巴可DP2K系列故障代码

1、barco dp2k系列故障代码译表本文将列举绝大部分会显示在巴可dp2k系列放映机触摸屏与日志中的故障错误代码并译文备查，同时将针对部分常见的对我放映工作有价值的故障提供解决方法。需要注意的是，某些代码会同时表示错误和警告，某些表示错误（error），某些是警告（waring）。在“警告”状态下，放映机虽将继续维持运转，但仍建议尽快解决导致“警报”的故障，否则，“警报”状态将有可能引发“错误”的产生，而最终导致停机事故的发生。故障代码列表如下，可用ctrl+f快捷键进行搜索：1.code 5003: “light sensor - no communication” (error)“灯传感器

2、 - 无通讯”2.code 5004: “lamp - no communication” (error)“灯 - 无通讯”状态解决方法灯箱没有被正确安装检查灯箱安装，并重置灯箱使用了与本机型号不匹配的灯箱选择匹配灯箱同时显示代码5180（lamp house - not connected）见5180与灯箱无通讯检查灯箱前端蓝色插头是否损坏3.code 5005: “lamp power supplies - communication failed” (error)“灯电源 - 通讯失败”状态解决方法ctrl in, ctrl out线没有插紧重新连接电源模块上的ctrl接口与接线addr

3、ess线没有插紧重新连接address线主电源输入线没有插紧重新连接两组main input接口与接线其中一组电源红灯快速闪亮更换整组电源模块4.code 5010: “pump - refill mode is on” (warning)“冷却泵 - 补充模式已开启”状态解决方法放映机切换至“补充模式”，只有冷却泵开启等冷却液补充完毕，点击“退出补充模式”5.code 5042: “cold mirror fan - speed too low” (error)“反射镜风扇 - 转速过低”6.code 5043: “cold mirror fan - speed low” (warning)

4、“反射镜风扇 - 转速低”7.code 5052: “engine fan - speed too low” (error)“引擎风扇 - 转速过低”8.code 5053: “engine fan - speed low” (warning)“引擎风扇 - 转速低”9.code 5062: “heat exchanger fan - speed too low” (error)“散热器风扇 - 转速过低”10.code 5063: “heat exchanger fan - speed low” (warning)“散热器风扇 - 转速低”11.code 5072: “lamp anode

5、fan - speed too low” (error)“灯阳极风扇 - 转速过低”12.code 5073: “lamp anode fan - speed low” (warning)“灯阳极风扇 - 转速低”13.code 5082: “lamp cathode fan - speed too low” (error)“灯阴极风扇 - 转速过低”14.code 5083: “lamp cathode fan - speed low” (warning)“灯阴极风扇 - 转速低”15.code 5102: “smps fan 1 - speed too low” (error)“开关电源风

6、扇1 - 转速过低”16.code 5103: “smps fan 1 - speed low” (warning)“开关电源风扇1 - 转速低”17.code 5112: “smps fan 2 - speed too low” (error)“开关电源风扇2 - 转速过低”18.code 5113: “smps fan 2 - speed low” (warning)“开关电源风扇2 - 转速低”19.code 5122: “lamp rear fan - speed too low” (error)“灯后部风扇 - 转速过低”20.code 5123: “lamp rear fan -

7、speed low” (warning)“灯后部风扇 - 转速低”21.code 5132: “elcabox fan - speed too low” (error)“电控盒风扇 - 转速过低”22.code 5133: “elcabox fan - speed low” (error)“电控盒风扇 - 转速低”23.code 5160: “engine switch - not ok” (error)“引擎开关 - 不正常”24.code 5170: “fib - not connected” (error)“解码板- 未连接”25.code 5180: “lamp house - not

8、 connected” (error)“灯箱 - 未连接”状态解决方法灯箱未正确安装检查灯箱是否已正确牢固安装，确认三颗锁定螺丝已锁紧开关损坏或未接触检查灯箱右下角固定螺丝对应的放映机内侧微动开关是否损坏或未接触风扇控制板失灵更换26.code 5191: “prism switch - warning (lens probably touches prism)” (warning)“棱镜开关 - 警告（镜头可能已触动棱镜）”状态解决方法镜头转动至极限，已触动到棱镜传感器重新调整镜头位置棱镜传感器失效拆除镜头并重启放映机，若仍有警告则为棱镜传感器失效27.code 5212: “pump -

