迅达电梯5400变频器-K 604165

1、 This Manual is the property of INVENTIO AG and shall only be used by SCHINDLER personnel or authorized SCHINDLER agents for purposes which are in the interest of SCHINDLER. This design and information is our intellectual property. Without written consent, it must neither be copied in any manner, no

2、r used for manufacturing, nor communicated to third parties. Application for such consent should be addressed to: INVENTIO AG, Postfach, CH-6052 Hergiswil NWModification 0203Prepared 16.08.04plattle KA No.160069160158Reviewed 17.08.04huwylermi KA Date14.11.0320.08.04Proofreader 18.08.04sturzeiv Rele

3、ased20.08.04micheldo FormatA4INVENTIO AG CH-6052 Hergiswil Classification Lead OfficeE11210 EB4604165K Variodyn VF11BR/VF22BR/VF33BR (VECSYS/VARIOSYSMAINTENANCESummaryThis document contains maintenance instructions for the Variodyn VF22BR/VF33BR (VECSYS and Variodyn VF11BR/VF22BR/VF33BR (VARIOSYS fr

4、equency converters.Variodyn VF22BR/VF33BR VECSYS Variodyn VF22BR/VF33BR VARIOSYSVariodyn VF11BR VARIOSYS Table of Contents1Safety Advice (31.1General (31.2Symbols Used (31.3Product Specific Safety (42Preventive Maintenance (52.1Overview (52.2Prerequisite (52.3Preparation (62.4Check and Adjustment (6

5、3Replacement (73.1Variodyn VF11BR (73.2Variodyn VF22BR/VF33BR (10A.1Parts List (12 1Safety Advice 1.1GeneralSafety Requirements All persons involved must know and follow all company and local safety regulations, with special attention to the following:Make sure that there is enough light to work saf

6、ely.Immediately replace damaged or lost safety equipment.Keep all tools in good condition.Follow instructions when using tools.In addition to protective clothing, the following safety equipment must be used:1.2 Symbols UsedDescription Safety EquipmentSafety ShoesHardhatSafety GogglesFull Body Safety

7、 HarnessProtective GlovesDangerThis symbol indicates a high risk of serious injury. Follow instructions to prevent serious injury or even death.CautionThis symbol indicates a risk of personal injury or property damage. Follow instructions to prevent injury or property damage.NoteThis symbol indicate

8、s special or additional information. 1.3Product Specific Safety DangerBefore any electrical work is performed, the mains must be turned off and locked out following correct safety procedures. 2Preventive Maintenance2.1OverviewTaskTask2.2PrerequisiteSpecial ToolsNo special tools are needed for machin

9、e room installations. SchindlerEuroLift ® machine room less installations need the following tool. Special ToolsInterval (MonthsDescriptionTime (MinutesDetails given in 24Check operation of the fans.5Section 2-3ToolImageDescriptionCarMaintenance PlatformAll maintenance work on the frequency con

10、verter is done from inside the car using the maintenance platform integrated into the car roof. Maintenance Documentation No additional documentation is needed for preventive maintenance. See "Replacement" for details.2.3PreparationProcedure Every visit check the following and attend to or

11、 report any problems to the servicedepartmentPut signs "Out of Service" in front of each landing door,Check that during maintenance work the car is neither occupied by persons nor goods,Switch on hoistway lights,Check for any roll back or out of level conditions,Record the number of trips

12、per the trip counter in the installation record book.2.4Check and Adjustment Ventilator Check Document DescriptionK 604439Variodyn VF11BR/VF22BR/VF33BR (VARIOSYS TABA/DispoK 604162Variodyn VF11BR/VF22BR/VF33BR (VARIOSYS InstallationJ 41400465Parameter DescriptionJ 41400575Return of a Defective Power

13、 ConverterK 604442Diagnostics Variodyn VF22BR/VF33BR/VF44BR (VARIOSYSK 604163Commissioning VF22BR/VF33BR for PMS/PMA Motors with Miconic MX-GC(without SMLCD Version 2 and aboveK 604441Commissioning VF22BR/VF33BR/VF44BR (VarioSys for PMS/PMA/SM250Synchronous Motors with Miconic MX-GC (SMLCDK 604450Co

