控机床故障诊断与维修几例

1、控机床故障诊断与维修几例由于现代数控系统的可靠性越来越高，数控系统本身的故障越来越低，而大部分故障的发生则是非系统本身原因引起的。系统外部的故障主要指由于检测开关、液压元件、气动元件、电气执行元件、机械装置等出现问题而引起的。 数控设备的外部故障可以分为软故障和外部硬件损坏引起的硬故障。软故障是指由于操作、调整处理不当引起的，这类故障多发生在设备使用前期或设备使用人员调整时期。对于数控系统来说，另一个易出故障的地方为伺服单元。由于各轴的运动是靠伺服单元控制伺服电机带动滚珠丝杠来实现的。用旋转编码器作速度反馈，用光栅尺作位置反馈。一般易出故障的地方为旋转编码器与伺服单元的驱动模块。也有个别的是由

2、于电源原因而引起的系统混乱。特别是对那些带计算机硬盘保存数据的系统。例如，德国西门子系统840C。 例1：一数控车床刚投入使用的时候，在系统断电后重新启动时，必须要返回到参考点。即当用手动方式将各轴移到非干涉区外后，再使各轴返回参考点。否则，可能发生撞车事故。所以，每天加工完后，最好把机床的轴移到安全位置。此时再操作或断电后就不会出现问题。 外部硬件操作引起的故障是数控修理中的常见故障。一般都是由于检测开关、液压系统、气动系统、电气执行元件、机械装置出现问题引起的。这类故障有些可以通过报警信息查找故障原因。对一般的数控系统来讲都有故障诊断功能或信息报警。维修人员可利用这些信息手段缩小诊断范围。

3、而有些故障虽有报警信息显示，但并不能反映故障的真实原因。这时需根据报警信息和故障现象来分析解决。 例2：我厂一车削单元采用的是SINUMERIK840C系统。机床在工作时突然停机。显示主轴温度报警。经过对比检查，故障出现在温度仪表上，调整外围线路后报警消失。随即更换新仪表后恢复正常。 例3：同样是这台车削中心，工作时CRT显示9160报警“9160 NO PART WITH GRIPPER 1 CLOSED VERIFY V14-5”。这是指未抓起工件报警。但实际上抓工件的机械手已将工件抓起，却显示机械手未抓起工件报警。查阅PLC图，此故障是测量感应开关发出的。经查机械手部位，机械手工作行程不

4、到位，未完全压下感应开关引起的。随后调整机械手的夹紧力，此故障排除。 例4：一台立式加工中心采用FANUC-OM控制系统。机床在自动方式下执行到X轴快速移动时就出现414和410报警。此报警是速度控制OFF和X轴伺服驱动异常。由于此故障出现后能通过重新启动消除，但每执行到X轴快速移动时就报警。经查该伺服电机电源线插头因电弧爬行而引起相间短路，经修整后此故障排除。 例5：操作者操作不当也是引起故障的重要原因。如我厂另一台采用840C系统的数控车床，第一天工作时完全正常，而第二天上班时却无论如何也开不了机，工作方式一转到自动方式下就报警“EMPTYING SELECTED MOOE SELECTO

5、R”。加工完工件后，主轴不停，机械手就去抓取工件，后来仔细检查各部位都无毛病，而是自动工作条件下的一个模式开关位置错了。所以，当有些故障原因不明的报警出现的话，一定要检查各工作方式下的开关位置。 还有些故障不产生故障报警信息，只是动作不能完成，这时就要根据维修经验、机床的工作原理和PLC运行状况来分析判断了。 对于数控机床的修理，重要的是发现问题。特别是数控机床的外部故障。有时诊断过程比较复杂，但一旦发现问题所在，解决起来比较简单。对外部故障诊断应遵从以下两条原则。首先要熟练掌握机床的工作原理和动作顺序。其次，要会利用PLC梯形图。NC系统的状态显示功能或机外编程器监测PLC的运行状态，一般只

