04挤出工艺卡

1、额定电压10KV、1KV及以下架空绝缘电缆挤出工艺卡 文件编号：HBDL/EGJ-04-2011A编 制：审 核：批 准：受控状态：受 控 号：实施日期：青 岛 市 胶 州 和 邦 电 缆 厂编 制 说 明1、10KV JKY JKLY JKLY/Q JKLHY JKLY/Q 绝缘采用耐候型黑色高密度聚乙烯绝缘料2、1KV JKV JKLV JKLHV 绝缘采用耐候型黑色聚氯乙烯绝缘料3、1KV JKY JKLY JKLHY绝缘采用耐候型黑色低密度或高密度聚乙烯绝缘料4、10 KV JKYJ JKLYJ JKLYJ/Q JKLHYJ JKLHYJ/Q绝缘采用耐候型黑色温水硅烷交联聚乙烯绝缘料5

2、、1KV JKYJ JKLYJ JKLHYJ绝缘采用耐候型黑色温水硅烷交联聚乙烯绝缘料5、控制温度执行Q/JLC-GJ-07B的规定6、绝缘表面印厂名、型号、电压等连续表识，一个完整的标志的末端于下一个标志的始端之间的距离不超过500mm。7、 绝缘应紧密挤包在导体上。绝缘表面应平整，色泽均匀。8、  绝缘厚度的平均值应不小于标称值，其最薄处厚度应不小于标称值的90%-0.1mm。9、 两芯及以上电缆的绝缘上应有表示识别相序的凸处标志，且容易识别。A相为一根凸脊。B相为二根凸脊。C相为三根凸脊。青岛市胶州和邦电缆厂额定电压10kv架空绝缘电缆挤出工艺卡产品型号JKY、JKLY、JKY

3、J、JKLYJ编制依据 GB/T14049-2008共4页产品名称额定电压10kv架空绝缘电缆第1页序号芯数*截面mm2线芯结构根/直径mm导体直径±0.2mm导体屏蔽厚度mm平均屏蔽外径mm模具尺寸mm 使用设备标称绝缘厚度mm绝缘最薄点mm平均外径上限mm模具尺寸mm使用设备标称最大最小标称上限模芯+0.5模套+0.5标称上限模芯+0.5模套+0.1107/1.353.80.550.60.54.95.24.05.1SJ-65挤出机3.42.9611.713.45.112.0SJ-65挤出机2167/1.704.80.550.60.55.96.25.06.1SJ-65挤出

4、机3.42.9612.714.46.113.0SJ-65挤出机3257/2.146.00.550.60.57.17.46.27.33.42.9613.915.67.314.2SJ-90挤出机4357/2.527.00.550.60.58.18.47.59.03.42.9614.916.68.315.555010/2.548.30.550.60.59.49.78.69.6SJ-90挤出机3.42.9616.217.99.617.165019/1.858.30.550.60.59.49.78.69.6SJ-90挤出机3.42.9616.217.99.617.177014/2.5410.00.550

5、.60.511.111.410.211.53.42.9617.919.611.318.387019/2.2010.00.550.60.511.111.410.211.53.42.9617.919.611.318.399519/2.5411.60.650.70.612.913.211.913.23.42.9619.721.413.220.51012024/2.5413.00.650.70.614.314.613.514.63.42.9621.122.814.621.51112037/2.0313.00.650.70.614.314.613.514.63.42.9621.122.814.621.5

6、1215030/2.5414.60.650.70.615.916.215.016.23.42.9622.724.416.222.81315037/2.2814.60.650.70.615.916.215.016.23.42.9622.724.416.222.81418537/2.5416.20.650.70.617.517.816.518.03.42.9624.326.017.824.7SJ-150挤出机1524037/2.8718.40.650.70.619.72018.720.03.42.9626.528.220.026.91630037/3.2120.60.650.70.621.922.