9、speed too low” (error)“冷却泵 - 转速过低”28.code 5213: “pump - speed low” (warning)“冷却泵 - 转速低”29.code 5230: “lens zoom position - requested target not reached” (warning)“镜头变焦位置 - 没有达到预定位置”状态解决方法所使用的为手动镜头更换电动镜头并设置镜头参数已激活镜头文件无法驱动已安装镜头检查镜头型号设置是否正确镜头文件损坏删除并重建所有现有镜头文件镜头预定位置已非常接近电动镜头机械极限手动重置镜头，或重置放映机位置镜头马达失灵使用小面

10、板上的镜头位置控制按钮，若无反应，则为镜头马达失灵30.code 5232: “lens horizontal shift position - requested target not reached” (warning)“镜头水平移动位置 - 没有达到预定位置”状态解决方法镜头文件损坏参见5230镜头预定位置已非常接近电动镜头机械极限手动重置镜头，或重置放映机位置镜头马达失灵使用小面板上的镜头位置控制按钮，若无反应，则为镜头马达失灵31.code 5233: “lens vertical shift position - requested target not reached” (war

11、ning)“镜头垂直移动位置 - 没有达到预定位置”参见523232.code 5237: “lens position - clear requested target time out failed” (warning)“镜头位置 - 接受明确指令超时”33.code 5280: “ambient - temperature too high” (error)“环境 - 环境温度过高”状态解决方法前滤网堵塞清洗或更换环境温度过高降低环境温度抽风设备失灵修复抽风设备34.code 5281: “ambient - temperature high” (warning)“环境 - 环境温度高”

12、参见528035.code 5283: “ambient - temperature low” (warning)“环境 - 温度低”36.code 5284: “ambient - temperature sensor open” (error)“环境 - 环境温感器断路”37.code 5285: “ambient - temperature sensor short” (error)“环境 - 环境温感器短路”38.code 5290: “dmd blue - temperature too high” (error)“蓝dmd - 温度过高”39.code 5291: “dmd blu

13、e - temperature high” (warning)“蓝dmd - 温度高”40.code 5293: “dmd blue - temperature low” (warning)“蓝dmd - 温度低”41.code 5294: “dmd blue - temperature sensor open” (error)“蓝dmd - 温感器断路”42.code 5295: “dmd blue - temperature sensor short” (error)“蓝dmd - 温感器短路”43.code 5300: “dmd green - temperature too high”

14、 (error)“绿dmd - 温度过高”44.code 5301: “dmd green - temperature high” (warning)“绿dmd - 温度高”45.code 5303: “dmd green - temperature low” (warning)“绿dmd - 温度低”46.code 5304: “dmd green - temperature sensor open” (error)“绿dmd - 温感器断路”47.code 5305: “dmd green - temperature sensor short” (error)“绿dmd - 温感器短路”4

15、8.code 5310: “lamp - temperature too high” (error)“灯 - 温度过高”状态解决方法滤网堵塞清洗或更换滤网环境温度过高降低环境温度抽风设备失灵修复抽风设备氙灯阴/阳极风扇失灵检查阴/阳极风扇转速及电压49.code 5311: “lamp - temperature high” (warning)“灯 - 温度高”参见531050.code 5314: “lamp - temperature sensor open” (error)“灯 - 温感器断路”51.code 5315: “lamp - temperature sensor short”

16、 (error)“灯 - 温感器短路”52.code 5320: “fcb - force lps off” (error)“风扇控制板 - 灯电源强制关闭”53.code 5330: “pfc heatsink - temperature too high” (error)“散热器 - 温度过高”54.code 5331: “pfc heatsink - temperature high” (warning)“散热器 - 温度高”55.code 5340: “dmd red - temperature too high” (error)“红dmd - 温度过高”56.code 5341: “