6、要遵从以上原则，小心谨慎，一般的数控故障都会及时排除。 森精机使用<Control+F>然后键入报警你正在寻找。 Remember to use the same number format that is displayed on your machine (for example, EX0001, or EX001, or EX01)记住要使用相同的数字格式显示在您的机器（例如，EX0001或EX001，或EX01） EX0013, SPINDLE OR ROTARY TOOL SPINDLE ON, A4.5, An auto door open command has be

7、en given during spindle or rotary tool spindle rotation. EX0013，主轴或旋转刀具主轴ON时，A4.5，自动门打开命令我已经在主轴或旋转刀具主轴旋转。 EX0016, TAILSTOCK IS NOT CLAMPED , A11.0, A cycle start has been activated with the tailstock not clamped. EX0016，尾座的IS不钳位 ，A11.0，一个周期已开始启动尾座夹紧不符合。 EX0018, ALL-AXES NEED ZERO RETURN, A0.0 EX0018

8、，所有轴必要性非零返回，A0.0 A cycle start has been activated without the all-axes zer0-returns after a machine lock cancel.一个周期已开始启动，但无所有轴zer0，机械锁返回后取消。 EX0019, WORK COUNTER AT FULL COUNT, A0.1, A cycle start has been activated with the PC or external work counter at full count. EX0019，工作柜台完整的数，A0.1，一个周期已开始启动计

9、数与PC柜台全部或对外工作。 EX0020, EDITING KEY SWITCH IS ON , A0.2,  A cycle start has been activated with Editing Key Switch on. EX0020，编辑键开关ON时 ，A0.2，一个周期开始一直激活编辑按键开关。 EX0023, START INTERLOCK SIGNAL ON , A0.3, A cycle start has been activated while while an external start interlock signal has been input.

10、 EX0023，裁武联锁信号 ，A0.3，一个周期开始时已被激活，而外部启动联锁信号现已投入。 EX0024, CHUCK IS NOT CLAMPED , A0.4, A cycle start has been activated with the chuck is not clamped. EX0024，查克是不是钳位 ，A0.4，一个周期已开始启动夹头与不夹紧。 EX0026, PLEASE CLOSED THE DOOR , A5.7, A cycle start has been activated without the door closed. EX0026，请关上门 ，A5.

11、7，一个周期开始了门激活没有关闭。 Close the door.关闭的大门。 EX0029, TAILSTOCK QUILL IS NOT OUT , A11.1, A cycle start has been activated during tailstock inching or with the tailstock spindle not OUT. EX0029，尾座主轴是并不过分 ，A11.1，一个周期已开始启动尾座尾座在主轴缓慢或没有出来。 EX0035, CUT OFF INCOMPLETE , A4.1, Cut off has not been completed. EX0

12、035，切断不完整 ，A4.1，切断尚未完成。 EX0068, INTERLOCK RELEASE TIME OVER , A13.0, Door interlock cancel state has been invalid. EX0068，联锁释放时间结束 ，A13.0，门联锁取消国家已无效。 EX0069, DOOR LOCK TIME OVER , A14.0, Door lock complete signal has not been turned ON after elapsing the time set on timer. EX0069，门锁时间比 ，A14.0，门锁完整的信

13、号并没有被打开后，定时器设定的时间流逝。 EX0079, SPINDLE ORT. EX0079，主轴口服补液疗法。 CIRCUIT ABNORMAL , A19.4, Spindle circle orientation detection circuit is abnormal. 电路异常 ，A19.4，主轴循环方向检测电路是不正常的。 Though orientation has been held detection signal is not on.尽管方向已经举行了探测信号不在。 Though orientation has not been held, detection sig

14、nal is not off.虽然方向尚未举行，检测信号，离不开。 EX0089, SPEED DETECTION CIRCUIT IS ABNORMAL , A7.5, Speed dectection signal of monitor circuit is abnormal. EX0089，速度检测电路异常 ，A7.5，速度监测电路检测试剂的信号是不正常的。 Though spindle or rotary tool spindle has not been rotated, speed detection signal is on.虽然主轴或旋转刀具主轴并没有旋转，速度检测信号上。 T

