PV高清一体机机芯技术手册

1、高清一体机机芯技术手册PV- 6110 PV - 6220目录特点：3基本功能：5尺寸图：5规格说明：636Pin FPC 说明：730Pin 同轴线说明：8控制板程序烧录说明：9命令列表：9特殊说明：13特点：优异的1080p (1920 x 1080) 高清图像质量SONY 1/2.9 “ExmorTM” CMOS传感器，210万像素，支持FULL HD,可实现高画面质量和高灵敏度强大的变焦能力18倍光学变焦，优异的自动对焦性能，F1.6F2.7光圈视频输出像素 （H）×（V）：1920 × 1080,1280 × 720视频格式 1080p/30，1080p

2、/25，1080p/24，720p/60，720p/50，720p/30，720p/25，720p/24日/夜功能 （开，关，自动）球形隐私区域遮蔽多种白平衡模式画面特效（电子翻转，黑白，镜像，图像增强）标题显示（每行20个字符，最多11行）电子快门接口支持30芯的细同轴电缆（LVDS视频输出）以及36芯FFC扁平线接口（数字视频输出）软件协议支持SONY VISCA或者HITACHI命令接口基本功能：尺寸图：规格说明：CMOS图像传感器图像尺寸6.4mm Dia.(TYPE 1/2.9)有效像素2.48M (2000x1241)逐行扫描是输出点数/帧率1280Hx720V/24fps1280

3、Hx720V/25fps1280Hx720V/30fps1280Hx720V/50fps1280Hx720V/60fps 1920Hx1080V/24fps      1920Hx1080V/25fps 1920Hx1080V/30fps同步系统内置最低照度0.5 lx (F1.6，50 IRE，ICR关闭)，0.095 lx （F1.6，50 IRE，ICR打开）镜头光学倍数18X焦点距离4.7±5%84.6±5%mm视场角FOVD : WIDE 68.5º±5% TELE 4.2º±

4、;5%H : WIDE 54.8º±5% TELE 3.4º±5%V : WIDE 41º±5%   TELE 2.5º±5%光圈值F NoF1.6F2.7对焦自动是手动是IR-cut自动是手动（开/关）是AGC控制自动是手动是功能左右镜像是上下颠倒是图像冻结否图像颠倒（270度）是隐私遮挡是数字宽动态否光圈手动/自动是背光补偿手动/自动是白平衡手动/自动是曝光手动/自动是电源输入电压9-12V DC电流（正常运行12v）240mA电流（Zoom Focus马达运转12v）300mA功耗3.6

5、W （马达启动），2.8W （马达不启动）输出视频（数字）视频输出制式BT1120或者LVDS（Y: 8比特，C：8比特，垂直同步，水平同步，场，时钟）720P/24 720P/25 720P/30 720P/50 720P/60 1080P/24 1080P/25 1080P/30摄像机组件控制接口SONY VISCA(信号电平3.3V)，波特率：9.6 Kb/s，19.2 Kb/s，38.4 Kb/s停止位：1/2位可选HITACHI COMMAND(信号电平3.3V)，波特率：4.8Kb/s，9.6 Kb/s，19.2 Kb/s，38.4 Kb/s，57.6Kb/s 停止位：1位尺寸84

6、x45x55mm连接座数量2（36Pin FPC/30Pin micro coaxial）建议使用的照度范围100 到100,000 lux存放温度-20至60工作温度-5至60存放湿度20%至95%操作湿度20%至80%重量约260g36Pin FPC 说明：引脚名称说明1RXD232BMCU2 串口2 RXD，CMOS 3.3V (低: 最高 0.8V, 高: 最低 2.8V) 2TDX232BMCU2 串口2 TXD，CMOS 3.3V (低: 最高 0.8V, 高: 最低 2.8V)3GND4DC IN912V 输入5DC IN912V 输入6DC IN912V 输入7GND8GND9

7、GND10GND11GND12CLKYC视频时钟输出13GND14HSYNC视频行控制信号输出15VSYNC视频场控制信号输出16GND17C7C输出，默认高位（寄存器可配置为低位或Y信号输出）18C6C输出19C5C输出20C4C输出21GND22C3C输出23C2C输出24C1C输出25C0C输出，默认低位（寄存器可配置为高位或Y信号输出）26GND27Y7Y输出，默认高位（寄存器可配置为低位或C信号输出）28Y6Y输出29Y5Y输出30Y4Y输出31GND32Y3Y输出33Y2Y输出34Y1Y输出35Y0Y输出，默认低位（寄存器可配置为高位或C信号输出）36GND30Pin 同轴线说明：

8、引脚名称说明1NC2NC3NC4NC5RST_N复位，低电平有效6NC7GND8GND9GND10GND11GND12GND13DC IN912V 输入14DC IN912V 输入15DC IN912V 输入16DC IN912V 输入17DC IN912V 输入18RXD232BMCU2 串口2 RXD，CMOS 3.3V (低: 最高 0.8V, 高: 最低 2.8V)19TXD232BMCU2 串口2 TXD，CMOS 3.3V (低: 最高 0.8V, 高: 最低 2.8V)20GND21TXIN0-LVDS输出22TXIN0+LVDS输出23TXIN1-LVDS输出24TXIN1+L

