


版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、Preface感您使用燃烧控制研究院生产的就地点火控制柜装置。 本公司的就地点火控制柜装置是燃烧控制研究院自主开发生产的高品质就 地控制装置,在使用系列本程控装置之前请您仔细阅读该手册以保证正确使用并 充分发挥其优越性。本说明书对就地控制柜(以下简称控制柜)的操作和安装方法等做了详细的 介绍。使用控制柜以前,在阅读本说明书的基础上,进行安全正确使用。 Thank you for choosing the Local Ignition Control Cabinet designed by our company.The local ignition control device is expl
2、ored by our company for the ignition control of boiler.This manual describes installation and operation of the cabinet clearly, pleaseread this manual before using.容介绍 Brief introduction本手册介绍了点火控制柜的组成、安装、配线、功能参数、日常使用维护及 对故障的处理The manual includes the cabinet 's components, installation, wiring, d
3、ata,maintenance, and troubleshooting.读者对象 Applicable readers本书适合下列人员阅读 This manual is applicable for 设备安装人员、维护人员、设计人员 Installer, maintenance man, and designer 本书约定 Stipulation符号约定 Symbol stipulations说明提醒操作者需重点关注的地方Points operator should pay attention to由于没有按要求操作可能造成死亡或重伤的场合危险 !This symbol indicates
4、death or GBH that may occur as a resultof improper operation 由于没有按要求操作可能造成中等程度伤害或轻伤或造成物质损害的场 合注意!This symbol indicates secondary injury, flesh wound or object damage that may occur as a result of improper operation一、 序言 Prologue1.1 开箱检查 Checking 在开箱时请认真确认在运输中是否有破损现象 控制柜元器件与附图中的型号数量是否相符 如发现有某种遗漏请速与供货
5、商或我司联系解决! Check if there is any damage.Ensure the model and quantity in chart are accordance with components in cabinet.If there is any mistake, please contact with supplier or our company.1.2 安全注意事项 Security 不要安装在含有爆炸气体的环境里否则有引发爆炸的危险! 必须由具有专业资格的人员进行配线作业否则有触电的危险! 确认电源处于完全断开的情况下才能进行配线作业否则有触电危 险!必须将控制
6、柜的接地端子可靠接地否则有触电的危险! 通电情况下不要用手触摸控制端子否则有触电的危险!Do not install in explosive environment, or it may cause explosion.Do invite professionals for accompany when wiring, or it may cause electric shockDo shut off power before wiring.Do earth the cabinet ground terminal.Do not touch the control terminal when
7、power is on.1.3 安装条件 Installation Requirement环境温度Temperature工作温度 Working temperature : -10 ° C +45 ° C存储温度 Storage temperature : -20 ° C +65 ° C环境湿度Humidity10% 95% (不结露 No Dew )大气环境Atmosphere必须避免下列情况:Avoid the followi ng in sta nee:腐蚀性气体Corrosive gas灰尘、盐份、铁粉集中之处 Dust, salt, or ir
8、on powder水、油,其他化学品飞溅之处Splash range of water, oil, or other chemicals振动和冲击Vibrati on andImpact不能受到直接冲击和振动Avoid direct vibrati on or impact接地 Earthing柜体应固定在平台上,保持良好的接地Place on flat plate, and keep well earthi ng1.4 日常维护 Maintenance定期检查柜各种元器件,确认任一单元都没有松动的螺钉,所有电源和 电线的连接都安全可靠;并保持外观完好。定期吹扫柜,清除积下的灰尘、杂物,保持柜
9、卫生。定期检查控制柜保险丝、继电器和其他可更换元件Check parts in cab in et, faste n bolts and wires connection regularly. Purge the cabinet and keep it 'San.Check fuse, relay and other replaceable in strume nt in cab inet regularly.二、 安装及接线 Installation and Wiring2.1 控制箱的安装方法 Installation of Cabinet Body(柜与柜外接线请查阅共同提交的接