15、hough spindle or rotary tool spindle has been rotating over fixed speed, speed dectection signal is off.虽然主轴或旋转刀具主轴速度已经超过固定旋转，速度检测试剂信号是关闭的。 EX0097, PANEL I/O ALARM , A2.7, An I/O alarm has been occured in the flat type operation panel. EX0097，面板I / O报警 ，A2.7，一个I / O报警已发生的平板式操作面板。 EX0099, PANEL ALARM

16、 , A5.6, An alarm has been occurred in the flat type operation panel. EX0099，面板报警 ，A5.6，报警已发生的平板式操作面板。 EX0302, IMPROPER T-CODE COMMAND ERROR , A6.0, A T-command out of turret station number has been given. EX0302，不当的T代码命令错误 ，A6.0，一个T型指挥人数从炮塔站已发出。 EX0303, TURRET SHORT-PATH INDEX MODE , A0.7, During t

17、urret short-path index mode, turret forward reverse is commanded. EX0303，转塔短路径指数模式 ，A0.7，在炮塔最短路径指数模式，炮塔向前向后是指挥。 EX0320, POLYGON MODE , A15.0, A T-command has been given during polygon mode. EX0320，多边形模式 ，A15.0，一个T型命令我已经在多边形模式。 EX0357, TURRET INDEX TIME OVER , A6.2, Turret indexing has not been compl

18、eted within the specified time. EX0357，转塔指数时间结束 ，原子团，转塔分度尚未完成在指定时间内。 EX0322, TAILSTOCK IS NOT CLAMPED , A11.2, A spindle forward/reverse, rotary tool spindle forward/reverse, rigid tap mode command has been given while the tailstock is not clamped. EX0322，尾座的IS不钳位 ，A11.2，主轴前进/后退，旋转刀具主轴前进/后退，刚性自来水模式命

19、令已被给予，而不是尾座夹紧。 EX0324, TAILSTOCK IS NOT CLAMPED , A11.3, A T-command has been given while the tailstock is not clamped. EX0324，尾座的IS不钳位 ，A11.3，一个T型命令已被给予，而不是尾座夹紧。 EX0333, TAILSTOCK QUILL IS OUT , A10.1, A tailstock clamp/ unclamp command, tailstock forward/ backward command has been given with the t

20、ailstock spindle out or inching state. EX0333，尾座鹅毛笔都出了 ，A10.1，阿尾架夹紧/松开命令，尾座前进/后退命令已被国家给予与尾座主轴出或缓慢。 EX0374, TOOL LIFE ENDING , A7.1, Tool life ending. EX0374，刀具寿命结束 ，A7.1，刀具寿命结束。 EX0380, TAILSTOCK CLAMP/ UNCLAMP TIME OVER , A19.5, The tailstock clamp/unclamp operation has not been completed  wit

21、hin the specified time. EX0380，尾座夹紧/松开时间比 ，A19.5的尾座夹紧/松开操作没有被指定的时间内完成。 EX0381, TAILSTOCK CLAMP SIGNAL OFF , A6.3, The clamp check signal has been deactivated with the tailstock was clamped. EX0381，尾座钳信号关闭 ，A6.3，夹具检查信号已被停用与尾座的钳制。 EX0386, TURRET NEED ZERO RETURN , A0.6, The turret clamp check limit sw

22、itch has been deactivated during cycle start. EX0386，转塔必要性非零返回 ，A0.6，炮塔钳检查限位开关已被停用期间周期的开始。 EX0395, TURRET INPOSITION CHECK ERROR , A8.3, Turret inposition check is turned off for 5 seconds. EX0395，转塔INPOSITION检查错误 ，A8.3，炮塔inposition检查关闭5秒。 EX0401, SPINDLE OR ROTARY TOOL SPINDLE ON, A1.1, Spindle/ ro