17、dmd red - temperature high” (warning)“红dmd - 温度高”57.code 5343: “dmd red - temperature low” (warning)“红dmd - 温度低”58.code 5344: “dmd red - temperature sensor open” (error)“红dmd - 温感器断路”59.code 5345: “dmd red - temperature sensor short” (error)“红dmd - 温感器短路”60.code 5350: “smps primary heatsink - temper

18、ature too high” (error)“开关电源主散热器 - 温度过高”61.code 5351: “smps primary heatsink - temperature high” (warning)“开关电源主散热器 - 温度高”62.code 5360: “smps secundary heatsink - temperature too high” (error)“开关电源副散热器 - 温度过高”63.code 5361: “smps secundary heatsink - temperature high” (warning)“开关电源副散热器 - 温度过高”64.cod

19、e 5364: “smps secundary heatsink - temperature sensor open” (error)“开关电源副散热器 - 温感器断路”65.code 5365: “smps secundary heatsink - temperature sensor short” (error)“开关电源副散热器 - 温感器短路”66.code 5401: “+30v - voltage high” (warning)“+30v - 电压高”67.code 5403: “+30v - voltage low” (warning)“+30v - 电压低”68.code 54

20、11: “+5v - voltage high” (warning)“+5v - 电压高”69.code 5413: “+5v - voltage low” (warning)“+5v - 电压低”70.code 5431: “cold mirror fan - voltage high” (warning)“反射镜风扇 - 电压高”71.code 5432: “cold mirror fan - voltage too low” (error)“反射镜风扇 - 电压过低”72.code 5433: “cold mirror fan - voltage low” (warning)“反射镜风扇

21、 - 电压低”73.code 5441: “engine fan - voltage high” (warning)“引擎风扇 - 电压高”74.code 5442: “engine fan - voltage too low” (error)“引擎风扇 - 电压过低”75.code 5443: “engine fan - voltage low” (warning)“引擎风扇 - 电压低”76.code 5451: “heat exchanger fan - voltage high” (warning)“换热器风扇 - 电压高”77.code 5452: “heat exchanger f

22、an - voltage too low” (error)“换热器风扇 - 电压过低”78.code 5453: “heat exchanger fan - voltage low” (warning)“换热器风扇 - 电压低”79.code 5461: “lamp anode fan - voltage high” (warning)“灯阳极风扇 - 电压高”80.code 5462: “lamp anode fan - voltage too low” (error)“灯阳极风扇 - 电压过低”81.code 5463: “lamp anode fan - voltage low” (wa

23、rning)“灯阳极风扇 - 电压低”82.code 5471: “lamp cathode fan - voltage high” (warning)“灯阴极风扇 - 电压高”83.code 5472: “lamp cathode fan - voltage too low” (error)“灯阴极风扇 - 电压过低”84.code 5473: “lamp cathode fan - voltage low” (warning)“灯阴极风扇 - 电压低”85.code 5492: “smps fan - voltage too low” (error)“风扇控制板风扇 - 电压过低”86.c

24、ode 5493: “smps fan - voltage low” (warning)“风扇控制板风扇 - 电压低”87.code 5501: “fib +12v - voltage high” (warning)“解码板 +12v - 电压过高”88.code 5503: “fib +12v - voltage low” (warning)“解码板 + 12v - 电压低”89.code 5521: “motor (lens, dowser) - voltage high” (warning)“马达（镜头、光闸） - 电压高”90.code 5523: “motor (lens, dows

25、er) - voltage low” (warning)“马达（镜头、光闸） - 电压低”91.code 5531: “pump - voltage high” (warning)“冷却泵 - 电压高”92.code 5532: “pump - voltage too low” (error)“冷却泵 - 电压过低”93.code 5533: “pump - voltage low” (warning)“冷却泵 - 电压低”94.code 5551: “tec - voltage high” (warning)“珀耳贴致冷器 - 电压高”95.code 5553: “tec - voltage

26、 low” (warning)“珀耳贴致冷器 - 电压低”96.code 5561: “elcabox fan - voltage high” (warning)“电控盒风扇 - 电压高”97.code 5562: “elcabox fan - voltage too low” (error)“电控盒风扇 - 电压过低”98.code 5563: “elcabox fan - voltage low” (warning)“电控盒风扇 - 电压低”99.code 5571: “lamp rear fan - voltage high” (warning)“灯后部风扇 - 电压高”100.code

