




版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、以下文档格式全部为 word 格式,下载后您可以任意修改编辑。摘要本次设计主要是对中型客车制动系统结构进行分析的基础上,根据对 中型客车制动系统的要求,设计出合理的符合国家标准和行业标准的制动 系统。汽车制动系统是汽车最重要的系统之一,它直接关系到汽车行驶的 安全性。为了保证汽车行驶的安全,制动器性能的好坏成为汽车构造中的 重中之重。同时,良好的制动系统还能提高汽车的方向稳定性和制动效能。首先制定出制动系统的结构方案设计计算确定前盘、后鼓式制动器。 绘制出了前、后制动器装配图、制动阀装配图、制动管路布置图。最终对 设计出的制动系统的各项指标进行评价分析。通过本次设计的计算结果表明设计出的制动系
2、统是合理的、符合标准 的。其满足结构简单、成本低、工作可靠等要求。关键词: 中型客车;制动系统设计;盘式制动器;鼓式制动器;气压 系统;AbstractBased on the structural analysis and the design requirements of n.medium bus braking system,a braking systemdesign is performed in this thesis, according to the national and professionalstandards. Automotive vehicle braking
3、system is one of the most important system, it is directly related to car driving safety. In order to ensure the safety of automobile travel, automobile brake performance is good or bad to become a top priority in construction. At the same time, good braking system can improve the cars directional s
4、tability and braking performance.The braking system design starts from determination of the structure scheme.Calculating and determining the main dimension and structural type of thefront disc、 drum brake, brake master cylinder,and therefore draw the engineering drawings of the front and rear brakes
5、, Brake valve, the diagram of the brake pipelines.The results show the design of braking system is reasonable, consistent with the standards and satisfies the requests such as simple structure and low cost.Key words: Medium-sized passenger car; braking system design; disc brake; drum brake; pneumati
6、c system;目录摘要 IAbstract II第1章绪论 11.1制动器设计的意义及目的 11.2汽车制动系统设计的要求 11.3汽车制动系统的组成 11.4制动系工作原理 21.5制动器研究现状 2第2章汽车制动方案论证分析与选择 42.1制动器形式方案分析 42.1.1鼓式制动器结构形式 42.1.2盘式制动器结构形式 62.2制动驱动机构的结构型式与选择 82.2.1简单制动系82.2.2 动力制动系92.2.3 伺服制动系92.3液压分路系统的形式与选择 10第3章 制动系统主要参数的确定 123.1中型客车主要技术参数 123.2同步附着系数的的确定 123.3前、后轮制动力分
7、配系数的确定。 133.4盘式制动器主要参数的确定 133.5制动器最大制动力的确定 143.6盘式制动器制动因数计算 143.7鼓式制动器的设计计算 153.8鼓式制动效能因素计算 153.9制动器的温升计算 163.10盘式制动器主要零部件的结构设计 173.11鼓式制动器主要零部件的结构设计 18第4章气压制动系统结构设计与分析 204.1气压制动系统结构 204.1.1气压制动回路204.1.2 供能装置 204.1.3 控制装置 214.1.4制动气室 234.2气压驱动机构的设计与计算 244.2.1制动气室设计244.2.2贮气筒254.2.3空气压缩机的选择 25第5章制动性能
8、评价分析 265.1制动性能评价指标 265.2制动效能 265.3制动效能的恒定性 275.4制动时汽车的方向稳定性 275.5前、后制动器制动力分配 285.5.1 地面对前、后车轮的法向反作用力 285.5.2 理想的前、后制动器制动力分配曲线 295.5.3实际的前、后制动器制动力分配曲线 29第6章总论 30参考文献 31致谢 32附录1 33附录2 38第1章 绪 论1.1 制动器设计的意义及目的汽车制动系统是汽车最重要的系统之一,它直接关系到汽车行驶的安 全性。随着汽车性能的提高,汽车的时速越来越高,为此,交通事故也逐 年增加。在汽车交通事故中,除去违章驾驶以外,最主要原因就是车
9、辆机 械故障,而在各种交通故障中制动失灵占有相当高的比例。可见,制动机 构是保证行车安全的极为重要的系统。为了保证汽车行驶的安全,制动器 性能的好坏成为汽车构造中的重中之重。同时,良好的制动系统还能提高 汽车的方向稳定性和制动效能。因此,提高汽车制动性能具有一定的实际 应用意义,与此同时,掌握汽车制动器设计具有一定的理论意义。制动器设计的目的:1、通过查阅相关的资料,运用专业基础理论和专业知识,确定中型客车 制动系统的设计方案,进行部件的设计计算和结构设计。2、达到综合运用所学知识分析汽车基本性能和部件设计的训练, 为今后实 际工作打下基础。1.2 汽车制动系统设计的要求1、保证客车具有足够的
10、制动效能,客车在 30km B.Rae.The AmericanAutomobile IndustryM.Boston:Twayne Publishers,1984Automobiles and TrucksM.Virginia:Reston PublishingCompany,Inc.,1982 14 张洪图 . 汽车构造底盘部分 . 北京:北 京理工大学出版社, 1996,915Oldham,J.Auto Trouble ShooterM.New York:The Hearst Corporation,1976致谢论文的完成标志着我的学生时代即将结束,从刚到大学到即将毕业感 觉时间是过的那