10、线图纸)(Please read wiri ng diagram of inner and outer cab inet connection for refere nee)控制柜顶部有吊耳,用于吊装。吊装时应注意不得将柜体(特别是转角 边缘)上的烤漆磨损或有划伤。柜体应水平放置并紧固在底座上。在技术图纸中,控制柜有专门的接线图,要掌握控制柜原理以及在现场 完成外部接线,都要仔细查阅相关接线图。接线图上的每一根线都有唯一的线号,没有重复。 柜元件与柜外设备发生联系时,都通过接线端子排转接。在接线图上, 端子排横放,其上侧为柜接线,下侧为柜外接线。在端子排两侧的线上除了线 号之外还标有去向(即接
11、至哪一个柜元件或柜外设备) ,并注有文字说明。控制柜在底部预留有进线孔,在接外部电缆时,应将电缆从柜底接入, 并作标识。在全部接线完成并经调试投入运行后,应在柜底将接进电缆用防火 泥封堵。Lug on top of cabinet is for ceil mounting. Do not break or scratch the cabinet paint (especially that on corner) Place and fasten the cabinet on the base.For principle comprehending or outer wiring, please
12、 read the wiring diagram. Each wire in wiring drawing is marked with unique code.Insert the cable through wire inlet at cabinet bottom, and mark it. After the accomplishment of wiring, seal the cable with fire clay .2.2 调试 Regulation在安装接线完成后, 施工人员和调试人员应分别检查接线, 若有错误须及 时改正。检查完毕,可将电源接入, 观察相应指示灯显示是否正确。
13、例如外部设备 的位置状态与指示灯显示的是否一致。如系统带电后工作正常,就可以通过操 作面板进行试运行。调试方法是模拟实际操作,将实际运行所要进行的操作逐 一试验,并观察相应的现象,判断与设计原理是否一致。可能某些条件不具备 而不能进行全部操作, 此时可以做仿真信号, 即在端子排上相应的输入点短接。 DO check each wire, and ensure there is no error after wiring, then turn on power. Turn off each switch one by one from the chief switch, and check th
14、e correctness of indicator light, eg, if working state of outer equipment and light indication are accordance. Cut off power and refer to drawing for cause if there is any mistake. Reset power meter if necessary.Make sure the system is running in order, then single step drive or stop boiler equipme
15、nts and in spect their work ing state.After single step, change to remote control and run it through DCS or operati on pan el. The adjusti ng is to simulate real operati on step by step, and in spect each work ing state.(在这样做之前,一定要仔细查阅相关图纸与说明书,要准确无误)Please read manual and draw ings before regulati o
16、n(在相关模拟试验做完后,一定要将所有的仿真解除)Remove simulate sig nals after the test2.3 使用与操作 Usage and operation必须经过成功调试后,控制柜方可投入使用。操作人员须是经过专门培训的技术人员。在控制柜运行时,不要带电插拔电气元件(继电器等),以免损坏电气设 备或造成不可预知的事故。关闭系统时,从总电源开始逐一断开电源开关。The cab inet could be employed only after adjusti ng.Operator should be professi on al.Do not pull out
17、any electric component with power on, relay for example, or it may lead to un predictable accide nt.Switch off the power from chief power on by one for system closi ng.(系统正在执行监控任务时不得断开电源DO NOT Cutoff powersupply whe n the system is mon itori ng )2.4 故障分析与排除 Troubles and Troubleshooting以下是系统运行时常见故障及排