27、 5572: “lamp rear fan - voltage too low” (error)“灯后部风扇 - 电压过低”101.code 5581: “+12v - voltage high” (warning)“+12v - 电压高”102.code 5583: “+12v - voltage low” (warning)“+12v - 电压低”103.code 5640: “lamp power supplies - zero lamp power supplies detected” (error)“灯电源 - 没有探测到灯电源”状态解决方法两电源模块其中之一主供电电缆断开检查电源模

28、块上mains input插槽及插线电源模块中“ctrl in”与“ctrl out”插线断开检查电源模块中“ctrl in”与“ctrl out”插槽及插线电源模块未安装到位重新安装灯电源控制板失灵更换灯电源模块闪红灯更换电源模块104.code 5641: “lamp power supplies - lamp is on, but smps is off” (error)状态解决方法开关电源板失灵更换灯电源模块失灵更换电源背板失灵更换105.code 5642: “lamp power supplies - at least one lamp power supply could not

29、 be detected” (error)参见5640106.code 5643: “lamp power supplies - communication failed with at least one lamp power supply”(error)参见5640107.code 5644: “lamp power supplies - lamp is on, but at least one lamp power supply is off” (error)参见5640108.code 5646: “lamp - set lamp on failed” (error)“灯 - 点灯失败

30、”状态解决方法氙灯有触发，无法持续点燃1，氙灯寿命将尽，更换新灯2，触发器损坏109.code 5647: “lamp - lamp is off due to an error” (error)“灯 - 由于一个错误氙灯已熄灭”状态解决方法由于某些错误，灯电源被指令熄灭氙灯查看放映机日志寻找其他错误信息，首先解决此类错误问题灯电源故障查看灯电源指示灯，若红灯闪烁则更需换灯电源氙灯缺陷更换新灯110. code 5654: “lamp run time - read failed” (error)“灯运行时间 - 读取失败”111. code 5657: “lamp run time - ex

31、ceeds maximum” (error)“灯运行时间 - 已到最大寿命”状态解决方法灯箱内氙灯已达到最大使用寿命更换新灯，或重置灯信息112.code 5658: “lamp run time - read limits failed” (error)“灯运行时间 - 限制读取失败”113. code 5659: “lamp run time - warning” (warning)状态解决方法灯箱内氙灯接近到最大使用寿命尽快更换新灯，或重置灯信息114. code 5800: “ti-boards - system status = fail” (error)“ti板 - 系统状态=失败

32、”这是一个通用ti错误代码，需要进入触摸屏的“诊断-测试-自检”中勾选所有选项并进行检测，并将检测结果提供给服务商用以查找具体故障所在。115. code 5801: “ti-boards - security error, please authorize” (error)“ti板 - 安全错误，请授权”状态解决方法放映机的输入或通讯组件被物理重置使用授权钥匙进行重新授权，步骤如下1，确保重置部件正确安装2，开启放映机3，将授权钥匙嵌入授权插槽4，在5秒内输入口令放映机内盖被拆开（光处理器部分）方法同上安全开关失灵如果执行以上方法仍无效，更换dci安全开关电源背板失灵如果更换安全开关无效则更

33、换电源背板116.code 5802: “ti-boards - power up self test = fail” (error)“ti板 - 开机自检 - 失败”117. code 5803: “ti-boards - interface board arm status = fail” (error)“ti板 - 接口板装载状态 = 失败”118. code 5804: “ti-boards - interface board fpga load status = fail” (error)“ti板 - 接口板fpga装载状态 = 失败”119. code 5805: “ti-boar

34、ds - processor board dsp status = fail” (error)“ti板 - 运算板dsp状态 = 失败”120. code 5806: “ti-boards - processor board fpga load status = fail” (error)“ti板 - 运算板fpga装载状态 = 失败”121. code 5807: “ti-boards - read system status failed” (error)“ti板 - 系统状态读取失败”122. code 5810: “ti-boards - read power-good failed”