23、tary tool spindle reverse command has been given during their forward rotation or spindle/ rotary tool spindle forward command has been given during their reverse rotation. EX0401，主轴或旋转刀具主轴ON时，A1.1，主轴/刀具主轴旋转反向命令我已经在向前旋转或主轴/旋转刀具主轴旋转着命令已被期间给予他们的逆转。 EX0404, S-CODE IS NOT COMMANDED , A1.2, A spindle for

24、ward/ reverse, rotary tool spindle forward/ reverse command has been given either without given an S-code command after turning on the power or after giving an SO command. EX0404，第S -代码是没有吩咐 ，A1.2，主轴前进/后退，旋转刀具主轴前进/后退命令已被命令后没有或给予任何如此发出的权力给予一个一个S -代码命令后打开的。 EX0406, SPINDLE INTERLOCK SIGNAL ON , A1.3,

25、A spindle forward/reverse, spindle orientation, synchronous operation on, rotary tool spindle forward/ reverse, rotary tool spindle orientation, rigid tap mode on command has been given while the external spindle interlock signal activated. EX0406，主轴联锁信号 ，A1.3，主轴前进/后退，主轴定位，同步操作上，旋转刀具主轴前进/后退，旋转刀具主轴的方

26、向，模式命令刚性自来水已获而外部主轴联锁信号激活。 EX0407, SP. EX0407，警司。 /R T. SP. /住宅吨警司。 DIRECTION INCORRECT , A1.4, The direction of spindle or rotary tool spindle rotation has been changed or while shifting the operation mode from automatic to manual, or from manual, to automatic. 方向正确 ，A1.4，旋转方向的主轴或旋转刀具主轴已被更改或在转移从自动操作

27、模式为手动，或从手动，自动。 EX0410, SPINDLE OR ROTARY TOOL SPINDLE ON , A1.5, A chuck open/close command has been given during spindle or or rotary tool spindle rotation. EX0410，主轴或旋转刀具主轴ON时 ，的1.5，一个夹头打开/关闭命令已在或或给予主轴旋转刀具主轴旋转。 EX0411, SPINDLE JOG ON , A1.6, A spindle forward/reverse, spindle orientation, synchron

28、ous operation on command has been given during spindle jogging. EX0411，主轴JOG旋钮ON时 ，A1.6，主轴正向/反向，主轴方向，就命令同步操作已被慢跑期间给予主轴。 EX0412, CHUCK IS NOT CLAMPED , A1.7, A spindle forward/ reverse, rotary tool spindle forward/ reverse, rigid tap mode command has been given with the chuck is not clamped. EX0412，查

29、克是不是钳位 ，A1.7，主轴正向/反向，旋转刀具主轴正向/反向，刚性自来水模式命令已查与不给夹住。 EX0421, TAILSTOCK IS IN INCHING MODE , A10.4, A spindle forward/reverse, rotary tool spindle forward/reverse, rigid tap mode command has been given during tailstock spindle inching. EX0421，尾座的IS模式命令我已经在尾座主轴小幅的微调模式 ，A10.4，主轴前进/后退，旋转刀具主轴前进，/扭转刚性自来水。 E

30、X0428, RT SP. EX0428，逆转录警司。 INTERLOCK SIGNAL ON , A2.0, A rotary tool spindle forward/ reverse, rigid tap mode command has been given while the external rotary tool spindle interlock signal activated. 联锁信号 ，A2.0，一个旋转刀具主轴正向/反向，刚性挖掘模式的命令已发出，而外围旋转刀具主轴联锁信号激活。 EX0429, ROTARY TOOL SPINDLE JOG ON , A2.1, A

31、 rotary tool spindle forward/reverse,  rigid tap mode, rotary tool spindle orientation command has been given during rotary tool spindle jogging. EX0429扶轮对机床主轴JOG旋钮 ，A2.1，一个旋转刀具主轴正向/反向，刚性自来水模式，旋转刀具主轴方向命令已慢跑期间给予旋转刀具主轴。 EX0451, SPINDLE DRIVE UNIT ALARM , A7.3, The spindle drive unit alarm has bee

