影院库用户手册

1、DCP-2000 and DCP-2K4Digital Cinema ServersUser ManualVersion 1.4The English version of this document is the only legally binding version. Translated versions are not legally binding and are for convenience only.D2K.OM.001822.DRMPage 1 of 177 Doremi LabsVersion 1.4Table of Contents1 INTRODUCTION81.1

2、PURPOSE81.2 SOFTWARE VERSION81.3 CONTACT INFORMATION82 OVERVIEW92.1 FRONT PANEL92.1.1 DCP-2000 Front Panel92.1.2 DCP-2K4 Front Panel103 CINELISTER113.1 PASSWORDS124 NETWORK CONFIGURATION134.1 DEFAULT NETWORK CONFIGURATION134.2 CHANGING THE IP ADDRESS134.3 NETWORK RESTART145 TIME ZONE CONFIGURATION15

3、5.1 CHECKING THE TIME ZONE155.2 CHANGING THE TIME ZONE166CONTROL PANEL176.1 ACCOUNT MANAGER GUI186.1.1 Add a New User Account196.1.2 Edit an Existing User Account216.1.3 Delete an Existing User Account226.2 AUDIO CONFIGURATION226.2.1 Channel Mapping Tab Disabled Configuration Pre-D

4、efined Mapping Configurations.1 4 Channels.2 6 Channels2.3 7 Channels2.4 8 Channels2.5 9 Channels2.6 ISDCF30 Custom Mapping Configuration326.2.2 Advanced Tab336.2.3 SMPTE Packages346.2.4 Interop Packages346.3 CONTENT FEED MANAGER356.3.1 Quick

5、Configuration356.3.2 Scan for Server366.3.3 Advanced Options Button386.3.4 Adding a Server Manually3 Networking the Server(s)396.3.5 Advanced Options416.3.6 Deleting a Server42D2K.OM.001822.DRMPage 2 of 177 Doremi LabsVersion Ingesting from a Server that was Added426.4 CONTENT MANAG

6、ER446.4.1 Home Page456.4.2 Composition Playlists Page4 Actions Button4 Info Button5.1 Properties Tab5.2 Assets Tab5.3 SPL(s) Tab5.4 KDM(s) Tab586.4.3 Search Tool616.4.4 Decryption Keys Page626.4.5 Performing a KDM SaCheck646.4.6 Show Playlists Page666.

7、4.6.1 Delete an SPL6 Export an SPL666.4.7 Information Button676.4.8 Licenses Page676.4.9 Delete a License686.5 DEVICE CONTROLLER696.6 DEVICE MANAGER696.6.1 Adding a Projector696.6.2 Removing a Device or Projector716.6.3 Automation Libraries Management726.6.4 Adding an eCNA Device7 Re

8、moving an eCNA Device736.6.5 Adding a JNior Device7 Removing a JNior Device746.6.6 Adding a Raw Device746.6.7 Removing a Raw Device756.6.8 Adding a Serial Device756.6.9 ISE1 Device786.6.10 CSS Device786.6.11 3D Configuration7 Dolby 3D Support7 RealD 3D Support7 Sen

9、sio 3D Support806.6.12 Closed Caption Support806.6.13 Subtitle Engine Configuration806.7 DIAGNOSTIC TOOL826.8 LANGUAGE SETUP836.9 LICENSE MANAGER866.9.1 Adding a License866.10 LIVE MANAGER896.10.1 Creating a Live Event906.10.2 Deleting a Live CPL926.11 LOG MANAGER936.11.1 Log Manager Configuration94

10、6.12 LOG OPERATOR MANAGER956.12.1 Exporting System Logs1006.13 NETWORKING CONFIGURATION104D2K.OM.001822.DRMPage 3 of 177 Doremi LabsVersion 1.46.14 TIME SETTING1046.15 TOUCHSCREEN CALIBRATION1047 INGEST MANAGER GUI1067.1 INGESTING CONTENT1067.2 CONTENT TYPES1067.3 INGESTING CONTENT1087.3.1 Ingesting

11、 content From a USB Drive1087.4 INGESTING CONTENT FROM A REMOTE DOREMI SERVER/LMS1097.4.1 File Transfer Protocol (FTP)10 Ingesting Content From a Doremi Remote Server/LMS1097.5 INGEST PROGRESS1107.6 PNGEST1117.6.1 How to Pngest a CPL1118 SHOW MANAGEMENT USING CINELISTER1138.1 CINELISTER EDIT

12、OR TAB1139 SHOW PLAYLISTS1159.1 AUDIO-VISUAL CONTENT1159.2 SHOW PLAYLIST CREATION1179.2.1 How to Create a New Show Playlist1179.2.2 Element Re-Ordering1 Refresh Button1 Save Button1189.3 EXPORT SHOW PLAYLIST1199.3.1 How to Save and Export a Show Playlist1199.4 IMPORTING A SHOW PLAY

