麻花钻头-切削条件参考表

HSS直柄麻花鑽頭-切削條件表,,,,,,,,,,,,,

"鑽深H<3D採用G81鑽孔,鑽深3D<H<5D採用G73鑽孔Q=0.5D,鑽深5D>H採用G83鑽孔Q=0.5D",,,,,,,,,,,,,

,,,,,,,,,,,,,,

鑽頭,鑽頭,"A3,S45C,S50C",,,,"SLD,SKD",,,,"SLD,SKD,D2,SKH9",,,

直徑,刃長,HRC25度以下,,,,HRC25~HRC35,,,,HRC35~HRC40,,,

mm,mm,V,Fr,轉速,進給,V,Fr,轉速,進給,V,Fr,轉速,進給

2.0,29,20,0.050,3185,159,17,0.030,2643,79,11,0.020,1752,35

2.1,29,20,0.055,3033,167,17,0.034,2517,86,11,0.023,1668,38

2.2,33,20,0.060,2895,174,17,0.038,2403,91,11,0.026,1592,41

2.3,33,20,0.065,2769,180,17,0.042,2299,97,11,0.029,1523,44

2.4,35,20,0.070,2654,186,17,0.046,2203,101,11,0.032,1460,47

2.5,35,20,0.075,2548,191,17,0.050,2115,106,11,0.035,1401,49

2.6,37,20,0.080,2450,196,17,0.056,2033,114,11,0.038,1347,51

2.7,37,20,0.085,2359,201,17,0.062,1958,121,11,0.041,1297,53

2.8,39,20,0.090,2275,205,17,0.068,1888,128,11,0.044,1251,55

2.9,42,20,0.095,2196,209,17,0.074,1823,135,11,0.047,1208,57

3.0,42,20,0.100,2123,212,17,0.080,1762,141,11,0.050,1168,58

3.1,42,20,0.104,2055,214,17,0.082,1705,140,11,0.052,1130,59

3.2,42,20,0.108,1990,215,17,0.084,1652,139,11,0.054,1095,59

3.3,45,20,0.112,1930,216,17,0.086,1602,138,11,0.056,1062,59

3.4,45,20,0.115,1873,215,17,0.088,1555,137,11,0.058,1030,60

3.5,45,20,0.118,1820,215,17,0.090,1510,136,11,0.060,1001,60

3.6,48,20,0.121,1769,214,17,0.093,1469,137,11,0.063,973,61

3.7,48,20,0.124,1721,213,17,0.096,1429,137,11,0.066,947,62

3.8,48,20,0.127,1676,213,17,0.099,1391,138,11,0.069,922,64

3.9,51,20,0.131,1633,214,17,0.102,1356,138,11,0.072,898,65

4.0,54,20,0.135,1592,215,17,0.103,1322,136,11,0.075,876,66

4.1,54,20,0.137,1554,213,17,0.104,1289,134,11,0.077,854,66

4.2,54,20,0.139,1517,211,17,0.106,1259,133,11,0.080,834,67

4.3,54,20,0.140,1481,207,17,0.108,1229,133,11,0.084,815,68

4.4,56,20,0.143,1448,207,17,0.110,1202,132,11,0.085,796,68

4.5,56,20,0.145,1415,205,17,0.113,1175,133,11,0.087,778,68

4.6,56,20,0.148,1385,205,17,0.116,1149,133,11,0.089,762,68

4.7,59,20,0.151,1355,205,17,0.119,1125,134,11,0.091,745,68

4.8,59,20,0.155,1327,206,17,0.122,1101,134,11,0.093,730,68

4.9,62,20,0.160,1300,208,17,0.124,1079,134,11,0.097,715,69

5.0,62,20,0.165,1274,210,17,0.126,1057,133,11,0.100,701,70

5.1,62,20,0.166,1249,207,17,0.128,1037,133,11,0.102,687,70

5.2,64,20,0.168,1225,206,17,0.130,1017,132,11,0.104,674,70

5.3,64,20,0.169,1202,203,17,0.132,997,132,11,0.107,661,71

5.4,64,20,0.170,1180,201,17,0.134,979,131,11,0.111,649,72

5.5,64,20,0.172,1158,199,17,0.137,961,132,11,0.115,637,73

5.6,67,20,0.173,1137,197,17,0.140,944,132,11,0.119,626,74

