YZP系列样本要点

1、YZP系列变频调速三相异步电动机YZP series freque ncy speed con trol three-phase asynchronous motor1、概述YZP系列冶金及起重用变频调速三相异步电动机，用于驱动各种型式的起重机械及其他类似设备的专用产品；是以变频调速装置为供电电源的专用电动机。能与国内外各种变频装置配套，组成变频调速系统。电动机调 速范围广、过载能力强、运行稳定、可靠、效率高。因此，它特别适用于那些短时或断续运行，频繁地起动、制动、 有时过负荷及显著振动与冲击的设备。2、使用条件海拔不超过1000m能正常运行。F级适用于环境空气温度在 -20C至U 40C之间

2、，H级适用于环境空气温度在 -20C 到60C之间。相对湿度小于 90%。3、基本型式标称电压：380V基 频：50Hz, 1-50HZ恒转矩调速，50-100HZ恒功率调速防护等级：IP54绝缘等级：F级或H级冷却方式：风机冷却(IC416)基准工作制：S3-40%安装方式：B3 ( 112400)、B5 (112250)、V1 (112315)、B35 (132315)定子接线方式：160及以下电机定子绕组为 Y接法；180及以上电机定子绕组为接法注：根据用户要求，可带超温保护开关、防潮加热带、电磁制动器、编码器及超速开关等，可根据用户要求提 供基频50Hz以下的电机。4、冷却风机型式标称

3、电压：380V基 频：50Hz基准工作制：S1对应机座号的轴流风机功率见表1表1对应机座号的轴流风机功率(Table1Number of frame and fan power)机座号Number of frame112132160180200225250280315355400450轴流风机功率Drive motor of fan9040808015020023023035060011001100Output power (W)注：根据用户要求，可采用用离心风机的冷却对应机座号的离心风机功率见表 2表 2 对应机座号的离心风机功率(Table2 Number of frame andcent

4、rifugal fan power)机座号Number of frame132160180200225250280315355400450风机型号type of cen trifugal fanL-04L-05L-06L-064L-08L-11风机电机功率power of centrifugal fan motor60W180W370W1.1 kW35.5kW风机电机极数pole of centrifugal fan motor222224风机必须由独立电源供电1. Gen eralYZP series WVF adjustable speed motors for metallurgy an

5、d crane are specially used for driv ing various cranes and other similarity equipme nt. The YZP series use freque ncy conversion adjustable speed power and can be used with various variable frequency units at home and abroad. The YZP series have wide adjustable speed range, high overload capacity, h

6、igh reliable, high efficiency. The YZP series are very suitable the machine which frequency start and stop or interrupted duty with start ing, brak ing, in verse freque ntly.2. Operati on con diti onThe motor can run no rmally whe n the elevati on not more tha n 1000m. The environment temperature fo

7、rclass F isfrom -20 to 40 Celsius degree , for H class from -20 to 60 Celsius degree. Relative humidity less 90%.3. Base moderated voltage: 380V.base frequency: 50Hz , 1-50Hz constant torque adjustable speed, 50-100Hz constant power adjustable speedprotect ion Class:IP54in sulati on class: F or Hcoo

8、ling mode: fan cooling (IC416 )base operat ing duty : S3-40%in stall mode: B3 (112450 )、B5 (112250 )、V1 (112315)、B35 (132315)wi nding connection: Y to 160 and below; to 180 and aboveAccord ing to the agreeme nt, the follow ing are opti on al: over-temperature protect ion, dampproof heati ng belt, br

9、ake, rotary en coder, over-speed switch.4. Cooli ng fanRated voltage: 380V.Base freque ncy: 50Hz ,Base operat ing mode : S1Accord ing to the dema nd of customer, we can provide cen trifugal fan.The power of drive motor show n in table1 and table 2.Fan must be powered in depe nden tly!5. yzp系列变频调速电动机

10、型号意义:Significance of models of YZP series frequency (speed) motor极数Number of poles机座长短代号 Long and short code of frame中心高(mmHeight of center (mm)160 L - 4异步电机Asynchronous motor 冶金及起重用For metallurgy and lifting 变频调速Frequency conversion and speed adjustment注：电机带带风机、制动器或编码器，则其型号加上其对应的符号。Note: In case th

