1055五档转接套齿样件检验报告.doc

dabg-zb-91注：粗线框内由东安动力填写，本报告一式四联。区 分样品种类送检日期： 年 月 日判定日期： 年 月 日样件检验报告新开发件半 成 品设计变更件成 品工程变更件改进产品关键重要一般 更改单日期： ；更改单编号： ；图面版本号：供方：重庆市江汇机械有限责任公司 (第 1 次送样)样品数量：5件 试生产产量：机型：dabs10-5 件号：bs10-4-1701055 件名：五档转接套齿 样品重量： 128 g报告内容：尺寸检验 材质报告 性能试验 耐久试验 统计资料 外观件报告 其它送审理由：新开发件样件标识方法及编号使用材料核准审核填表粉末冶金smf5040-jis z 2550-1983东安综合判定核准审核填表合格判定内容：条件合格不合格简图及说明：按规范要求项目所作成之材料、成分、物性、性能试验等报告难以记载本报告以任意格式附纸于后。粗线框内由da填写。检 验 报 告（续页）dabg-zb-91注：粗线框内由东安动力填写机型：dabs10-5 件号：bs10-4-1701055 名称：五档转接套齿序号检验项目规 格12345678910判定1油槽圆弧深度21.962.041.962.002.002.001.961.962.042.001.9920.00092油槽圆弧半径r33.003.043.002.942.943.023.022.942.943.022.9860.001523距离19.919.8019.8019.8019.8619.7819.7819.7819.7819.8219.7819.7980.00064宽度5.150.05（三处）5.145.165.165.125.165.125.125.145.145.165.1420.000285距离5.050.24.924.884.884.925.144.885.065.064.924.884.9540.008246厚度55.044.985.0044.985.024.985.025.024.985.025.00440.000467厚度16.450.0516.4616.4216.4416.4216.4416.4216.4616.4616.4416.4216.4380.000288端面跳动0.10.070.080.080.090.070.090.080.070.080.070.0780.000069深度1010.0410.009.9610.049.969.969.9610.0010.0410.04100.0012810跳动0.20.150.120.100.150.150.120.150.120.120.100.1280.0003811外花键大径51.651.56551.52551.5751.5551.56551.57551.5651.5551.56551.5751.55950.0001912直径28.528.5628.4428.5628.5228.4428.5228.4428.5628.4428.5228.50.0026413内花键大径2019.94519.93019.93519.9419.94519.93019.93519.94519.94019.93519.9380.0000314跳动0.10.080.090.090.090.070.080.080.070.090.080.0820.0000615厚度180.2517.8618.1418.0217.8817.9218.1217.8617.8818.0218.1417.9840.0126216厚度8.258.228.208.228.248.208.208.228.208.248.208.2140.0002417外径2828.0828.1027.9228.1027.9428.0828.1227.8827.9027.9228.0040.0087818内径4444.2444.1844.0644.2444.1244.1844.2444.0644.1244.2244.1660.0046419油槽深度11.061.000.941.061.060.941.001.000.941.0010.00216检 验 报 告（续页）dabg-zb-91：粗线框内由东安动力填写机型：dabs10-5 件号：bs10-4-1701055 名称：五档转接套齿序号检验项目规 格12345678910判定20油槽圆弧r54.964.985.004.965.024.984.985.024.984.984.9860.000421斜角33（3处）33.1533.1032.9333.0532.9532.9533.0733.1033.0532.9533.030.0055822倒角c1（六处）0.980.981.040.981.001.041.000.980.981.041.0020.0006823斜角33（3处）32.9332.9533.1533.0532.9532.9333.0733.1032.9333.0533.0110.0060924外花键小径47.247.0447.0847.0447.1647.0847.0047.1247.1647.0847.1247.0880.002525公法线长度22.3622.3522.3322.3322.3522.3622.3622.3522.3722.3522.3322.3480.0001826外花键综合公差0.050.040.030.040.030.030.040.040.030.040.030.0350.0000327内花键小径1818.0618.1018.0818.1218.0418.1018.1018.0618.0618.1018.0820.000628内花键跨棒距16.06716.1216.0816.1016.0816.1016.0816.1016.1016.1216.0816.0960.0002229内花键综合公差0.050.030.040.040.040.030.030.030.040.030.030.0340.0000230材料组成fec0.30.8cu13ni 28其它131材料密度6.8g/cm32高频淬火深度20.3硬度hrc4050检 验 报 告（续页）