32、n activated. EX0451，主轴驱动装置的报警器 ，利用A7.3，主轴驱动装置报警已被激活。 EX0457, SPINDLE DRIVE UNIT ALARM #2 , A9.3, The headstock 2 spindle drive unit alarm has been activated. EX0457，主轴驱动装置的报警器2，A9.3，在车头2主轴驱动装置报警已被激活。 EX0461, TAILSTOCK OUT SWITCH IS ABNORMAL , A7.4, The tailstock out check signal has been deactivated

33、 with the tailstock spindle out. EX0461，尾座出门开关不正常 ，A7.4，信号尾座尾座出的支票已被停用的主轴了。 EX0490, SPINDLE  SPEED ABNORMAL , A19.6, Spindle speed abnormality has been detected, Please check the following. EX0490，主轴转速异常 ，A19.6，主轴转速已检测到异常，请检查以下。 Parameter setting is not correct.参数设置不正确的。 Spindle unit is abnorma

34、l.主轴单元是不正常的。 EX0551, ELECTRICAL CABINET OVER HEAT , A3.1, Excess heat in electrical control unit. EX0551，电气柜过热 ，A3.1，过剩热量单位在电气控制。 Check unit and filter.检查单位和过滤器。 EX0560, AIR PRESSURE LOW , A16.2, Air pressure has dropped. EX0560，气压低时 ，A16.2，气压下降。 EX0561, HYDRAULIC PRESSURE LOW , A3.3, Hydraulic pres

35、sure has dropped. EX0561，液压压力低 ，A3.3，油压下降。 EX0562, LUBRICANT PRESSURE LOW , A4.4, Lubrication oil pressure has not increased. EX0562，润滑压力低 ，A4.4，润滑油的压力并没有增加。 Possible cause is broken piping or motor failure.可能的原因是管道破裂或马达故障。 EX0563, LUBRICANT PRESSURE HIGH , A3.5, Lubrication oil has not decreased wi

36、thin the specified time after turning the cycle pump OFF. EX0563，润滑压力高 ，A3.5二零零六年，润滑油并没有减少在指定时间内循环泵转动后关闭。 Possible cause is failure in the pressure switch or the magnet.可能的原因是在压力开关或磁铁失败。 EX0567, LUBRICANT WATCH DOG ALARM , A3.6, Lubrication pump pressure detection switch has not been activated withi

37、n the specified time. EX0567，润滑剂看门狗报警 ，A3.6，润滑泵的压力检测开关未能在指定时间内启动。 EX0570, LUBRICANT OIL LEVEL LOW , A3.7, Insufficient lubricant oil. EX0570，润滑油水平低 ，A3.7，没有足够的润滑油。 Add oil as necessary.新增的石油需要。 (Message) （消息） EX0599, LUBRICANT OIL EMPTY , A10.6, Shortage of lubrication oil. EX0599，润滑油空 ，A10.6，石油短缺的润

38、滑。 Add oil as necessary.新增的石油需要。 (Error) （错误） EX0910, PLEASE CLOSED THE DOOR , A2.2, A parts catcher OUT command has been given while the door is not closed. EX0910，请关上门 ，A2.2，一个输出命令已得到部分捕手，而不是封闭的大门。 EX0913, SPINDLE OR ROTARY TOOL SPINDLE ON , A15.2, A auto presetter arm down command has been given

39、during spindle or rotary tool spindle rotation. EX0913，主轴或旋转刀具主轴ON时 ，A15.2，手臂向下一个命令自动预调我已经在主轴或旋转刀具主轴旋转。 EX0914, TOOL PRESETTER ARM DOWN , A10.3, The parts catcher OUT command has been given while the headstock 2 presetter arm dose not rise. EX0914，刀具预调仪的扶手上 ，A10.3，捕手的部分命令输出已发出，而启闭2预调臂剂量不会上升。 EX0915,