7、220.922.23.42.9628.730.422.229.1注：模具为挤压式青岛市胶州和邦电缆厂额定电压1kv及以下架空绝缘电缆挤出工艺卡产品型号JKY、JKLY、JKV、JKLV、JKLHYJKYJ、JKLYJ 、JKLHYJ 、JKLHV编制依据GB/T12527-2008共4页产品名称额定电压0.6/1kv架空绝缘电缆第2页序号芯数*截面mm2线芯结构根/直径mm导体直径±0.2mm标称绝缘厚度mm绝缘最薄点mm平均外径上限mm模具尺寸mm使用设备标称上限模芯+0.50模套+0.501107/1.353.81.00.85.806.56.010.5SJ-65挤出机2167/1

8、.704.81.20.987.208.07.011.53257/2.146.01.20.988.409.48.013.04357/2.527.01.41.169.8011.09.015.055010/2.548.31.41.1611.2012.310.516.5SJ-90挤出机65019/1.858.31.41.1611.2012.310.516.5SJ-90挤出机77014/2.5410.01.41.1612.8014.112.018.587019/2.2010.01.41.1612.8014.112.018.599519/2.5411.61.61.3414.8016.514.021.510

9、12024/2.5413.01.61.3416.2018.115.522.51112037/2.0313.01.61.3416.2018.115.522.51215030/2.5414.61.81.5218.2020.217.024.51315037/2.2814.61.81.5218.2020.217.024.51418537/2.5416.22.01.7020.2022.518.527.01124037/2.8718.42.21.8822.8025.621.030.0注：模具为挤管式青岛市胶州和邦电缆厂额定电压10kv架空绝缘电缆挤出工艺卡产品型号JKY、JKLY、JKYJ、JKLYJ J

10、KLHY JKLHYJ编制依据 GB/T14049-2008共4页产品名称额定电压10kv架空绝缘电缆第3页序号芯数*截面mm2线芯结构根/直径mm导体直径±0.2mm导体屏蔽厚度mm平均屏蔽外径mm模具尺寸mm 使用设备标称绝缘厚度mm绝缘最薄点mm平均外径上限mm模具尺寸mm使用设备标称最大最小标称上限模芯+0.5 0模套+0.5 0标称上限模芯+0.5 0模套+0.5 01107/1.353.80.550.60.54.95.24.58.0SJ-65挤出机3.42.9611.713.4 6.519.0SJ-90挤出机2167/1.704.80.550.60.55.96.

11、26.510.05SJ-65挤出机3.42.9612.714.4 7.520.0SJ-90挤出机3257/2.146.00.550.60.57.17.47.511.053.42.9613.915.6 9.021.5SJ-90挤出机4357/2.527.00.550.60.58.18.48.512.053.42.9614.916.6 10.022.555010/2.548.30.550.60.59.49.710.014.05SJ-90挤出机3.42.9616.217.9 11.524.065019/1.858.30.550.60.59.49.710.014.05SJ-90挤出机3.42.9616

12、.217.9 11.524.077014/2.5410.00.550.60.511.111.412.016.053.42.9617.919.6 13.025.587019/2.2010.00.550.60.511.111.412.016.053.42.9617.919.6 13.025.599519/2.5411.60.650.70.612.913.213.518.553.42.9619.721.4 14.527.01012024/2.5413.00.650.70.614.314.615.020.03.42.9621.122.8 16.028.51112037/2.0313.00.650.70

13、.614.314.615.020.03.42.9621.122.8 16.028.51215030/2.5414.60.650.70.615.916.216.521.053.42.9622.724.4 17.530.11315037/2.2814.60.650.70.615.916.216.521.053.42.9622.724.4 17.530.11418537/2.5416.20.650.70.617.517.818.023.053.42.9624.326.0 19.532.0SJ-150挤出机1524037/2.8718.40.650.70.619.72020.525.553.42.96

14、26.528.2 21.534.01630037/3.2120.60.650.70.621.922.222.527.553.42.9628.730.4 24.036.5注：模具为挤管式青岛市胶州和邦电缆厂额定电压10kv架空绝缘电缆挤出工艺卡产品型号JKLY/Q JKLHY/Q JKLYJ/Q JKLHYJ/Q编制依据GB/T14049-2008共4页产品名称额定电压10kv架空绝缘电缆第4页序号芯数*截面mm2线芯结构根/直径mm导体直径±0.2mm标称绝缘厚度mm绝缘最薄点mm平均外径上限mm模具尺寸mm使用设备标称上限模芯+0.50模套+0.501257/2.146.02.52

15、.1511.012.28.017.9SJ-90挤出机2357/2.527.02.52.1512.013.29.018.935010/2.548.32.52.1513.314.510.520.4SJ-90挤出机45019/1.858.32.52.1513.314.510.520.4SJ-90挤出机57014/2.5410.02.52.1515.016.212.021.967019/2.2010.02.52.1515.016.212.021.979519/2.5411.62.52.1516.617.814.024.0812024/2.5413.02.52.1518.019.215.525.591203