理光afico200sp资料（理光graph200sp资料）

1、理光afico 200 sp资料(理光graph 200 sp资料)program number function settings filefirst and second paragraph, third paragraph1-1011, no counterpoint (regular copy), 9/-92, no counterpoint (double copy), 12.5/-12.51-002 1 horizontal alignment (first paper road) 9/-92 horizontal alignment (second paper road) ibi

2、d3 horizontal alignment (third paper road) ibid4, fourth paper road ibid5 hands paper, ditto6, double side, ditto1-003 1 supply timing (paper tray) 0/102 feeding timing (hand feed) 0/101-005 1 fixing temperature adjustment 100/2002 fixing temperature adjustment (level 2) 0/165 1-106 fixing temperatu

3、re display1-902 fixing control frequency display 2001 charging roller bias adjustment -1000/25002-1011 frontdeletion blank (print) 0/92 end delete blank,print the same as above3,4 right sidedelete blank print,dittoleft side blank print, ditto2-106 test graphics id, adjust 0/2552-201 development bias

4、 adjustment "-200/-900 2-213, detect the toner after the use of the number of copies can be 0:50, 1:20 2-220 vt display2-801 toner concentration sensor initial setting 0: no; 1: yes2-907 laser pulse location 0: center; 1: base： 2: right; 3: add up2-908 mandatory powder 0: no; 1: yes2-909 chargi

5、ng roller compulsory cleaning, ditto 2-910 transfer roller compulsory cleaning, ditto2-911 image concentration choice 0: thicker; 1: thick; 2:normal; 3: shallow; 4: shallower2-913 t sensor automatic initialization 0: no; 1: yes2-995 it sensor control voltage: factory set point display2 the display o

6、f the total counter at the factory setting2-996 it sensor control value setting 80/1702 the value of the total counter when settingdisplay of 2-997 it sensor control value (when installing)2 the value of the total counter when setting2-999, t sensor control voltage selection 0: factory settings;1: m

7、anual settings; 2: the implementation of the initial set4- 008 adjustment of main scan rate t/+14010 sub scan alignment adjustment -2/94- 011 master scan alignment adjustment "-6/+64012 1 scan, the margin is adjusted 0/92 ends blank3 left blank, ditto4 right, left blank, ditto4- 013 scan stand

8、free running 0: no: 1: yes4-101 scan rate adjustment "-1/+1"4- 902 exposure lamp force 0: no; 1: yes5- 001 operate all lights5- 104 a3 count doubled 0: no; 1: yes5- 106 automatic concentration level setting l/7the 5-501 1pm call cycle is set 0/2552pm warning 0: no; 1: yes3pm warning (copy)

9、5-801 total clear5-802 free running 0: no; 1: yes5-803 input check5-804 output check 5-810 sc code reset 0: no; 1: yes6- 006 1 manuscript master scan alignment adjustment -1. 5/1. 5the 2 sean alignment adjusts -10/+103 trailing margin adjustment "一3.0/+306- 007 send manuscript sub scanning rate

10、 adjustment "-4/+46- 009 feeder free running 0: no: 1: yes7- 803 pm counter display7- 804 pm counter resetinput check mode:1 front door safety switch +24v 37 double side entrance sensor2 front door safety switch - ld5v 38 flip into assembly3 right side vertical guide switch 39, double face moun

11、ting4 left side vertical door sensor 48 for paper cover sensor5 left door sensor 49 original insert sensor6 fixing part, output paper sensor 50, manuscript feeder position sensor7 position sensor 51 on the paper sensor8, the next paper sensor, 60 xin surface mirror motor stuck9 alignment sensor10 to

12、p relay sensor completesensor11 the charging roller is connected with the12 hand feed paper, disposable paper sensor13 run the paper out of the sensor14 run out of paper, paper, sensor15 paper size sensor16 paper size sensor17 the main motor is jammed23 run out of paper sensor24 run out of paper sen