18、除方法:故障 Troubles原因分析Cause排除方法 Troubleshootinga)输出继 电器不动 作1. 柜电源消失Inner power off2. 操作按钮至继电器的1. 恢复电源Turn on power2. 检查线路,拧紧接线端Outputs线路不通Button to子螺丝 Check circuitrelay offrelay does not workand faste n screw3.继电器损坏3.更换继电器Relay broke nChange relayb)指示灯1.现场设备位置反馈开关1.更换位置反馈开关(行未能真(行程开关)损坏程开关)Change实反映Br
19、oken of equipmentfeedback con trol状态输feedback con trol2.检查线路,拧紧接线端入2.现场设备至控制柜线路子螺丝 Check circuitWrong不通 Circuit obstructedand faste n screwin dicati on3.柜电源消失3.恢复电源Turn onof in dicatorInner power offpowerlight4.指示灯损坏4.更换指示灯ChangeIn dicator light broke nin dicator lightc)气动推1.现场设备至控制柜线路1.检查线路,拧紧接线端进器
20、不不通子螺丝动作Circuit obstructedCheck circuit and fastenPn eumaticscrewActuator2.推进器机械运动不灵活2.查找引起推进器卡住OffActuator Blocked的原因3.限位开关故障Find the causeLimited Switch does not3.更换限位开关或调整workReplace the switch2.5运输与贮存Storage本控制柜可装在单独的木板箱中运输,柜体须保持直立,柜体四周要用泡 沫塑料板与箱壁隔开。箱体上应在合适位置标明“向上,防水,吊装位置”等 的图标。控制柜也可以用特制的大塑料袋罩上,
21、外部用粗草绳垫以厚纸板绑扎。在包装前应将柜各电子设备安装牢固,必要时可以用电缆或草绳将设备绑 扎在柜花梁上。Deliver the cab inet in separate woode n case and fill the gap betwee n cab inet and case with foam. Mark on the case with Upward, Water-proof, and suspended. The cabinet could also be covered with specified plastic sack faste ned and protected w
22、ith cardboard and ropes.Fasten all facilities before packing, and fix the facilities with cable or ropes to the girder in cab inet if n ecessary.三、控制功能及操作 Fun cti on and operatio n3.1 概述 Overview本控制柜适用于锅炉就地点火设备的就地操作及远方控制。The cabinet is applicable for the local and remote control of boiler local igni
23、tion equipments3.2 控制对象 Objectives本控制柜的控制组成对象如下 As following : 点火枪推进装置(气动单电控方式, 220VAC )Spark Rod Actuator (pneumatic single electric control, 220VAC) 油角阀(气动方式, 220VAC )Oil Angle Valve (pneumatic, 220VAC)吹扫阀(气动方式, 220VAC )Purge Valve (Pneumatic, 220VAC) 雾化阀(气动方式, 220VAC )Atomizing Valve (Pneumatic,
24、220VAC)点火器 Ignitor3.3 功能 Function实现对就地点火系统各设备( 3.2 控制对象的容)的现场手动单步控制 和远方程序控制;Local manual single step control and remote control of all local ignition equipments (in item 3.2)显示各设备( 3.2 控制对象的容)的运行状态 ,如“点火枪进到位”等; Working status of all equipments (in item 3.2), eg. Spark rod advanced. 具有集控室就地单步与远方程控的切换
25、,实现就地与程控方式的切换; local/remote control switch具有远操接口,可以接受 DCS 的 2 秒短脉冲无源干接点控制指令 ,并完 成相应的设备联锁动作 ;Remote control interface is available for the 2s pulse passive dry contact point from DCS, and interlock action向 DCS 反馈火检及各设备的当前工作状态,信号采用无源干接点形式 . Feedback status of flame scanner and other equipments to DCS
26、with passive dry contact point signal.3.4 控制柜的操作步骤 Operate Steps of Cabinet操作前请确认或检查 Confirm or examine before operation :? 柜有无杂物、线头,柜是否潮湿,元器件是否有松动、损坏,绝 缘状况如何等等。? 确保控制柜与控制设备的所有连接线全部正确无误。? 确保就地设备处于良好状态,包括动作、绝缘、通断等等。? 通电检查:合上电源开关,查看各就地设备对应的状态指示灯指 示是否正确,若不正确,应断电检查。? Inner cabinet is clean and dry. All