11、at the motor is equipped with fan moter 、 brake or rotary encoder, the corresponding characteristic6.变频电机基准工作制为S3-40%, 280及以下中心高其它工作制功率换算关系见表3, 315及以上中心高其它工作制功率换算需与厂家联系表3工作制功率换算关系 (Table 3 duty and power)工作制dutyS1S2S3S4100%30 minutes60 minutes15%25%40%60%150 times/hour300 times/hour功率折算关系Conversion1

12、.001.101.001.351.101.000.800.830.73relation of powerr6. The base duty of the freque ncy conversion motor is: S3-40%, the conversion relati on with other characters of service is as table 3:7. YZP系列电机主要技术参数：Main technical parameters of YZP series motor (only for reference, see the nameplate of the mo

13、tor for details): 电机为 4 极 表(1) motor with four poles (table 1)型号model标称 功率nominal power (kw)额定 电流 rated current(A)额定转矩rated torque (N.m)额定转速rated speed(r/min)堵转转矩额定转矩 ratedtorqud locked rotor torque(1HZ最大转矩额定转矩 rated torque / ma;torque(50Hz)转动惯量x. moment of inertia kg m重量weight(kg)YZP100L 2-42.26151

14、3901.522.90.016535YZP112M 1-42.261513901.523.00.017050YZP112M 2-438.020.514001.523.00.017353YZP112M 3-44.09.52714151.523.00.017555YZP132S-45.512.23614501.523.10.04878YZP132M-47.516.94814501.523.20.05692YZP160M 1-47.516.94814501.523.20.09105YZP160M 2-411237114651.523.40.11115YZP160L-415309814651.523.

15、50.125130YZP180M-418.53712014651.523.50.30195YZP180L-4224714614501.523.30.35210YZP200L 1-4305719514701.523.50.263280YZP200L 2-4377024014701.523.20.273300YZP225S-4377024114651.523.20.273360YZP225M-4458729314651.523.30.469400YZP250M-45510235614751.523.00.66480YZP280S1-46311740814751.523.01.08555YZP280

16、S2-47513648614751.523.01.12572YZP280M-49016558314751.523.01.15677YZP315S1-411020071514701.523.13.11990YZP315S2-413223185814701.523.13.111023YZP315M 1-4160281104014701.523.03.621092YZP315M 2-4200352129914701.523.04.131161YZP315L-4220387142814711.523.24.941720YZP355Ma4220386142014801.523.15.751454YZP3

17、55M-4250440159314801.523.15.751870YZP355L-4315550200814801.523.16.791870电机为 6 极 表( 2) motor with six poles (table 2)型号model标称 功率 nominalpower (kw)额定 电流 rated current(A)额定 转矩 rated torque (N.m)额定转速rated speed(r/min)堵转转矩额定 转矩rated torque / locked rotor tore(1HZ最大转矩额 定转矩rated torque uemax. torque (50Hz

18、)转动惯量/ moment of inertia kg m重量weight (kg)YZP112M-62.26.022.59301.523.00.02055YZP132S-637.5309601.523.10.05258YZP132M 1-649.8409601.523.10.056292YZP132M 2-65.512.7559601.523.10.057597YZP160M-67.518749701.523.00.1325132YZP160L-611261089701.523.10.1775152YZP180M-611221089701.523.10.1775220YZP180L-6153

19、01489701.523.20.31220YZP200L 1 -618.5371829701.523.20.312230YZP200L 2-622452149801.523.30.315250YZP200L 3-630602909801.523.00.361290YZP225M 1-630602909801.523.00.4300YZP225M 2-637733609821.523.00.547318YZP250M 1-637713599851.522.90.834415YZP250M 2-645854389821.522.90.834430YZP280S1-645854389821.522.

20、90.9450YZP280S2-6551025339851.523.01.39550YZP280S3-6631306119851.523.01.5580YZP280M-6751437279851.523.11.65620YZP315S1-6751367279851.523.14.01915YZP315S2-6901708629851.523.14.11915YZP315M 1-611020610669851.523.24.781025YZP315M 2-613224612799851.523.05.451098YZP315L-616029715519851.523.06.121165YZP35

21、5M 1-620036919499801.523.58.021690YZP355M 2-622040321449801.523.59.361730YZP355L-625045024369801.523.510.541820YZP400L 1 -631555130709801.523.512.52400YZP400L 2-633058532159801.523.513.92500YZP400L 3-635562534289891.523.515.62800YZP450L 1 -640071038399951.523.637.83400YZP450L 2-645081043199951.523.6