11、么快,真的好想继续在学校学习,与老师同学一起生活, 在次感受大学的美好时光。毕业设计的完成,首先必须感谢我的导师张立军,从开题报告到最后 的审查他给予我的帮助是相当多的。由于工作原因,我的开题报告和数据 计算都是在校外完成的,在那段时间内老师通过电话等方式联系帮助我, 更使我非常感动。在老师辅导我的过程中,老师的知识渊博更让我佩服无 比,在做毕业设计的过程中遇到什么问题老师都能轻易的帮我解决,在次 感谢张立军老师。其次必须感谢我的答辩老师,虽然答辩的时间很短,次数很少,但是 在那短短的时间呢,各位老师给我意见非常有用,精辟,使我的毕业设计 更加完整,合理,感谢各位答辩老师。还有感谢我的同学,同
12、学的帮助是非常大的,在毕业设计的过程中遇 到了许多问题,我的同学都能非常耐心的给我指导,帮助,并且给我提出 问题帮我改正,感谢我的同学。最后还得感谢我的家人,他们在精神上对我帮助更是不能缺少的,在 我烦恼的时候帮助我放松精神,继续投入到设计当中。再次由衷的感谢各位帮助我的人!BRAKE SYSTEMThe braking system is the most important system in cars. If the brakes fail, the result can be disastrous.Brakes are actually energy conversion device
13、s, which convert the kinetic energy (momentum) of the vehicle into thermal energy (.The typical brake systemconsistsof disk brakes in front and either disk or drum brakes in the rear connected by a system of tubes and the brake pedal, a plunger is actually been pushing against in the master cylinder
14、 which forces be directed through many twists and turns on its way to its destination, arriving with the exact same motion and pressure that it started with. It is very important that the fluid is pure liquid and that there are no air bubbles in it. Air can compress,which causesa sponginessto the pe
15、dal and severely reduced braking efficiency.If air is suspected,then the system must be bled to remove the air. There are “ bleeder screws ” at each wheel cylinder and caliper for this purpose.With drum brakes, fluid is forced into the wheel cylinder which pushes the brake shoes out so that the fric
16、tion linings are pressed against the drum which is attached to the wheel, causing the wheel to stop.On a disk brake, the fluid from the master cylinder is forced into a caliper where it presses against a piston. The piston, in-turn, squeezes two brake pads against the disk(rotor)which is attached to
17、 the wheel, forcing it to slow down or stop. This process is similar to a bicycle brake where two rubber pads rub against the wheel rim creating friction.In either case, the friction surfaces of the pads on a disk brake system, or the shoeson a drum brake convert the forward motion of the vehicle in
18、to surfaces (linings) of the padsand shoes to eventuallywear out and require replacement.Drum BrakesSo if disk brakes are so great, is cost. While all vehicles produced for many years the front, drum brakes are cheaper to produce for the rear wheels. The main reason is the parking brake system. On d
19、rum brakes, adding a parking brake is the simple addition of a lever, while on disk brakes, we need a complete mechanism, in some cases, a complete mechanical drum brake assembly inside the disk brake rotor! Parking brakes must be a separate system that does not useparking brakes later Wheel Cylinde