27、components are firm and insulated? All wires are correctly connected? All equipments for local control are in good condition.? Electrifying. Turnon the switch and see if all indicator light are correctly indicated. If there is any error, cutoff power supply and check.请参照设计图纸进行设备的如下操作。 Operate as fol
28、lowing with drawing reference.在具备点火条件之后 ,请确认所有总阀门已经处于关闭状态 .合上柜所有断路 器开关,将面板上 “电源开关”旋转 90 度,此时 “就地指示”( 面板代号 H201 , 绿色)或者“程控指示” ( 面板代号 H202 ,红色)指示灯点亮。Close all the valves, and close all the breakers. Turn 90 °of the power switch, then the local control indicator light (H201, green) or remote contr
29、ol indicator light (H202, red) is on.在集控室发出“点火允许信号” ,点火允许指示灯亮,才能进行就地 /远方操 作。The ignition indicator will be turned on when receivingignition allowed signalfrom control room, and then the local/remote operate is available.将“就地 /程控转换开关”打在就地状态时,就地指示灯亮,表示可以进行 就地单步操作:When the cabinet is under local contro
30、l, the local control indicator light is on, and the local single step operation is available.请按下述步骤进行点火 Ignition steps : 按下“进点火枪” 按钮,将点火枪推进到点火位置, “点火枪进到位” 按钮点亮;按下“开吹扫阀”按钮打开吹扫阀,此时“吹扫阀开到位”点亮,吹扫 计时 15 秒后,按下“关吹扫阀” 按钮关闭吹扫阀, 此时“吹扫阀关到位” 点亮; 按下开“启动点火器” 按钮,启动高能点火器灯点亮, 同时按下“开油角阀” 按 钮和“雾化阀”按钮,打开油角阀和雾化阀,此时“油角阀开
31、到位”点亮, “雾 化阀”开到位点亮,按下“退点火枪” 按钮将点火枪退到原始位置, “点火枪退 到位”点亮;若点火失败,此时应立即按下“关油角阀” 按钮关闭油角阀,待 “油角阀关到位”后,检查点火失败原因。Press advance spark rod button, and advance the spark rod to proper ignition position, then the spark rod advanced indicator light is on. Press open purge valve button, then the purge valve open li
32、ght is on. 15s later, press close purge valve button, then the purge valve closed light is on. Press start ignitor button, then the HEA exciter indicator light is on. Press open oil angle valve and open atomizing valve buttons, then the oil angle valve open and atomizing valve open indicator lights are turned on. Press retract spark rod button, then the spark rod retracted light is on. If ignition is failed, press close oil angle valve button, when the oil angle valve is closed, check and find the cause.停止顺序 Stop Sequence : 按住“关油角阀”按钮关闭油角阀 ,油角阀关到位指示灯点亮 ,停止结束。Press c
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 音乐史西方古典音乐知识点归纳梳理
- 应急消防考试试题及答案
- 六一公司举行活动方案
- 六一创意舞台活动方案
- 六一布置职场活动方案
- 六一幼儿结婚活动方案
- 六一活动互动策划方案
- 六一活动冷餐活动方案
- 六一活动小龙虾活动方案
- 六一活动美业活动方案
- 老旧住宅屋面防水工程施工方案
- 操作规程储气罐安全操作规程
- 电厂物资管理系统解决方案
- 初一数学(下)难题百道及答案
- 七年级下实数及实数的计算
- 中国古典文献学(全套)
- 《抖音平台商品销售策略研究10000字(论文)》
- 两用物项-最终用户用途证明
- 2023-2024学年贵州省铜仁市小学数学五年级下册期末高分预测题
- 会议记录(空白)
- GB/T 20624.2-2006色漆和清漆快速变形(耐冲击性)试验第2部分:落锤试验(小面积冲头)
评论
0/150
提交评论