eva-hp 存储安装

1、This document describes the procedures necessary to complete the installation and configuration of the Enterprise Virtual Array. When these procedures are complete, you can begin using your storage system. NOTE: Installation of the Enterprise Virtual Array should be done only by an HP authorized ser

2、vice representative. The information in this chapter provides an overview of the steps involved in the installation and configuration of the storage system. This chapter consists of: · Storage system connections · Procedures for getting started · Gathering information · Entering

3、data using the Operator Control Panel (OCP) · Installing HP Command View EVA · Installing optional EVA software licenses Storage system connections The following links will take you to documents that provide information on EVA storage system connections. · EVA8000 storage system conne

4、ctions · EVA6000 storage system connections · EVA4000 storage system connections Procedures for getting started Step Responsibility 1. Gather information and identify all related storage documentation. Customer 2. Contact an authorized service representative for hardware configuration info

5、rmation. HP Service Engineer 3. Enter the World Wide Name (WWN) into the OCP. HP Service Engineer 4. Configure HP Command View EVA. HP Service Engineer 5. Prepare the hosts. Customer 6. Configure the system through HP Command View EVA. HP Service Engineer 7. Make virtual disks available to their hos

6、ts. Refer to the storage system software documentation for each hosts operating system. HP Service Engineer Gathering information The following items should be available when installing and configuring an Enterprise Virtual Array. They provide information necessary to set up the storage system succe

7、ssfully. · HP StorageWorks 4000/6000/8000 Enterprise Virtual Array World Wide Name label , which is shipped with the system. · HP StorageWorks 4000/6000/8000 Enterprise Virtual Array read me first. · HP StorageWorks 4000/6000/8000 Enterprise Virtual Array release notes. · The lat

8、est HP OpenView Storage Management Server Update, which consists of the management server update CD and its associated documentation, or the latest Windows Server Update o You can determine the latest update version available by checking the release notes or contacting your authorized service repres

9、entative to find out how to receive the latest information. o Additional documentation is available from the following HP web sites: § § § Locate these items and keep them handy. You will need them for the procedures in this document. Host information Make a list of information for ea

10、ch host computer that will be accessing the storage system. You will need the following information for each host: o The LAN name of the host o A list of World Wide Names of the FC adapters, also called host bus adapters, through which the host will connect to the fabric or fabrics that provide acce

11、ss to the storage system o Operating system type o Available LUN numbers Entering data using the Operator Control Panel (OCP) NOTE: This procedure should be performed by an HP authorized service representative. Two pieces of data critical to initial setup must be entered into the OCP: · WWNMand

12、atory to complete setup. This procedure should be performed by an HP authorized service representative. · Storage system passwordOptional. A password is a security interlock that allows only specific instances of HP Command View EVA to access the storage system. Setting up a controller pair usi

13、ng the OCP Fibre Channel protocol requires that each controller pair has a unique Node WWN. This 16-character alphanumeric name identifies the controller pair on the storage system. The Enterprise Virtual Array World Wide Name label identifies the WWN for each storage system. The Node WWN labels ide

14、ntify the storage system WWN and checksum (see Figure 1). During the installation of the storage system, two WWN labels are attached to the rack on both sides of the controller enclosures. Figure 1: Sample node WWN label NOTE: The controller pair WWN is unique to a controller pair and cannot be used

15、 for any other controller pair or device anywhere on the network. Figure 2 shows the location of the WWN label, one either side of a controller pair. This is the only WWN applicable to any controller installed in a specific physical location, even a replacement controller. Once a WWN is assigned to

16、a controller, you cannot change the WWN while the controller is part of the same storage system. Figure 2: Location of the World Wide Name label 1 - World Wide Name label Entering the WWN Table "WWN push button functions" lists the push button functions when entering the WWN or the WWN che

17、cksum. NOTE: The following sections describe procedures that require use of the OCP. For more information about the OCP, see HP StorageWorks EVA 4000, 6000, 8000 - HSV controllers, Identifying and Using. WWN push button functions Button Function Selects a WWN or checksum character by scrolling up th

18、rough the character list one character at a time. If you select an incorrect character, you can use either or to select the correct character. Moves forward one character. If you accept an incorrect character, you can move through all 16 characters, one character at a time, until you display the inc

19、orrect character. You can then change the character. Selects a WWN or checksum character by scrolling down through the character list one character at a time. If you select an incorrect character, you can use either or to the select correct character. Moves backward one character. Complete the follo

20、wing procedure to assign the WWN to each pair of controllers. Either controller can be used to input the WWN. 1. Turn the power switches on both controllers off. 2. Apply power to the rack. 3. Turn the power switch on both controllers on. NOTE: Notifications of the startup test steps that have been

21、executed are displayed while the controller is booting. It may take up to two minutes for the steps to display. 4. The WWN entry display has a 0 in each of the 16 positions. 5. Press or until the first character is displayed. Press to accept this character and select the next. 6. Repeat Step 5 to en

22、ter the remaining characters. 7. Press Enter to accept the WWN and select the checksum entry mode. NOTE: For the location of the WWN Checksum, see Figure 2. Entering the WWN checksum The second part of the WWN entry procedure is to enter the two-character checksum, HS, as follows. 1. Verify that the

23、 initial WWN checksum displays 0 in both positions. 2. Press or until the first checksum character is displayed. Press to accept this character and select the second character. 3. Press or until the second character is displayed. Press Enter to accept the checksum and exit. 4. Verify that the defaul

24、t display is automatically selected. This indicates that the checksum is valid. NOTE: If you enter an incorrect WWN or checksum, the system will reject the data and you must repeat the procedure. Setting the storage system password The eight-character storage system password feature enables you to r

25、estrict certain functions to selected resource managers. Table "System password push button functions" describes the push button functions when using the password feature. System password push button functions Button Function Selects a password character by scrolling up through the charact

26、er list one character at a time (AZ and 09). Accepts the current character and selects the next character. If you accept an incorrect character, you can loop through the display, one position at time, to select the character to be changed. Selects a password character by scrolling down through the character list one character at a time. ESC Returns to the default display. ENTER Accepts all the pass