20、rThe wheel cylinder consists of a cylinder that each side. Each piston with a brake shoe. When brake pressure is applied, the pistons are forced out pushing the shoes into contact with the drum. Wheel cylinders must be rebuilt or replaced if they show signs of leaking.Brake ShoesLike the disk pads,
21、brake shoesconsistof a steel shoe with the friction material or lining riveted or bonded to it. Also like disk pads, the linings eventuallywear out and must be replaced. If the linings are allowed to wear through to the bare metal shoe, they will cause severe damage to the brake drum.Backing PlateTh
22、e backing plate is what virtually every car made. On most cars, the front brake are of the disc type, and the rear barkes are of the “ drum” type. Drum brakes use two semi-circular shoes to press outward against the inner surfaces of a steel drum. Older cars often all four wheels, and many new the s
23、ame basic principles to slow a vehicle (friction and is far superior to that of drum brakes. Becausedisc brakes can fling off water more easily than drum brakes, they work much better in wet conditions. This is not to say that water does not affect them, it definitely does. If you splash through a p
24、uddle and then try to apply the brakes, your brakes may not work at all for a few seconds!Disc brakes also allow better airflow cooling, which also increasestheir effectiveness.Some most cars in the early seventies.译文制动系统制动系统是汽车中主要的系统之一。 如果制动损坏, 结果可能是惨重的。制动器是能量转换装置, 它将汽车的动能 (动量)转化成热能 (热量)。制动系统是由下列基本
25、的成分组成 : “制动主缸” “制动管路” “制动 软管”“制动轮缸” “制动盘”和“衬块”等等。典型的制动系统布置有前后盘式,前盘后鼓式,各个车轮上的制动器 通过一套管路系统连接到制动主缸上。踩着制动踏板时,事实上是制动主缸中的活塞通过一连串的管路和软 管强制液压油(制动液)推入到每个轮子上。 因为液压油液 ( 或任何的流 动性的物质而言 )不能够被压缩 , 推动液体经过一个管路就像推动一个钢 筋通过一个管路。然尔,与钢筋不同的是液体可以直接通过许多弯曲的地 方并可以任意改变方向,像它开始的那样以相同的精确的压力和运动到达 某个地方。非常重要的是,液体是纯粹的液体而且没有空气泡沫在它里面。当
26、空气被压缩,引起制动踏板的迟疑,并减少制动效率。如果怀疑有空气, 那么系统就会放出空气,每个车轮上的放气螺钉和卡钳就是这个目的。在盘式制动器中,主缸中的液体被迫压缩到活塞中。 活塞作往复运动, 挤压这两个制动块和连接着车轮的制动蹄。 这个过程类似于自行车的刹车, 自行车的两个橡胶板作用在车轮上制造摩擦。鼓式制动器,流体是被迫进入轮缸,推动制动蹄片向外运动,使摩擦 衬垫作用于连接车轮的制动鼓。使车轮停止。无论哪一种情况,盘式制动系中的摩擦表面,还是鼓式制动器中的制 动鼓都是把车轮的往复运动转变为热能。热能就是使制动衬垫和制动蹄上 的摩擦消失并且代替。鼓式制动器如果盘式制动器市场很大,为何我们仍然
27、使用鼓式制动器?原因在于 成本。而所有车辆零件的生产,多年来采用前盘式,后轮生产鼓式是由于它的价 格低。主要的原因是停车制动系统。在鼓式制动器上,增加的一个驻车制 动是一个很简单手柄,而在盘式制动器上,我们需要一个完整的机制,在 某些情况下,一个完整的机械鼓式制动器内也有盘式制动器的配件!驻车 制动器必须是一个不使用液压独立的系统。它必须完全机械,但更多的用 在停车制动器。轮缸轮缸里有两个对称布置活塞。每个活塞有一个橡胶密封件,和连接活 塞的活塞杆。当制动压力一定时,活塞被迫推动液压与制动蹄接触,从而 实现制动。制动瓦像磁盘丝带、制动瓦是由钢制成的摩擦材料或衬内的铆钉组成。像磁 盘丝带一样,摩擦衬片也有坏的
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 传统纺织工艺研究:手工印染技术的历史传承与创新应用
- 民警打分具体管理办法
- 供水公司主业管理办法
- 法兰西国族认同研究:从“国族传奇”看历史演变
- 民国茶叶消费量与产量动态关系研究
- 内部湿度差异对硬化水泥浆体特性的影响研究
- 公共物品维护管理办法
- 变频器效率优化-洞察及研究
- 跨界共生:“双师型”教师企业实践激励机制创新探讨
- 鞭毛状微生物阪崎肠杆菌的乳粉检测技术研究
- 办公室应聘题库及答案
- 2025年河北中考地理真题含答案
- 铁矿尾矿清运方案(3篇)
- 国开机考答案 管理学基础2025-06-27
- 国家开放大学《思想道德与法治》社会实践报告范文一
- 【9语安徽中考卷】2025年安徽省中考招生考试真题语文试卷(真题+答案)
- 2025年空气过滤器行业分析报告
- 同等学力人员申请硕士学位电子科学与技术学科综合水平全国统一考试大纲(第二版)
- (高清版)DG∕TJ 08-507-2018 高强混凝土抗压强度无损检测技术标准
- 2024年铁岭市三支一扶考试真题
- 2024版机电工程施工质量标准化数字模型图集
评论
0/150
提交评论