5.7,67,20,0.174,1117,194,17,0.143,927,133,11,0.123,615,76

5.8,67,20,0.176,1098,193,17,0.145,911,132,11,0.126,604,76

5.9,67,20,0.178,1080,192,17,0.148,896,133,11,0.128,594,76

6.0,70,20,0.180,1062,191,17,0.150,881,132,11,0.130,584,76

6.1,70,20,0.183,1044,191,17,0.152,867,132,11,0.131,574,75

6.2,70,20,0.183,1027,188,17,0.153,853,130,11,0.132,565,75

6.3,70,20,0.184,1011,186,17,0.154,839,129,11,0.133,556,74

6.4,73,20,0.184,995,183,17,0.155,826,128,11,0.134,547,73

HSS直柄麻花鑽頭-切削條件表,,,,,,,,,,,,,

"鑽深H<3D採用G81鑽孔,鑽深3D<H<5D採用G73鑽孔Q=0.5D,鑽深5D<H採用G83鑽孔Q=0.5D",,,,,,,,,,,,,

,,,,,,,,,,,,,,

鑽頭,鑽頭,"A3,S45C,S50C",,,,"SLD,SKD",,,,"SLD,SKD,D2,SKH9",,,

直徑,刃長,HRC25度以下,,,,HRC25~HRC35,,,,HRC35~HRC40,,,

mm,mm,V,Fr,轉速,進給,V,Fr,轉速,進給,V,Fr,轉速,進給

6.5,73,20,0.185,980,181,17,0.157,813,128,11,0.135,539,73

6.6,73,20,0.186,965,180,17,0.158,801,127,11,0.136,531,72

6.7,73,20,0.186,951,177,17,0.159,789,125,11,0.137,523,72

6.8,73,20,0.187,937,175,17,0.161,777,125,11,0.138,515,71

6.9,73,20,0.188,923,174,17,0.163,766,125,11,0.139,508,71

7.0,73,20,0.190,910,173,17,0.165,755,125,11,0.140,500,70

7.1,75,20,0.191,897,171,17,0.167,745,124,11,0.141,493,70

7.2,75,20,0.192,885,170,17,0.169,734,124,11,0.142,487,69

7.3,75,20,0.193,873,168,17,0.171,724,124,11,0.143,480,69

7.4,78,20,0.194,861,167,17,0.172,714,123,11,0.144,473,68

7.5,78,20,0.195,849,166,17,0.173,705,122,11,0.145,467,68

7.6,78,20,0.196,838,164,17,0.174,696,121,11,0.146,461,67

7.7,81,20,0.197,827,163,17,0.175,687,120,11,0.147,455,67

7.8,81,20,0.198,817,162,17,0.177,678,120,11,0.148,449,66

7.9,81,20,0.199,806,160,17,0.178,669,119,11,0.149,443,66

8.0,81,20,0.200,796,159,17,0.180,661,119,11,0.150,438,66

8.1,84,20,0.201,786,158,17,0.181,653,118,11,0.152,432,66

8.2,84,20,0.202,777,157,17,0.182,645,117,11,0.153,427,65

8.3,84,20,0.203,767,156,17,0.183,637,117,11,0.154,422,65

8.4,87,20,0.204,758,155,17,0.184,629,116,11,0.155,417,65

8.5,87,20,0.205,749,154,17,0.185,622,115,11,0.157,412,65

8.6,87,20,0.206,741,153,17,0.186,615,114,11,0.159,407,65

8.7,87,20,0.207,732,152,17,0.187,608,114,11,0.162,403,65

8.8,89,20,0.208,724,151,17,0.188,601,113,11,0.163,398,65

8.9,89,20,0.209,716,150,17,0.189,594,112,11,0.164,394,65

9.0,89,20,0.210,708,149,17,0.190,587,112,11,0.165,389,64

9.1,89,20,0.211,700,148,17,0.191,581,111,11,0.166,385,64

9.2,92,20,0.212,692,147,17,0.192,575,110,11,0.167,381,64

9.3,92,20,0.213,685,146,17,0.193,568,110,11,0.168,377,63

9.4,92,20,0.214,678,145,17,0.194,562,109,11,0.170,373,63