40、 X,  Z-AXIS NEED ZERO RETURN , A15.3, An auto presetter arm down command has been given while X, Z-axis is not at the zero point. EX0915中，x，Z轴必要性零返 ，A15.3，手臂向下一个自动预调命令已发出，而十，Z轴是不是在零点。 EX0916, PARTS CATCHER NOT HOME POSITION , A11.6, Auto presetter arm down, auto door open/close, tailstock uncla

41、mp command has been given while the parts catcher is not in the home position. EX0916，工件捕捉器不在家的地位 ，A11.6，自动预调臂下，自动门打开/关闭，松开尾座已发出命令，而部分捕手是不是在家里的地位。 EX0922, CHUCK IS CLAMPED , A5.0, Bar feeder command has been given during chuck clamped. EX0922，夹头夹紧 ，A5.0，酒吧接驳命令已查期间给予钳制。 EX0923, TOOL PRESETTER SENSOR

42、ON , A15.4, An auto presetter arm rise command has been given while the sensor is ON. EX0923，刀具预调仪传感器 ，A15.4，自动预调臂上升命令已被给予，而传感器是ON。 EX0930, OPTION ALARM 1 , A23.0, Alarm in special design. EX0930，期权报警1，A23.0，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0931, OP

43、TION ALARM 2 , A23.1, Alarm in special design. EX0931，期权报警2，A23.1，设计报警特殊。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0932, OPTION ALARM3 , A23.2, Alarm in special design. EX0932，期权ALARM3，A23.2，设计报警特殊。 Refer to the accompanying documents for the special design.是指为特殊设计的

44、附带文件。 EX0933, OPTION ALARM 4 , A23.3, Alarm in special design. EX0933，期权报警4，A23.3，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0934, OPTION ALARM 5 , A23.4, Alarm in special design. EX0934，期权报警五 ，A23.4，闹钟在特殊设计。 Refer to the accompanying documents for the specia

45、l design.是指为特殊设计的附带文件。 EX0935, OPTION ALARM 6 , A23.5, Alarm in special design. EX0935，期权报警6，A23.5，闹钟在特殊设计。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0936, OPTION ALARM 7 , A23.6, Alarm in special design. EX0936，期权报警7，A23.6，在特殊设计报警。 Refer to the accompanying document

46、s for the special design.是指为特殊设计的附带文件。 EX0937, OPTION ALARM 8 , A23.7, Alarm in special design. EX0937，期权报警8，A23.7，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0945, ROBOT/LOADER COMMAND ERROR , A12.7, ROBOT/LOADER command has been given while the machine is no

47、t in home position. EX0945，机器人/装载机命令错误 ，A12.7，机器人/装载机已发出命令，而机器不在家中的地位。 EX0946, ROBOT/LOADER ARM IN , A11.4, T-code, coolant on, auto presetter arm down, spindle forward/reverse, rotary tool spindle forward/reverse, rotary tool connection check command has been given while robot/loader arm is moving

48、in. EX0946，机器人/装载机动臂中 ，A11.4，T型码，冷却液对，自动预调臂下，主轴前进/后退，旋转刀具主轴前进/后退，旋转刀具的连接查询命令而被赋予机器人/装载机臂入伙 EX0951, TOOL PRESETTER SENSOR ON , A12.0, The sensor has been activated without setting the presetter mode. EX0951，刀具预调仪传感器 ，A12.0，该传感器已启动不设置预调模式。 EX0953, TOOL PRESETTER SENSOR ON , A12.1, The sensor has been

49、activated with the presetter arm rising. EX0953，刀具预调仪传感器 ，A12.1，该传感器已被激活的预调上升手臂。 EX0953, TOOL PRS. EX0953，工具减贫战略。 ARM DOWN IN AUTO MODE , A12.2, The presetter arm rise dectection signal has been deactivated during automatic mode. ARM的信号向下在自动模式下 ，A12.2，增加检测试剂的预调手臂已停用在自动模式。 EX0956, TWO OR MORE SENSORS