35、 (error)“ti板 - 读取电源状态失败”123. code 5811: “ti-boards - power-good = fail” (error)“ti板 - 电源正常信号 = 失败”124. code 5820: “ti-boards - interface board security enclosure error - replace interface board” (error)“ti板 - 接口板安全外壳错误 - 更换接口板”125. code 5880: “dolby 3d key-server - read status failed” (warning)“杜比3d

36、服务 - 状态读取失败”126. code 5881: “dolby 3d key-server - status = locked” (warning)“杜比3d服务 - 状态 = 锁定”127. code 5882: “3d module - read status failed” (warning)“杜比3d模块 - 状态读取失败”128. code 5885: “3d module - change status failed due to communication error” (error)“杜比3d模块 - 由于通讯故障导致的状态更新失败”129.code 5890: “3d

37、module - color wheel spin failed” (error)“杜比3d模块 - 色轮旋转失败”130.code 5891: “3d module - color wheel in failed” (error)“杜比3d模块 - 色轮嵌入失败”131. code 5892: “3d module - color wheel out failed” (error)“杜比3d模块 - 色轮撤出失败”132. code 5893: “3d module - color wheel temperature too high” (error)“杜比3d模块 - 色轮温度过高”133

38、. code 5894: “3d module - color wheel speed not ok (not locked)” (error)“杜比3d模块 - 色轮转速不正常（未锁定）”134. code 5960: “light pipe - temperature too high” (error)“光路 - 温度过高”状态解决方法液冷循环中断检查液冷循环管道是否正常光处理器的液冷管道被错误连接将光处理器的液冷管道与冷却泵和换热器重新连接冷却泵未启动检查冷却泵电压换热器的抽气滤网堵塞清理或更换放映机下部的滤网冷却液不足，冷却泵抽气并且运行声音变大排除冷却循环中的空气，重新添加冷却液液冷

39、循环系统故障，开启补充模式时感觉不到冷却泵的振动1，检查泵电压2，排出所有冷却液，打开冷却泵查看其转子是否被阻塞温感器失灵更换氙灯位置有误重新调整氙灯位置反射镜位置有误调整反射镜位置135. code 5961: “light pipe - temperature high” (warning)“光路 - 温度高”同5960136. code 5964: “light pipe - temperature sensor open” (error)“光路 - 温感器断路”137. code 5965: “light pipe - temperature sensor short” (error)

40、“光路 - 温感器短路”138.code 5970: “dmd red front - temperature too high” (error)“红dmd前端 - 温度过高”139. code 5971: “dmd red front - temperature high” (warning)“红dmd前端 - 温度高”140. code 5973: “dmd red front - temperature low” (warning)“红dmd前端 - 温度低”141. code 5974: “dmd red front - temperature sensor open” (error)

41、“红dmd前端 - 温感器断路”142. code 5975: “dmd red front - temperature sensor short” (error)“红dmd前端 - 温感器短路”143. code 5980: “dmd green front - temperature too high” (error)“绿dmd前端 - 温度过高”144. code 5981: “dmd green front - temperature high” (warning)“绿dmd前端 - 温度高”145. code 5983: “dmd green front - temperature

42、low” (warning)“绿dmd前端 - 温度低”146. code 5984: “dmd green front - temperature sensor open” (error)“绿dmd前端 - 温感器断路”147. code 5985: “dmd green front - temperature sensor short” (error)“绿dmd前端 - 温感器短路”148. code 5990: “dmd blue front - temperature too high” (error)“蓝dmd前端 - 温度过高”149. code 5991: “dmd blue f

43、ront - temperature high” (warning)“蓝dmd前端 - 温度高”150. code 5993: “dmd blue front - temperature low” (warning)“蓝dmd前端 - 温度低”151. code 5994: “dmd blue front - temperature sensor open” (error)“蓝dmd前端 - 温感器断路”152. code 5995: “dmd blue front - temperature sensor short” (error)“蓝dmd前端 - 温感器短路”153. code 6000: “block front - temperature too high” (error)“前冷却块 - 温度过高”154. code 6001: “block front - temperature high” (warning)“前冷却块 - 温度高”155. code 6004: “block front - temperature sensor open” (error)“前冷却块 - 温感器断路”156. code 6005: “block front - temperature sensor short” (error)“前冷却块