9.5,92,20,0.215,670,144,17,0.195,556,109,11,0.172,369,63

9.6,95,20,0.216,663,143,17,0.196,551,108,11,0.173,365,63

9.7,95,20,0.217,657,142,17,0.197,545,107,11,0.174,361,63

9.8,95,20,0.218,650,142,17,0.198,539,107,11,0.176,357,63

9.9,95,20,0.219,643,141,17,0.199,534,106,11,0.178,354,63

10.0,95,20,0.220,637,140,17,0.200,529,106,11,0.180,350,63

10.1,98,20,0.221,631,139,17,0.201,523,105,11,0.181,347,63

10.2,98,20,0.222,624,139,17,0.202,518,105,11,0.182,343,63

10.3,98,20,0.223,618,138,17,0.203,513,104,11,0.183,340,62

10.4,98,20,0.224,612,137,17,0.204,508,104,11,0.184,337,62

10.5,100,20,0.225,607,136,17,0.205,503,103,11,0.185,334,62

10.6,100,20,0.226,601,136,17,0.206,499,103,11,0.186,330,61

10.7,100,20,0.227,595,135,17,0.207,494,102,11,0.187,327,61

10.8,103,20,0.228,590,134,17,0.208,490,102,11,0.188,324,61

10.9,103,20,0.229,584,134,17,0.209,485,101,11,0.189,321,61

HSS直柄麻花鑽頭-切削條件表,,,,,,,,,,,,,

"鑽深H<3D採用G81鑽孔,鑽深3D<H<5D採用G73鑽孔Q=0.5D,鑽深5D<H採用G83鑽孔Q=0.5D",,,,,,,,,,,,,

,,,,,,,,,,,,,,

鑽頭,鑽頭,"A3,S45C,S50C",,,,"SLD,SKD",,,,"SLD,SKD,D2,SKH9",,,

直徑,刃長,HRC25度以下,,,,HRC25~HRC35,,,,HRC35~HRC40,,,

mm,mm,V,Fr,轉速,進給,V,Fr,轉速,進給,V,Fr,轉速,進給

11.0,103,20,0.230,579,133,17,0.210,481,101,11,0.190,318,61

11.1,103,20,0.231,574,133,17,0.211,476,100,11,0.191,316,60

11.2,106,20,0.232,569,132,17,0.212,472,100,11,0.192,313,60

11.3,106,20,0.233,564,131,17,0.213,468,100,11,0.193,310,60

11.4,106,20,0.234,559,131,17,0.214,464,99,11,0.194,307,60

11.5,106,20,0.235,554,130,17,0.215,460,99,11,0.195,305,59

11.6,109,20,0.236,549,130,17,0.216,456,98,11,0.196,302,59

11.7,109,20,0.237,544,129,17,0.217,452,98,11,0.197,299,59

11.8,109,20,0.238,540,128,17,0.218,448,98,11,0.198,297,59

11.9,109,20,0.239,535,128,17,0.219,444,97,11,0.199,294,59

12.0,111,20,0.240,531,127,17,0.220,441,97,11,0.200,292,58

12.1,111,20,0.241,526,127,17,0.221,437,97,11,0.201,290,58

12.2,111,20,0.242,522,126,17,0.222,433,96,11,0.202,287,58

12.3,111,20,0.243,518,126,17,0.223,430,96,11,0.203,285,58

12.4,114,20,0.244,514,125,17,0.224,426,96,11,0.204,283,58

12.5,114,20,0.245,510,125,17,0.225,423,95,11,0.205,280,57

12.6,114,20,0.246,506,124,17,0.226,420,95,11,0.206,278,57

12.7,114,20,0.247,502,124,17,0.227,416,94,11,0.207,276,57

12.8,114,20,0.248,498,123,17,0.228,413,94,11,0.208,274,57

12.9,114,20,0.249,494,123,17,0.229,410,94,11,0.209,272,57

13.0,114,20,0.250,490,122,17,0.230,407,94,11,0.210,269,57

,,,,,,,,,,,,,,

HSS斜柄麻花鑽頭-切削條件表,,,,,,,,,,,,,

"鑽深H<3D採用G81鑽孔,鑽深3D<H<5D採用G73鑽孔Q=5.0mm,鑽深5D<H採用G83鑽孔Q=5.0mm",,,,,,,,,,,,,

