加工中心精度检验规范

1、NO沛電腦配件（海）有限公司静态精度 STATIC ACCURACY INSPECTION单位 Unit : mmRI PEI compu ter accessory (Shanghai) Co., Ltd.加工中心精度检验規範机型:MODEL机号:SERIAL NO.目CATALOGUE静态精度检查P AGESTATIC ACCURACY INS PECION 定位精度检查.P AGEP OSITION ACCURACY INS PECTION 重复精度检查.P AGEREP ETITIONAL ACCURACY INS PECTION中國上海松江區新橋鎮申港路 3636號Shen gga

2、ng Road,X in Qiao Son gjia ng Shan ghai China核准者CONFIRMED检验者CHECKED检验 日期DATEMCV F01 S001Q3940331-7测试方法图Measuri ng method diagram项次NO检查项目Insp ecti on item床台X轴 方向运动 之真直度Straight ness of theX axis moveme nta.X-Z面内b.Y-Z面内床台丫轴方向运动之真直度a.Straight nX-Zess of the面内丫 axismoveme ntb.Y-Z面内许可差P ermissibledeviati

3、o n实 际测量值Measured value100010001-4单位 Unit : mmNOP arallelismbetwee nand table upper surfaceaxis direct ion检查项目Insp ecti on item床台X轴方向之 运动与其上面之 平行度movement inX许可差P ermissible deviati onX 三 500500V X 三 800800V X 三 12501250V X 三 2000实 际测量值Measured valueP arallelismbetwee nmovement inand table upper sur

4、faceaxis direct ion床台丫轴方向之 运动与其上面之 平行度Y丫三 500500V 丫三 800800V 丫三 12501250V 丫三 2000X轴方向运动与床 台基准沟侧面之 平行度P arallelismbetwee nmovement inaxis direct ionand Side surfaceoftablerefere nee slotX每300mmf勺量测距离下许可差为a measuri nglen gth of 300测试方法图Measuri ng method diagram项次NO检查项目Insp ecti on item各轴方向 相互运动 之直角度Pe

5、rpen dic ularity Betwee n moveme nt in X axis direct ion and Y axis direct ion and Z axis direct iona.X-Y轴P laceb.X-Z轴P lacec.Y-Z轴P lace主轴中心线与床 台面之直角度Perpen dicularit y betwee n cen terl ine of main spin dle and table surface.许可差P ermissibledeviati on实 际测量值Measured value300300300旋径每300Per3001-6单位 Un

6、it : mm测试方法图Measuri ng method diagram项次NO检查项目Insp ecti on item许可差P ermissible deviati on实 际测量值Measured value主轴孔内面之偏 摆Run out ofspin dle taper hole主轴轴线与Z轴轴 线运动间的平行 度P arallelism betwee n the spin dle axis and the Z-axis moti on主轴在Z轴方向之 移（松）动量Moveme nt of main spindle in Z axis direct ion主轴端面之偏摆Run ou

7、t of main spin die outer surfaceAt spin dle side end of test bar1-4固定端固定端300处At 300 positiona:300b:300主軸外面之偏擺Run out of mainspin dlesurfaceouter床檯X軸方向運動 之直線度Straight ness of tablemoveme npdge as the figure shown.a fixed indicator to the straightin the X axis.to get reading at both ends of thestraigh

8、t edge.the table 300 mmn X-axis direction.the largest value difference as themeasurement value.300床檯丫軸方向運動 之直線度a fixed indicator to the straightStraight ness oftablemoveme nh。get reading at both ends of theedge as the figure shown.in the Y axisstraight edge.300the table 300 mmn X-axis direction.the

9、largest value difference as themeasurement value.旋轉檯旋轉偏擺Table runo300旋轉檯旋轉偏擺Table runo ut(Z)1-5車刀角度換刀後 重複定位精度Rep eatabilityoftool an gle after tool cha nge.車刀角度停止後 重複定位精度Rep eatabilityoftool an gle after tool stop.刀加工後定位 精*fRep eatabilityoftool angle after machi ning part主軸振動檢測Spin dle vibrati on de

10、tecti on三s(Ref)单位Unit :项 次NO检查项目Inspection item测试方法图Measuri ng method diagram许可差P ermissible deviati on实际测量值Measured value直线运动之 定位精度ISO230-2循环次数：2次XL 三 10001000V L 三 2000L 三 2000定位精度检查 Positioning accuracy inspection mmPo siti oning accuracyofstraightlinemoveme ntByISO230-2Cycletimes:TwotimesYZ单位 Un

11、 it: sec回转运动之定位精度Positi oning accuracy of straight li ne moveme nt By ISO230-2Cycle times:Two timesC151-7单位Un it:反复精度检查 Repetition accuracy inspection sec项 次NO检查项目测试方法图Measuri ng method diagram许可差P ermissibledeviati on实 测Measu际 量值ired valueInspectionitem直线运动之 反复定位精 度ISO230-2Po siti oninXgrep eatabil

12、ity ofstraightlinemoveme ntByISO230-2Cycletimes:TwotimesYZ单位 Un it: sec回转运动之重 复定位精度ISO230-2Po siti oning rep eatability of straight line moveme nt By ISO230-2Cycle times :Two timesC单位Un it:1-8项 次NO检查项目测试方法图Measuri ng method diagram许可差P ermissibledeviati on实 测Measu际 量值ired valueInspectionitemMax reversal value 最大反沖值X反复精度检查 Repetition accuracy inspection sec循圓精度检查 Repetition accuracy inspection sec单位