13、LIST1209.4.1 How to Import an SPL12010 ELEMENT PROPERTIES12110.1 UNENCRYPTED CPL'S12210.2 ENCRYPTED CPL WITH KDM VALID (MORE THAN 48 HOURS)12310.3 ENCRYPTED CPL WITH KDM VALID (LESS THAN 48 HOURS)12410.4 DELETING A CPL FROM THE SERVER12511 PLAY 2D CONTENT IN 3D MODE12611.1 3D MODE CONFIGURATION1

14、2611.1.1 How to Set the Show Playlist Mode to 3D12612 ACCESSING A SHOW PLAYLIST12812.1 EDITING AN EXISTING SHOW PLAYLIST12912.2 DELETING A SHOW PLAYLIST13013 AUTOMATION CUES13113.1 MACRO AUTOMATION CUES13113.2 MACRO CREATION USING MACRO EDITOR13113.3 EDITING A MACRO AUTOMATION CUE13313.4 INSERTING A

15、CTIONS INTO MACRO CUES13413.4.1 Add a GPO Action to the Macro Automation Cue13613.4.2 Playback Action Insertion13713.4.3Output Action Insertion138D2K.OM.001822.DRMPage 4 of 177 Doremi LabsVersion 1.413.4.4 Dowser Action Insertion13813.4.5 Projector Channel Switch Insertion13913.5 AUTOMATION LIBRARY

16、USAGE14013.5.1 Using Automation Library14013.5.2 Resulting Macro Setting14113.5.3 Action List Management14 Action Re-Ordering14 Action Edition14 Action Removal14213.5.4 Macro Saving14214 TRIGGER CUE TAB14314.1 TRIGGER CUE TAB OVERVIEW14314.2 TRIGGER CUE CREATION14414.2.1 C

17、onnection to an Event14514.2.2 Connection to a Signal Event14614.3 TRIGGER CUE SAVING14714.4 PRE-DEFINED MACRO USAGE14814.5 DEFAULT CUES14814.6 STARTUP SCRIPTS14815 ADD A TRIGGER CUE TO A SHOW PLAYLIST14915.1 ADD A TRIGGER CUE FOR ONE ELEMENT OF THE SHOW PLAYLIST15016 CINELISTER PLAYBACK TAB15116.1

18、PLAYBACK AN EXISTING SPL15116.2 PLAYBACK PROGRESS15316.3 PAUSE MODE15416.4 ADJUSTING THE DEFAULT VALUES15516.5 PLAYBACK OF A LIVE EVENT15716.5.1 How to Add a Live Event CPL15716.5.2 How to Create and Play an SPL Using a Live Event CPL15716.6 PLAYBACK LOCK MODE15916.7 PLAYBACK ALERT MESSAGES16017 CIN

19、ELISTER SCHEDULE TAB16217.1.1 How to Schedule Playback16217.2 SCHEDULE PLAYBACK MESSAGES16417.2.1 Schedule. 16417.2.2 Scheduled Show Did Not Start Error16517.2.3 Show Playlist Removal16517.3 PLAYBACK RECOVERY DUE TO POWER FAILURE16617.3.1 How to Recover Playback16617.4 SHUTTING DOWN DURING PLAYBACK1

20、6718 CONTROL TAB16818.1 DOWNLOAD THE FILE FROM THE FTP16818.2 CONFIGURING THE CONTROL TAB16818.2.1 Configuration Example16918.2.2 Basic Example of controlview.xml File17119 VIRTUAL KEYBOARD173D2K.OM.001822.DRMPage 5 of 177 Doremi LabsVersion 1.419.1 HOW TO ACCESS THE VIRTUAL KEYBOARD17320 TIME ADJUS

21、TMENT17420.1 HOW TO ADJUST THE SYSTEM TIME17421 ACRONYMS17622 DOCUMENT REVISION HISTORY177D2K.OM.001822.DRMPage 6 of 177 Doremi LabsVersion 1.4Software License AgreementThe software license agreement can be found at the following location:Hardware WarrantyThe hardware warranty can be found at the fo

22、llowing location:China Compulsory Certification (CCC)该仅适用于海拔2000 米以下地区该仅适用于非热带地区此为A 级，在生活环境中，该可能会造成无线电干扰。在这种情况下，可能需要用户对其干扰采取切实可行的措施。D2K.OM.001822.DRMPage 7 of 177 Doremi LabsVersion 1.41Introduction1.1PurposeThis manual is intended to guide the user through the use of the DCP-2000 and DCP-2K4. It al