,,,,,,,,,,,,,,

鑽頭,鑽頭,"A3,S45C基礎條件",,,,"S55C,YK30基礎條件",,,,"SKD,SLD基礎條件",,,

直徑,刃長,V,Fr,轉速,進給,V,Fr,轉速,進給,V,Fr,轉速,進給

13.5,118,20,0.255,472,108,17,0.233,392,91,11,0.212,259,55

14.0,122,20,0.260,455,106,17,0.235,378,89,11,0.215,250,54

14.5,122,20,0.270,439,107,17,0.237,365,86,11,0.217,242,52

15.0,125,20,0.280,425,107,17,0.240,352,85,11,0.220,234,51

15.5,128,20,0.285,411,105,17,0.242,341,83,11,0.222,226,50

16.0,130,20,0.290,398,104,17,0.243,330,80,11,0.224,219,49

16.5,132,20,0.295,386,102,17,0.246,320,79,11,0.226,212,48

17.0,135,20,0.300,375,101,17,0.246,311,77,11,0.228,206,47

17.5,140,20,0.305,364,100,17,0.249,302,75,11,0.230,200,46

18.0,140,20,0.310,354,99,17,0.249,294,73,11,0.232,195,45

18.5,145,20,0.315,344,98,17,0.252,286,72,11,0.234,189,44

19.0,145,20,0.320,335,97,17,0.252,278,70,11,0.236,184,44

19.5,150,20,0.325,327,96,17,0.255,271,69,11,0.238,180,43

20.0,150,20,0.330,318,95,17,0.260,264,69,11,0.240,175,42

20.5,155,20,0.335,311,94,17,0.262,258,68,11,0.242,171,41

21.0,155,20,0.340,303,93,17,0.264,252,66,11,0.244,167,41

21.5,160,20,0.345,296,92,17,0.266,246,65,11,0.246,163,40

HSS斜柄麻花鑽頭-切削條件表,,,,,,,,,,,,,

"鑽深H<3D採用G81鑽孔,鑽深3D<H<5D採用G73鑽孔Q=5.0mm,鑽深5D<H採用G83鑽孔Q=5.0mm",,,,,,,,,,,,,

,,,,,,,,,,,,,,

鑽頭,鑽頭,"A3,S45C基礎條件",,,,"S55C,YK30基礎條件",,,,"SKD,SLD基礎條件",,,

直徑,刃長,V,Fr,轉速,進給,V,Fr,轉速,進給,V,Fr,轉速,進給

22.0,160,20,0.345,290,90,17,0.268,240,64,11,0.248,159,39

22.5,165,20,0.345,283,88,17,0.270,235,63,11,0.250,156,39

23.0,165,20,0.350,277,87,17,0.272,230,63,11,0.252,152,38

23.5,165,20,0.355,271,87,17,0.274,225,62,11,0.254,149,38

24.0,165,20,0.355,265,85,17,0.276,220,61,11,0.256,146,37

24.5,165,20,0.355,260,83,17,0.278,216,60,11,0.258,143,37

25.0,165,20,0.360,255,83,17,0.280,211,59,11,0.260,140,36

25.5,165,20,0.365,250,82,17,0.282,207,58,11,0.262,137,36

26.0,165,20,0.370,245,82,17,0.284,203,58,11,0.264,135,36

26.5,170,20,0.375,240,81,17,0.286,199,57,11,0.266,132,35

27.0,170,20,0.380,236,81,17,0.288,196,56,11,0.268,130,35

27.5,175,20,0.385,232,80,17,0.290,192,56,11,0.270,127,34

28.0,175,20,0.390,227,80,17,0.292,189,55,11,0.272,125,34

28.5,180,20,0.390,223,78,17,0.294,185,55,11,0.274,123,34

29.0,180,20,0.390,220,77,17,0.296,182,54,11,0.276,121,33

29.5,185,20,0.390,216,76,17,0.298,179,53,11,0.278,119,33

30.0,185,20,0.400,212,76,17,0.300,176,53,11,0.280,117,33

30.5,190,20,0.420,209,79,17,0.320,173,55,11,0.300,115,34

31.0,190,20,0.420,205,78,17,0.320,171,55,11,0.300,113,34

31.5,195,20,0.420,202,76,17,0.320,168,54,11,0.300,111,33

32.0,195