9、VDS输出25TXIN2-LVDS输出26TXIN0+LVDS输出27TXCLK-LVDS输出，时钟28TXCLK+LVDS输出，时钟29TXIN3-LVDS输出30TXIN3+LVDS输出控制板程序烧录说明：初次烧录程序时请按一次控制板底面KEY1按键，此时板正面Led1灯常亮，进入烧录态。命令列表：Ø Function Command ListCommand SetCommandCommand PacketCommentsNetwork ChangeBroadcast88 30 0x FFIF_ClearBroadcast88 01 00 01 FFCAM_Power On 8x

10、 01 04 00 02 FF Power ON/OFFOff 8x 01 04 00 03 FF CAM_Zoom Stop 8x 01 04 07 00 FFTele(Standard)8x 01 04 07 02 FFWide(standard)8x 01 04 07 03 FFTide(Variable)8x 01 04 07 2p FFp=0(low) to 7(High)Wide(Variable)8x 01 04 07 3p FFDirect 8x 01 04 47 0p 0q 0r 0s FFpqrs: Zoom PositionCAM_DZoomOn 8x 01 04 06

11、02 FF Digital zoom ON/OFF Off 8x 01 04 06 03 FF Combine Mode 8x 01 04 36 00 FF Optical/Digital Zoom Combined Separate Mode 8x 01 04 36 01 FF Optical/Digital Zoom Separate Stop 8x 01 04 06 00 FF Tele(Variable) 8x 01 04 06 2p FF p=0 (Low) to 7 (High) Wide(Variable) 8x 01 04 06 3p FF Direct 8x 01 04 46

12、 00 00 0p 0q FF pq: D-Zoom Position CAM_FocusStop8x 01 04 08 00 FFFar(Standard)8x 01 04 08 02 FFNear(Standard)8x 01 04 08 03 FFFar(Variable)8x 01 04 08 2p FFp=0(low) to 7(High)Near(Variable)8x 01 04 08 3p FFDirect8x 01 04 48 0p 0q 0r 0s FFpqrs: Focus PositionAuto Focus8x 01 04 38 02 FFAF ON/OFFManua

13、l Focus8x 01 04 38 03 FFAuto/ Manual8x 01 04 38 10 FFOne Push Trigger8x 01 04 18 01 FFInfinity8x 01 04 18 02 FFNear Limit8x 01 04 28 0p 0q 0s FFpqrs: Focus Near Limit PositionAF SensitivityNormal8x 01 04 58 02 FFAF Sensitivity High/LowLow8x 01 04 58 03 FFCAM_AF ModeNormal AF8x 01 04 57 00 FFAF Movem

14、ent ModeInterval AF8x 01 04 57 01 FFZoomTriggerAF8x 01 04 57 02 FFActive/Interval Time8x 01 04 27 0p 0q 0r 0s FFpq:Movement Time, rs:IntervalCAM_Zoom FocusDirect8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FFpqrs: Zoom Positiontuvw: Focus PositionCAM_InitializeLens8x 01 04 19 01 FFLens Initialization startCA

15、M_WBAuto8x 01 04 35 00 FFNormal AutoIndoor8x 01 04 35 01 FFIndoor modeOutdoor8x 01 04 35 02 FFOutdoor modeATW8x 01 04 35 04 FFAuto Manual8x 01 04 35 05 FFManual Control modeCAM_R GainReset8x 01 04 03 00 FFManual Control of R GainUp8x 01 04 03 02 FFDown8x 01 04 03 03 FFDirect8x 01 04 43 00 00 0p 0q F

16、Fpq: R GainCAM_B GainReset8x 01 04 04 00 FFManual Control of B GainUp8x 01 04 04 02 FFDown8x 01 04 04 03 FFDirect8x 01 04 44 00 00 0p 0q FFpq: B GainCAM_AEFull Auto8x 01 04 39 00 FFAutomatic Exposure modeManual8x 01 04 39 03 FFManual Control modeCAM_Shutter Reset 8x 01 04 0A 00 FF Shutter Setting Up

17、 8x 01 04 0A 02 FF Down 8x 01 04 0A 03 FF Direct 8x 01 04 4A 00 00 0p 0q FF pq: Shutter Position CAM_GainReset8x 01 04 0C 00 FFGain SettingUp8x 01 04 0C 02 FFDown8x 01 04 0C 03 FFDirect8x 01 04 4C 00 00 0p 0q FFpq: Gain PositionCAM_BacklightOn8x 01 04 33 02 FFBack LightCompensation ON/OFFOff8x 01 04

18、 33 03 FFCAM_LR_ReverseOn8x 01 04 61 02 FFMirror Image ON/OFFOff8x 01 04 61 03 FFCAM_FreezeOn8x 01 04 62 02 FFStill Image ON/OFFOff8x 01 04 62 03 FFCAM_PictureEffectOff8x 01 04 63 00 FFPicture Effect SettingNeg.Art8x 01 04 63 02 FFB&W8x 01 04 63 04 FFCAM_Picture FlipOn8x 01 04 66 02 FFPicture Fl