22、443800YZP450L 3-650092047989951.523.6454000电机为 8 极 表(3)motor with eight poles (table 3)型号model标称 功率nominal power(kw)额定 电流 rated current(A)额定转 矩rated torque (N.m)额定转 速rated speed (r/min)堵转转矩/额定 转矩rated torqu / lockec rotor torqu(1HZ最大转矩 额定转矩rated e torque / max.e torque(50Hz)转动惯 量moment of inertia2kg

23、 m重量weight (kg)YZP132S-82.26.4297251.522.60.052580YZP132M-838.539.57251.522.60.056292YZP160M 1-8410.852.37301.522. 80.0575110YZP160M 2-85.514.5727301.522.80.1325125YZP160L-87.519987301.522.80.1775152YZP180L-811261447301.522.80.325220YZP200L-815311987251.522.80.339260YZP225Si-818.5382447251.522.80.41

24、265YZP225S2-822482867351.522.90.491270YZP225M-830683907351.522.90.547292YZP250M 1-830593927301.522.90.75458YZP250M 2-837764817351.522.80.834462YZP280S1-837754837321.522.81.15500YZP280S2-845935857351.523.01.39520YZP280M-8551217147351.522.91.65592YZP315S1-8551087117391.523.14.5940YZP315S2-863122814739

25、1.523.14.6950YZP315S3-8751549747351.523.14.791000YZP315M 1-89018211697351.523.15.581100YZP315M 2-811021014297351.523.06.371160YZP315L-813225017157351.522.97.321230YZP355M 1-816032020797351.522.99.41690YZP355M 2-820039325997351.522.911.381790YZP355L-822042528597351.522.913.81990YZP400L 1-825043532487

26、351.523.122.92500YZP400L 2-826045633517411.523.122.92500YZP400L 3-828050336237381.523.126.82600YZP450L 1-831556040497431.523.1443300YZP450L 2-835565045457461.523.646.53400YZP450L 3-840075051217461.523.654.33800YZP450L 4-845083057607461.523.6554000电机为 10 极表(4)motor with ten poles (table4)型号model标称 功率

27、 nominalpower (kw)额定 电流 rated curre nt(A)额定转 矩rated torque (N.m)额定转 速rated speed (r/min)堵转转矩/额定转矩rated torque / lockrotor torque(1HZ最大转矩额 定转矩edrated torque max. torque (50Hz)转动惯量moment/of inertiakg m重量weight(kg)YZP280S-1037816045851.523.01.39520YZP280M-10451007355851.523.01.65590YZP315S1-10551198985

28、851.523.34.79970YZP315S2-106313410285851.523.35.581070YZP315M 1-107515612245851.523.26.371130YZP315M 2-109018014695851.523.07.151210YZP315L-1011022017965851.522.77.251230YZP355M 1-1013227721555851.522.710.91680YZP355M 2-1016033326125851.522.713.71730YZP355L-1020041832655851.522.715.81990YZP400L 1-10

29、20039632375901.522.926.82400YZP400L2-1022042735495921.522.926.82400YZP400L3-1025048540335921.522.926.82500最大转矩额定转矩为OHM的值,堵转转矩额定转矩为Hz时的值，与变频器设置有关。The values ofrated torque / locked rotor torque and rated torque / max. torque are related with freque ncy conv erter.8.安装外形尺寸YZP 112-450（电机轴流风机冷却）B3安装见表5、

30、YZP 112-450（电机离心风机冷却）B3安装见表6YZP 112-280（电机轴流风机冷却）B5安装见表7YZP 132-315（电机轴流风机冷却）B35安装见表8YZP 112-450（电机离心风机冷却）B3(双轴伸）安装见表9可根据用户要求提供 YZP112-160自散热电机，其安装尺寸同风机冷却电机8. Outline dimension of installationYZP112-450 (motor cooled with fan) B3see table 5 for in stallatio nYZP112-450 (motor cooled with fan) B3see

31、table 6 for in stallatio nYZP112-280 (motor cooled with fan) B5see table 7 for installationYZP132-315 (motor cooled with fan) B35see table 8 for installationYZP112-450 (motor cooled with fan) B3(double end shaft)see table 9 for installationThis works can produce YZP112-160 non-ventilated motor (with

32、out fan) according to the requirements of the customers. The installation dimensions are same to the motor with fan.9.定货须知9.1 定货时写明型号、额定功率、额定电压、额定频率、安装方式，防护等级等。9.2 特殊要求请在合同中写明。本厂接受特殊定货。9. Ordering information9.1 The model, rated power, rated voltage, rated frequency, installation mode, protection gr