23、so contains information on how to properly use the CineLister application.1.2Software VersionThis manual is for use with software version 2.4.x and higher.1.3Contact InformationIf in need of help or assistance, please contact Doremi Labs Technical Services:USA24/7 Technical Services line: + 1-Techni

24、cal Services: cinemasupportEurope24/7 Technical Services line: + 33 (0) 492-952-847Technical Services Link:JapanTechnical Services line: +Technical Services: supportdoremilabs.co.jpAustralia China India Indonesia Korea Malaysia New Zealand Philippines Singapore Technical Services Thailand: supportas

25、iaD2K.OM.001822.DRMPage 8 of 177 Doremi LabsVersion 1.42OverviewThe DCP-2000 and DCP-2K4 are high quality DCI JPEG-2000 servers capable of playing movie or trailer packages in MXF format at up to 250Mbits/sec. The DCP-2000 and DCP-2K4 also support MPEG2 Interop movies, pre-show, and alternative cont

26、ent playback.2.1Front Panel2.1.1 DCP-2000 Front PanelA DCP-2000 front panel with an LCD screen is shown below:Figure 1: DCP-2000Figure 2: DCP-2000 HDD CageD2K.OM.001822.DRMPage 9 of 177 Doremi LabsVersion DCP-2K4 Front PanelA DCP-2K4 front panel is shown below:Figure 3: DCP-2K4 Front PanelFi

27、gure 4: DCP-2K4 HDD CagePOWER (PWR): The LED lights turn green when the unit is powered on. HDD: Red LED light indicate access to the Hard Disk Drives.The door on the right on both types of units covers the "POWER" switch and the hard disks that make up the RAID5 storage.Each hard disk dri

28、ve has a blue button that allows removal of the drive from the chassis. Be careful not to remove the hard disk drive when the DCP-2000 or DCP-2K4 is running.There is one USB 2.0 connector on the center of the front panel that can accommodate an external hard drive as well as a mouse or keyboard.The

29、left side of the DCP-2000 front panel contains an LCD screen.On the DCP-2000 front panel, the LCD can be turned on or off by pressing on the LCD power button using the stylus attached to the front panel. This button is located behind the stylus (Figure 1).Note: The use of the LCD screen requires tha

30、t the two rear panel VGA connectors are linked using the VGA cable provided with the DCP-2000.D2K.OM.001822.DRMPage 10 of 177 Doremi LabsVersion 1.43CineListerEvery time the user logs out of the CineLister application and then logs back in again, a “Login Authentication” window will appear (Figure 5

31、). The default login name is “doremi” and the Password is “doremi.” However, the administrator may have changed and or added other login usernames and passwords. Please contact the administrator for the password.Figure 5: Login Authentication WindowFigure 6: CineLister Application andListD2K.OM.0018

32、22.DRMPage 11 of 177 Doremi LabsVersion 1.4ButtonThe CineLister application will appear every time the unit is turned on or rebooted. The button is where users can access various applications as well as the Control Panel(Figure 6).Passwords3.1You will be prompted to enter a password for various task

33、s when using the CineLister application. Your administrator determines the level of security.Note: Please contact your administrator for passwords. The following are types of passwords you may be asked for:Admin (Administrator) ManagerRootNote: In Figure 7 the user is asked to verify the username an

34、d password.Figure 7: Password Confirmation WindowNote: The server will prompt you to the type of password that is needed for a certain task. For example, the authentication required in the window below is “ShowManager” privileges, hence the server will automatically prompt you to the “Manager” usern

35、ame. However, you can also select a different username from the drop-down list as shown in Figure 7 above, depending on the level of security that your administrator has provided for you.Figure 8: Password Confirmation Window - Manager UsernameD2K.OM.001822.DRMPage 12 of 177 Doremi LabsVersion 1.44N

36、etwork Configuration4.1Default Network ConfigurationAll servers are shipped with a default IP address of 0 on the Ethernet port (Eth1) and a DHCP assigned dynamic IP address on the Ethernet port (Eth0).4.2Changing the IP AddressTo change the IP address of the server, select Configuratio

37、n and then follow the steps below: System NetworkingA window will appear asking for a password as illustrated below:Figure 9: Password Confirmation WindowFollow the steps according to the "Ethernet Networking Configuration" Wizard.Figure 10: Network ConfigurationPress Enter to confirm the

38、configuration of each page of the "Ethernet Networking Configuration" Wizard. Press "Tab" to select an option.Enter the desired systems hostname and then press Enter (Note: It is a good idea to put the circuit location/screen number in here. For example, “AMC_bir_scr1,” as it wil

39、l be easier to identify when connecting via VNC and in the logs).Enter the desired system domain name and then press Enter. Select Yes to set eth0 and then press Enter.Select No for Removable Device and then press Enter.Select No for automatically configure device with DHCP and then press Enter.D2K.