14、mmissioning VF22BR/VF33BR (VarioSys or VF30BR/VF50BR/VF85BR(VecSys for Asynchronous Motors with Miconic MX-GC (SMLCDNo Step1Check that all ventilators are operating.2If any one of the ventilators is not operating, the entire frequency converter mustbe replaced. See "Replacement" for instru

15、ctions. 3Replacement 3.1Variodyn VF11BRDisassemblyProcedure Remove Protection Roof1Converter2M4x6 Screw3Protection Roof DangerBefore any electrical work is performed, the mains must be turned off and locked out following correct safety procedures.CautionThe VF11BR/VF22BR/VF33BR converter weighs 12/2

16、2.5/26 kg, not including the support bracket. Two installers are needed to lift and position the converter.NoteOnly the entire frequency converter can be replaced. The frequency converter must not be opened by maintenance personnel.No Step1Remove all electrical connections.2Unscrew four screws (2 to

17、 remove the protection roof (3 from the converter (2.123 Remove Converter4RIP Washers5M6 Hex NutsAssembly Procedure SchindlerEuroLift Commissioning 3Unscrew the nuts (5 and washers (4 and remove the converter (1.210_000083a_02451NoteIf the converter has already been commissioned, make sure that the

18、converter is status "Not Commissioned" so that new parameters can be downloaded.MX-GC Release 3, P150 0MX-GC Release 4, P150 0 (Available with MX-GC software V2.43. If MX-GC software < V2.43, see K 604442 Diagnostics Variodyn VF22BR/VF33BR/VF44BR (VARIOSYS, "VarioCon PCB, Diagnosis

19、 via LED".4Install the new frequency converter in the reverse order.See K 604162 Installation Variodyn VF11BR/VF22BR/VF33BR VECSYS/VARIOSYS for details.5Commission the new frequency converter according to the correctcommissioning instruction.Component Document SMLCD PMS/PMA Motor Asynchronous M

20、otorK 604163_2No Yes NoK 604441Yes Yes NoK 604450Yes No Yes Shipping Box on Pallet Waste Disposal Caution The converter is fragile electrical equipment. It must be protected during shipping. The shipping container must be strong enough to protect the converter and must be well padded. Make sure to u

21、se appropriate warning labels to ensure proper handling.When using the original cardboard shipping box, additional padding can be made by tying the box to a pallet, as shown below.Do not ship converter components in the original cardboard box without additional padding!6Fill out the form J 41400575

22、Return of a Defective Power Converter.7Return the defective converter to the supplier. 3.2Variodyn VF22BR/VF33BR DisassemblyProcedureRemove Frequency Converter AssemblyProcedure NoteOnly the entire frequency converter can be replaced. The frequency converter must not be opened by maintenance personn

23、el.No Step1Remove all electrical connections.2Remove M5 set screw (arrow 1.3Lift (arrow 2 the converter and remove (arrow 3 the converter from thesupporting bracket.4Reuse the supporting bracket for installing the new converter.AA321210_000047a_01NoteIf the converter has already been commissioned, m

24、ake sure that the converter is status "Not Commissioned" so that new parameters can be downloaded.MX-GC Release 3, P150 0MX-GC Release 4, P150 0 (Available with MX-GC software V2.43. If MX-GC software < V2.43, see K 604442 Diagnostics Variodyn VF22BR/VF33BR/VF44BR (VARIOSYS, "Vario

25、Con PCB, Diagnosis via LED".5Install the new frequency converter in the reverse order.See K 604162 Installation Variodyn VF11BR/VF22BR/VF33BR VECSYS/VARIOSYS for details.6Commission the new frequency converter according to the correctcommissioning instruction.Variodyn VF11BR/VF22BR/VF33BR (VECS

26、YS/VARIOSYS Maintenance K 604165 / 03 Component Document SMLCD PMS/PMA Motor Asynchronous Motor K 604163_2 K 604441 K 604450 No Yes Yes Yes Yes No No No Yes SchindlerEuroLift Commissioning Caution The converter is fragile electrical equipment. It must be protected during shipping. The shipping container must be strong enough to protect the converter and must be well padded. Make sure to use appropriate warning labels to ensure proper handling. When using the original cardboard shipping box, additional padding can be made by tying the box to a pallet, as shown below. Do not ship converter c