19、ip ON/OFFOff8x 01 04 66 03 FFCAM_MemoryReset8x 01 04 3F 00 0p FFp: Memory Number (=0 to 5)Set8x 01 04 3F 01 0p FFRecall8x 01 04 3F 02 0p FFCAM_CUSTOM Reset 8x 01 04 3F 00 7F FF Starts in this mode at Power ON.Set 8x 01 04 3F 01 7F FF Recall 8x 01 04 3F 02 7F FF CAM_MemSave Write 8x 01 04 23 0X 0p 0p

20、 0q 0q FF X: 00 to 07 (Address) Total 16 Byte ppqq: 0x0000 to 0xFFFF (Data) CAM_DisplayOn8x 01 04 15 02 FFDisplay: ON/OFFOff8x 01 04 15 03 FFOn/Off8x 01 04 15 10 FFCAM_TitleTitle Set18x 01 04 73 00 mm nn pp qq 00 00 00 00 00 00 FFmm:Vposition, nn:Hposition,pp:Color, qq:BlinkTitle Set28x 01 04 73 01

21、mm nn pp qq rr ss tt uu vv ww FFmnpqrstuvw:Setting of Display Characters (1st to 10st Character )Title Set38x 01 04 73 02 mm nn pp qq rr ss tt uu vv ww FFmnpqrstuvw: Setting of Display Characters (11 st to 20st Character )Title Clear8x 01 04 74 00 FFTitle Setting ClearOn8x 01 04 74 02 FFTitle Displa

22、y ON/OFFOff8x 01 04 74 03 FFCAM_MuteOn 8x 01 04 75 02 FF Mute ON/OFFOff 8x 01 04 75 03 FF On/Off 8x 01 04 75 10 FF CAM_ID Write8x 01 04 22 0p 0q 0r 0s FFpqrs: Camera ID (=0000 to FFFF)Ø Inquiry Command ListInquiry CommandCommand PacketInquiry PacketCommentsCAM_PowerInq8x 09 04 00 FFy0 50 02 FFO

23、ny0 50 03 FFOffCAM_ZoomPosInq8x 09 04 47 FFy0 50 0p 0q 0r 0s FFpqrs:ZoomPositionCAM_DZoomModeInq 8x 09 04 06 FF y0 50 02 FF D-Zoom On y0 50 03 FF D-Zoom Off CAM_DZoomC/SModeInq 8x 09 04 36 FF y0 50 00 FF Combine Mode y0 50 01 FF Separate Mode CAM_DZoomPosInq 8x 09 04 46 FF y0 50 00 00 0p 0q FF pq: D

24、-Zoom Position CAM_FocusModeInq8x 09 04 38 FFy0 50 02 FFAuto Focusy0 50 03 FFManual CAM_FocusPosInq8x 09 04 48 FFy0 50 0p 0q 0r 0s FFpqrs:FocusPositionCAM_FocusNear LimitInq8x 09 04 28 FFy0 50 0p 0q 0r 0s FFpqrs: Focus Near Limit PositionCAM_AFModeInq8x 09 04 57 FFy0 50 00 FFNormal AFy0 50 01 FFInte

25、rval AFy0 50 02 FFZoom Trigger AFCAM_AFTime SettingInq8x 09 04 27 FFy0 50 0p 0q 0r 0s FFpq: Movement Time, rs: IntervalCAM_WBModeInq8x 09 04 35 FFy0 50 00 FFAutoy0 50 01 FFIn Doory0 50 02 FFOut Doory0 50 05 FFManualCAM_RGainInq8x 09 04 43 FFy0 50 00 00 0p 0q FFpq: R GainCAM_BGainInq8x 09 04 44 FFy0

26、50 00 00 0p 0q FFpq: B GainCAM_AEModeInq8x 09 04 39 FFy0 50 00 FFFull Autoy0 50 03 FFManualy0 50 0B FFIris PriorityCAM_IrisPosInq8x 09 04 4B FFy0 50 00 00 0p 0q FFpq: Iris PriorityCAM_GainPosInq8x 09 04 4C FFy0 50 00 00 0p 0q FFpq: Gain PriorityCAM_BacklightModeInq8x 09 04 33 FFy0 50 02 FFOny0 50 03

27、 FFOffCAM_LR_ReverseModeInq8x 09 04 61 FFy0 50 02 FFOny0 50 03 FFOffCAM_FreezeModeInq8x 09 04 62 FFy0 50 02 FFOny0 50 03 FFOffCAM_PictureEffectModeInq8x 09 04 63 FFy0 50 00 FFOffy0 50 02 FFNeg.Arty0 50 04 FFB&WCAM_PictureFlipModeInq8x 09 04 66 FFy0 50 02 FFOny0 50 03 FFOffCAM_MemoryInq8x 09 04 3F FFy0 50 pp FFpp: Last Recall Memory No.CAM_MemSaveInq8x 09 04 23 0x FFy0 50 0p 0p 0q 0q FFX:0007(Address) ppqq: 0x0000 to 0xFFFF (Data)CAM_DisplayModeInq8x 09 04 15 FFy0 50 02 FFOny0 5