40、OM.001822.DRMPage 13 of 177 Doremi LabsVersion 1.4Enter the desired IP address for eth0 and then press Enter.Enter the desired default gateway or leave empty and then press Enter. Enter the desired subnet mask and then press Enter.Select Yes to configure eth1 and then press Enter. Select No for Remo

41、vable device and then press Enter.Select No for automatically configure device with DHCP and then press Enter.Enter the IP address of eth1 and select OK in the example, enter 0 and then press Enter.Note: Do not put leading zeros (0) in front of any numbers. For example, do not input 019

42、0.Enter the desired default gateway or leave empty and then press Enter.Enter the desired subnet mask and select OK in our example, enter the same subnet mask as the projector: and then press Enter.Enter the IP Address of the System's Domain Name Server (or leave empty)

43、and then press Enter to exit the wizard.To verify the setup, go to Doremi Apps. Diagnostic Tool and verify the IPAddress under the Diagnostic Tool System Tab.4.3Network RestartIf for any reason the network needs to be restarted, use the terminal command line below:Type:/etc/init.d/networkingrestart&

44、lt;Enter>D2K.OM.001822.DRMPage 14 of 177 Doremi LabsVersion 1.45Time Zone ConfigurationUnits are by default set to Pacific Time Zone (PST or PDT). This section provides information on how to check and/or change the time zone.5.1Checking the Time ZoneTo confirm that the time zone of the unit is se

45、t correctly, open a terminal window by going tothe “ System Terminal”.Type: date and then press Enter.The current date, time, and time zone will be displayed (Figure 11).Figure 11: Terminal Window with Date DisplayedD2K.OM.001822.DRMPage 15 of 177 Doremi LabsVersion 1.45.2Changing the Time ZoneTo ch

46、ange the time zone, follow the steps below in the terminal window(/System/Terminal):Type: su and then press Enter.Type the "root" password to log in as "root" consult the system administrator to receive the root password or Doremi to know the default root password.Type: rwdo tzco

47、nfig and then press Enter. Type: Yes (to confirm the change).Select the number of the geographic area for the time change (Figure 12).Figure 12: Terminal Window with Time Zone WizardOnce the geographic area number has been selected, press Enter.Type the name of the city / region that you would like

48、the time zone set to (e.g., Singapore, Caribbean, PST, etc.).Press Enter.After typing the city / region, the unit will now be set to the desired configuration.Exit the terminal window.D2K.OM.001822.DRMPage 16 of 177 Doremi LabsVersion 1.46Control PanelTo access the Control Panel window, go toThe fol

49、lowing window will appear:and click on Control Panel.Figure 13: Control Panel WindowThe Control Panel window provides access to various applications as listed below: See Figure 13 above for more information.1.2.Account Manager: Allows the user to add/remove/edit user accounts.Audio Configuration: Al

50、lows the user to route all audio tracks to operator-designated outputs (only SMPTE content).3.4.Content Feed Manager: Allows the user to add an FTP ingest server.Content Manager: Allows the user to browse, manage and export all the content available on the player including: ShowPlaylists, CPLs, KDMs

51、 and Doremi Licenses.Device Controller: Allows the user to create/edit/register devices in a simplified manner.Device Manager: Allows the user to add different projectors, close caption devices, subtitle devices, etc.Diagnostic Tool: Provides the user with Diagnostic information about the system. Se

52、e document “Diagnostic Tool User Guide.”Language Setup window: Allows the user to change the language used on the unit. License Manager: Displays and manages software licenses installed on the unit..9.10. Live Manager: Allows the user to create a device as source of live events.11. Log Manage

53、r: Allows the user to automatically configure SMPTE and System logs.12. Log Operator Maintenance: Allows the user to log important information (e.g., hard disk replacement, projector lamp replacement, etc.). This application helps the system administrator keep track of any change operated in a theat

54、er booth.D2K.OM.001822.DRMPage 17 of 177 Doremi LabsVersion 1.413. Network Configuration: Set up and modify network connections.14. Time Setting: Due to DCI requirements, users can only set the time to no more than 30 minutes per calendar year on a Dolphin DCI FIPS 1.0 board. For Dolphin DCI FIPS 1.

55、2 boards, you can only adjust the RTC (Real Time Clock) time within DCI allowed-time of 6 minutes per calendar year.15. Touch Screen Calibration: Initiates the touch screen calibration process (only applicable toms with a touchscreen).6.1Account Manager GUITo access the Account Manager GUI, double-click on the Account Manager icon within the Control Panel window or select it and click the Start” button located on the right-bottom side of the Control Panel wi