50、 ON SAME TIME , A12.3, Two sensors or more have been activated during presetter mode. EX0956，两个或以上的其他传感器在同一时间 ，A12.3，两个传感器被激活时预调模式。 EX0959, BAR FEEDER EMG. EX0959，英美馈线肌电图。 STOP SIGNAL ON , A5.1, Bar feeder is in emergency stop state. 停止信号 ，A5.1，酒吧接驳在紧急停止状态。 EX0962, ROBOT/LOADER CYCLE TIME OVER , A13

51、.3, ROBOT/LOADER cycle has not been completed in the specified time. EX0962，机器人/装载机生产周期结束 ，A13.3，机器人/装载机周期尚未完成，在指定的时间。 EX0964, MATERIAL IN ROBOT/LOADER EMPTY , A12.6, On models equipped with a robot/loader, workpieces have run out. EX0964，材料中的机器人/装载机空 ，A12.6，在车型配备了一个机器人/装载机运行，工件有。 EX0966, ROBOT/LOAD

52、ER ALARM SIGNAL ON , A11.5, The robot/loader alarm has been output. EX0966，机器人/装载机报警信号 ，A11.5，机器人/装载机警报已输出。 EX0968, BAR IN STOCK EMPTY , A5.2, On the mode equipped with one piece bar feeder, bar stock has run out. EX0968，英美在股市空 ，A5.2在酒吧一条支线的模式配备1，酒吧库存已经耗尽。 EX0979, WORK SEATING SIGNAL TIME OVER , A12

53、.5, The chuck clamp  operation has not been completed within the specified time when workpiece holding detection specification. EX0979，工作时间超过座位信号 ，A12.5，夹头夹不规范操作已完成，在规定时间内举行时工件的检测。 EX0980, OPTION ALARM 21 , A24.o, Alarm in special design. EX0980，期权报警21 A24.o，在特殊设计报警。 Refer to the accompanying d

54、ocuments for the special design.是指为特殊设计的附带文件。 EX0981, OPTION ALARM 22 , A24.1, Alarm in special design. EX0981，期权报警22，A24.1，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0982, OPTION ALARM 23 , A24.2, Alarm in special design. EX0982，期权报警23，A24.2，在特殊设计报警。 Refer t

55、o the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0983, OPTION ALARM 24 , A24.3, Alarm in special design. EX0983，股权报警24，A24.3，设计报警特殊。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0984, OPTION ALARM 25 , A24.4, Alarm in special design. EX0984，期权报警25，A24

56、.4，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0985, OPTION ALARM 26 , A24.5, Alarm in special design. EX0985，期权报警26，A24.5，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0986, OPTION ALARM 27 , A24.6, Alarm in special desig

57、n. EX0986，期权报警27 A24.6，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0987, OPTION ALARM 28, A24.7 , Alarm in special design. EX0987，期权报警28 A24.7，在特殊设计报警。 Refer to the accompanying documents for the special design.是指为特殊设计的附带文件。 EX0999, SEQUENCE PROGRAM ABNORMAL ,

58、 A4.2, Abnormality in sequence program. EX0999，顺控程序异常 ，约合35，程序异常的序列。 Contact Mori Seiki.联系森精机制作所。 EX1005, PLEASE SUPPLY THE NEW MATERIAL , A5.3, A cycle start has been activated when the bar stock runs out. EX1005，请提供新材料 ，A5.3，一个周期开始时已被激活时，棒料用完。 Put the new stock.把新的股票。 (one piece bar feeder) （1件送料器

59、） EX1024, PLEASE OPEN THE DOOR ONCE , A14.1, The door has never been opened after executing M02 or M3o command. EX1024，请打开门后 ，A14.1，门被打开后，一直没有执行M02或M3o命令。 Open and close the door before starting new cycle.打开和关闭门，才开始新的周期。 EX1034, POWER MUST BE OFF , A15.1, After turning off the power once, turn it on again. EX1034，电源必须关闭 ，A15.1，关掉电源后一次，再次打开它。 EX1035, LOAD MONITOR PARAMETER E