模具专业术语英文

1、精选优质文档-倾情为你奉上注塑、模具专业英语Surface Appearance外观Glossiness/gloss finish光洁度、粗糙度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface玻纤外露、浮纤Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹、料花Flow mark流纹Brittle/brittleness脆、脆性Bubble

2、s/trapped gas气泡/困气Void孔、气泡Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃等级V-2Poor dispersion分散不好FR/PTFE agglomerates etc阻燃剂/PTFE结块Pellet porous颗粒料孔隙、Low impact/tensile strength etc低冲击强度/拉伸强度等High flow/filler content etc高流动性/过度填充Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles纤

3、维结团Product was rejected due to 产品不能接受因为High moisture level高水分、高湿度Warpage/warped翘曲/变形Shrinkage/shrink收缩/收缩率Sink marks凹陷、缩水Short shot/short molding打不满、欠注Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边、披锋、溢边Discoloration变色Off color颜色差异Flow rate流动速率Viscous/viscosity粘性的、粘的/黏度High flow高流动Low f

4、low低流动Sticky粘的，粘性的Sticking core粘后模，粘模芯Sticking sprue粘水口Sticking cavity粘前模Mold release（agent）脱模(剂)Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted p

5、roduct specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra 添加多一点Reduced content减少含量Dropped/reduced by x减少含量Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is unde

6、r testing产品在测试当中Received first order接了第一个定单Expected to finish by 预计在完成Expected order is xMT预计定单量吨Estimated annual/monthly consumption预计年/月用量 模具方面：Ejection system顶出系统、脱模系统pin顶针、推杆spring弹簧Gate type浇口类型Sprue主流道runner分流道cavity模腔Sprue gate直浇口Pin point gate点浇口Tab gate护耳浇口Fan gate 扇形浇口Tunnel or submarine g

7、ate潜伏式浇口Jump gate跳跃式浇口Diaphragm gate片状浇口Ring gate 环形浇口The cavity of the mould模腔Heated cylinder加热料筒Surface finish表面光洁度Sink mark缩水Air trap困气Gas trapped气体困着，困气void空隙，孔galling烧焦Weld line熔接痕，熔合线Drag mark划伤、脱模痕Scratch mark模具刮花Deformed/ warp变形Ejector not returned顶针不回位slide滑块、行位streak波纹、条纹、色痕delamination分层J

8、etting mark喷射痕Gate mark浇口痕rib筋、加强筋、骨位boss凸台、凸起、凸痕Melt flow length熔体流线长度Ejector plate顶针板Stop pin限位销Push rod推杆、顶针Push back pin复位杆Ejector guide pin顶针导柱Cold-slug-well冷料井、冷料穴plate模板Ejected mark顶痕，顶白nozzle喷嘴Surface defect表面缺陷Air vent排气口Filling uneven走胶不平衡、进胶不平衡pressure:压力speed:速度control:控制protection pressure:保压mold:模set:设定option:选择injection:射胶pressure reducing valve :减压阀relief valve:泄压阀max:最大  max:最大system:系统    pr