33、ade and so on of the motor shall be written down in ordering.9.2 In case of special requirement on motor, please contact this works fornegotiation and acceptance of the specialordering.A-A|fcMAC表5 B3 机座有底脚，端盖无凸缘的电机 （轴流风机冷却）单位：mmTable 5: motor with fan the stator frame with the footing and the end co

34、ver without the flangeUnit: mm机座号Frame安装尺寸 Installation dimensions夕卜形尺寸 Outline DimensionsHABCDEFX GDGKABBBACHDHAW1W2L1L2112M1121901407028608 X 72412245225235330202550520600132S13221614089388010X 83312270280270365222050620720132M13221617889388010X 83312270280270365222050620720160M1602542101084211012

35、X 83715315270314400262760740845160L1602542541084211012X 83715315310314400262760780885180M1802792411214811014X 942.515355370360458254172830940180L1802792791214811014X 942.515355370360458254172850970200L2003183051335511016X 1049194053804055052524908901030225S2253562861496014018X 1153194504154305452832

36、.5909701125225M2253563111496014018X 1153194504154305452832.5909701125250M2504063491686514018X 1158245015054805953050.5951050-280S2804573681907514020 X 1267.52457052753566032601001100-280M2804574191907514020 X 1267.52457057853566032601001150-315S3155084062168017022 X 14712863566062087035551301310-315

37、M3155084572168017022 X 14712863566062087035551301310-315L3155085082168017022 X 14712863566062087035551301360-355M3556105602549517025 X 14862873583770095038861401600-355L3556106302549517025 X 14862873583770095038861401600-400L40068671028013025028 X 1612028850880850110050751601800-450L4508001000250130

38、21032X18119399901300990125052134.51902070注：L*分别为L1和L2,L1为电机不带制动器、编码器的尺寸，L2为电机带制动器、不带编码器的尺寸。若另带编码器，则长度尺寸要加上编码器长度。Note：L* in eludes L1 and L2. L1 is the size of motor without brake and rotary en coder; L2 is the size of motor with brake and without rotary en coder.If rotary encoder is added, the size

39、of rotary encoder shall be added to the whole size.。AC表6 B3 机座有底脚，端盖无凸缘的电机 （离心风机冷却）单位：mmTable6: motor with centrifuga I fan the stator frame with the footing and the end cover without the flange Unit: mm机座号Frame安装尺寸 In stallati on dime nsions夕卜形尺寸 Outli ne Dime nsionsHABCDEFX GDGKABBBACHDHAW1W2L1L21

40、12M1121901407028608 X 72412245225235460202550460540132S13221614089388010X 83312270280285540222050620720132M13221617889388010X 83312270280285540222050620740160M1602542101084211012X 83715315270314575262760740845160L1602542541084211012X 83715315310314575262760780885180M1802792411214811014X 942.51535537

41、0360660254172830940180L1802792791214811014X 942.515355370360660254172850970200L2003183051335511016X 1049194053804057102524908901030225S2253562861496014018X 1153194504154307602832.5909701125225M2253563111496014018X 1153194504154307602832.5909701125250M2504063491686514018X 1158245015054808853050.59510

42、50-280S2804573681907514020 X 1267.52457052753594532601001100-280M2804574191907514020 X 1267.52457057853594532601001150-315S3155084062168017022 X 147128635660620101035551301310-315M3155084572168017022 X 147128635660620101035551301310-315L3155085082168017022 X 147128635660620101035551301360-355M355610

43、5602549517025 X 148628735837700123038861401600-355L3556106302549517025 X 148628735837700123038861401600-400L40068671028013025028 X 1612028850880850135050751601800-450L450800100025013021032X18119399901300990154052134.51902070注：L*分别为L1和L2,L1为电机不带制动器、编码器的尺寸，L2为电机带制动器、不带编码器的尺寸。若另带编码器，则长度尺寸要加上编码器长度。Note：

44、L* in eludes L1 and L2. L1 is the size of motor without brake and rotary en coder; L2 is the size of motor with brake and without rotary en coder.If rotary encoder is added, the size of rotary encoder shall be added to the whole size.。机座号Frame安装尺寸Mountingdimensions外形尺寸Outline dimensionsDEFXGDGTMNPRSADHDLAL1L2112M2860r 8 x 7244215180 125004 x 1519030014520