，此时压盘与飞轮完全不接触，也就不存在相对摩擦。最后一种，也就是离合器的半连动状态。此时，压盘与摩擦片的摩擦力小于全连动状态。离合器压盘与飞轮上的摩擦片之间是滑动摩擦状态。飞轮的转速大于输出轴的转速，从飞轮传输出来的动力部分传递给变速箱。此时发动机与驱动轮之间相当于一种软连接状态。一般来说，离合器是在车辆起步和换挡的时候发挥作用，此时变速箱的一轴和二轴之间存在转速差，必须将发动机的动力与一轴切开以后，同步器才能很好的将一轴的转速保持与二轴同步，挡位挂进以后，再通过离合器将一轴与发动机动力结

29、合，使动力继续得以传输。在离合器中，还有一个不可或缺的缓冲装置，它由两个类似于飞轮的圆盘对在一起，在圆盘上打有矩形凹槽，在凹槽内布置弹簧，在遇到激烈的冲击时，两个圆盘之间的弹簧相互发生弹性作用，缓冲外界刺激。有效的保护了发动机和离合器。在离合器的各个配件中，压盘弹簧的强度，摩擦片的摩擦系数，离合器直径，摩擦片位置以及离合器数目就是决定离合器性能的关键因素，弹簧的刚度越大，摩擦片的摩擦系数越高，离合器的直径越大，离合器性能也就越好。起步时需要有一定的半联动时间，以保证起步的平顺。坐新手开的车都有这样的体会，要么起步时熄火，要么是一颤一颤出去的，这些都是半联动技巧没有掌握好的表现。汽车在起步的时候

30、，变速箱的二轴是静止的，当我们挂一挡以前，需要踩下离合器，此时变速箱的一轴与动力分开，通过同步器挂上一挡以后，一轴也同样变为静止。动力从飞轮出来是有一定转速的，此时与一轴存在巨大的转速差，这也就是为何起步时对于半联动的要求要比换挡时高得多的主要原因，离合器的前后部件一个静止一个运动。这样的转速差必须由半联动来消化，也就是动力开始的时候部分传递给一轴，使车辆能以较平稳的姿态起步，一旦车辆行驶起来，转速差就会变得很小，此时将离合器完全抬起，就不会有冲击了。坡道起步需要较高的半联动技巧。半联动可以消化发动机转速与车轮之间的转速差，也就是说可以有在动力已经传递到车轮上，但车轮并不运转的情况出现，这种情况常常发生在坡道。一般对于驾驶技术不熟练的驾驶员而言，在坡道起步时会拉起手刹，然后让离合器处于半联动状态，松下手刹，车辆保持静止，防溜车殃及后车。而车辆向后滑行的重力是由发动机提供的动力来