13、sor25 upper trunk sensor26 relay sensor27 paper size sensor28 paper size sensor29 paper cabinet lid switch30 paper cabinet31 the main motor is jammed32 upper tray sensor33 paper upper limit sensoroutput check: 1 shunt valve, electromagnet 29, double side section valve, electromagnet2 contraposition

14、electromagnet 38df supply paper motor3 upper relay clutch 39df supply paper motor (slow down)4 relay clutch 40df paper rolling electromagnet (optional adf)the 5 pick from the charging roller clutch 41 printer lift iron (optional adf)6 manual paper feeding paper for clutch clutch 42df7 for paper clut

15、ch 53 polygon mirror motor8 feeding clutch9 developing part of clutch10 toner bottle drive motor11 main motor (forward)12 main motor (reverse)13 rows of wind motor19 for paper clutch20 feeding clutch21 clutch relay22 clutch relay23 main motorthe 24 paper on the rise and fall of motorthe 25 paper lif

16、ting motorthe 26 paper on the rise and fall of motorthe rise and fall of 27 paper machine28 do not usesc code instructions:in situ sc120 seanning frame error 1in situ scanning frame sensor can not in the initial setting or copying process detected in the off statethe possible reason:in situ scanning

17、 frame sensor failurescanner drive motor failureioscc board failurethe wire harness seanning frame in situ sensor is badin situ sc121 scanning frame error 2at the beginning of the setting in the process of copying or scanning frame in situ sensor can not detect the conduction statethe possible reaso

18、nin situ scanning frame sensor failurescanner drive motor primary effectioscc board failurethe wire harness scanning frame in situ sensor is badin situ sc121 seanning frame error 3seanning frame back in situ scanning frame in situ sensor detects the conduction statethe possible reasonin situ scannin

19、g frame sensor failurescanner drive motor failureioscc board failurethe wire harness seanning frame in situ sensor is badin situ sc123 scanning frame error 4scanning frame back to the in situ scanning frame in situ sensor does not detect the conduction statemay causein situ scanning frame sensor fai

20、lurescanning frame potato motor failureiocss board failurethe wire harness scanning frame in situ sensor is badsc192 sby error adjustmentsbu automatic adjustment due to error detection processsbu badbicu badlamp failureexposure lamp failuredirty boardsc302 charging and leakagedue to current leakage

21、signal detection and chargingcharge roller failurecharging power supply sideadverse drug pcu connectionsc306 charging and in situ errorthe charging roller connected from the sensor sidepick from the charging roller clutchsc320 polygon mirror motor abnormalitythe connected signal mirrors of motor iss

22、ued after 10 seconds, the motor does not reach the speed of action, or even in the action processthe polygon mirror motor sidethe contact between the red moving plate and the iocss panel is not good enough to connect the multi mirror motoriocss board failuresc321 does not have a laser output signalc

23、pu can not detect the laser output signal when the copy paper reaches the position sensorbicu board is badmsu board is baderrors in synchronization of sc322 laserswith more than 5 consecutive 100ms intervals indeed, the main scan synchronization detector board does not detect the sync signal of the

24、laserconnect the laser synchronization panel to the bicu panel, and the wiring harness is out of contactthe laser synchronization detector board is not in place properlylaser synchronization detector board failurebicu board is badthe sc324 ld driver board adds current over ld to the 100mald device i

25、s badthe wiring harness connecting the ld device to the bicu board is not connected properlythe temperature is too high around the ld devicesc390 td sensor error 1after the initial setting of the td sensor, the 20std sensor outputs less than 0. 5vsc391 development output abnormalthe pw outputs 200ms continuously at 62% of the loadsc393 td sensor error 2after the initial stage of the td, the output voltage of the td exceeds the adjustment rangesc401 transfer positive output abnormalsc402 transfer negative output abnormalsc411 separates output anomaliessc503 the paper traysc504 the paper tra