最新10月CCNA题库word版1100题

1、question 1when you are logged into a switch, which prompt indicates that you are in privileged mode?a. %b. c. >d. $e. #question 2which command shows system hardware and software version information?a. show configurationb. show environmentc. show inventoryd. show platforme. show versionquestion 3c

2、isco catalyst switches cat1 and cat2 have a connection between them using ports fa0/13. an 802. 1qtrunk is configured between the two switches. on cat1, vlan 10 is chosen as native, but on cat2 thenative vlan is not specified.what will happen in this scenario?a. 802.1q giants frames could saturate t

3、he link.b. vlan 10 on cat1 and vlan 1 on cat2 will send untagged frames.c. a native vlan mismatch error message will appear.d. vlan 10 on cat1 and vlan 1 on cat2 will send tagged frames.question 4which command would correctly configure a serial port on a router with the last usable host address in t

4、he2/29 subnet?a. router(config-if)# ip address 8 40b. router(config-if)# ip address 9 24c. router(config-if)# ip address 3 48d. router(config-if)# ip address 9 48e. router(config-if)# ip a

5、ddress 3 48f. router(config-if)# ip address 8 48question 5the network default gateway applying to a host by dhcp is 3/28. which option is the valid ipaddress of this host?a. 5b. 7c. 0d. 2e. 192.1

6、68.5.14question 6which two addresses can be assigned to a host with a subnet mask of ? (choose two.)a. b. c. 55d. 55e. question 7the network administrator has asked you to check the status of the workstation's ip stack by pinging thel

7、oopback address. which address would you ping to perform this task?a. b. c. d. question 8workstation a has been assigned an ip address of 4/28. workstation b has been assigned an ipaddress of 00/28. the two workstations are connected with a stra

8、ight-through cable. attempts toping between the hosts are unsuccessful. what two things can be done to allow communications betweenthe hosts? (choose two.)a. replace the straight-through cable with a crossover cable.b. change the subnet mask of the hosts to /25.c. change the subnet mask of the hosts

9、 to /26.d. change the address of workstation a to 5.e. change the address of workstation b to 11.question 9your isp has given you the address /29 to assign to your router's interface. they have alsogiven you the default gateway address of . after you have co

10、nfigured the address, the router isunable to ping any remote devices. what is preventing the router from pinging remote devices?a. the default gateway is not an address on this subnet.b. the default gateway is the broadcast address for this subnet.c. the ip address is the broadcast address for this

11、subnet.d. the ip address is an invalid class d multicast address.question 10which command is used to copy the configuration from ram into nvram?a. copy running-config startup-configb. copy startup-config: running-config:c. copy running config startup configd. copy startup config running confige. wri

12、te terminalquestion 11which command is used to load a configuration from a tftp server and merge the configuration intoram?a. copy running-config: tftp:b. copy tftp: running-configc. copy tftp: startup-configd. copy startup-config: tftp:question 12a system administrator types the command to change t

13、he hostname of a router. where on the cisco ifs isthat change stored?a. nvramb. ramc. flashd. rome. pcmciaquestion 13which command is used to configure a default route?a. ip route b. ip route c. ip route 172.16.

14、2.1d. ip route question 14if ip routing is enabled, which two commands set the gateway of last resort to the default gateway?(choose two.)a. ip default-gateway b. ip route c. ip default-network d. ip default-route 172.

15、16.2.1e. ip route question 15which command would you configure globally on a cisco router that would allow you to view directlyconnected cisco devices?a. enable cdpb. cdp enablec. cdp rund. run cdpquestion 16which command is used to see the path taken by packets across an i

16、p network?a. show ip routeb. show routec. tracerouted. trace ip routequestion 17which command is used to debug a ping command?a. debug icmpb. debug ip icmpc. debug tcpd. debug packetquestion 18which command displays cpu utilization?a. show protocolsb. show processc. show systemd. show versionquestio

17、n 19when configuring a serial interface on a router, what is the default encapsulation?a. atm-dxib. frame-relayc. hdlcd. lapbe. pppquestion 20what must be set correctly when configuring a serial interface so that higher-level protocols calculate thebest route?a. bandwidthb. delayc. loadd. reliabilit

18、yquestion 21a company implements video conferencing over ip on their ethernet lan. the users notice that thenetwork slows down, and the video either stutters or fails completely. what is the most likely reason forthis?a. minimum cell rate (mcr)b. quality of service (qos)c. modulationd. packet switch

19、ing exchange (pse)e. reliable transport protocol (rtp)question 22which layer in the osi reference model is responsible for determining the availability of the receivingprogram and checking to see if enough resources exist for that communication?a. transportb. networkc. presentationd. sessione. appli

20、cationquestion 23data transfer is slow between the source and destination. the quality of service requested by the transportlayer in the osi reference model is not being maintained. to fix this issue, at which layer should thetroubleshooting process begin?a. presentationb. sessionc. transportd. netw

21、orke. physicalquestion 24which protocols are found in the network layer of the osi reference model and are responsible for pathdetermination and traffic switching?a. lanb. routingc. wand. networkquestion 25which command reveals the last method used to powercycle a router?a. show reloadb. show bootc.

22、 show running-configd. show versionquestion 26which three options are valid wan connectivity methods? (choose three.)a. pppb. wapc. hdlcd. mplse. l2tpv3ccna考试报名1700元 7f. atmquestion 27refer to the exhibit. which wan protocol is being used?a. atmb. hdlcc. frame relayd. pppquestion 28what is the diffe

23、rence between a csu/dsu and a modem?a. a csu/dsu converts analog signals from a router to a leased line; a modem converts analog signalsfrom a router to a leased line.b. a csu/dsu converts analog signals from a router to a phone line; a modem converts digital signalsfrom a router to a leased line.c.

24、 a csu/dsu converts digital signals from a router to a phone line; a modem converts analog signalsfrom a router to a phone line.d. a csu/dsu converts digital signals from a router to a leased line; a modem converts digital signalsfrom a router to a phone line.question 29a network administrator must

25、configure 200 switch ports to accept traffic from only the currently attachedccna考试报名1700元 8host devices. what would be the most efficient way to configure mac-level security on all these ports?a. visually verify the mac addresses and then telnet to the switches to enter the switchport-port security

26、mac-address command.b. have end users e-mail their mac addresses. telnet to the switch to enter the switchport-port securitymac-address command.c. use the switchport port-security mac address sticky command on all the switch ports that have enddevices connected to them.d. use show mac-address-table

27、to determine the addresses that are associated with each port and thenenter the commands on each switch for mac address port-security.question 30when troubleshooting a frame relay connection, what is the first step when performing a loopback test?a. set the encapsulation of the interface to hdlc.b.

28、place the csu/dsu in local-loop mode.c. enable local-loop mode on the dce frame relay router.d. verify that the encapsulation is set to frame relay.what occurs on a frame relay network when the cir is exceeded?a. all tcp traffic is marked discard eligible.b. all udp traffic is marked discard eligibl

29、e and a becn is sent.c. all tcp traffic is marked discard eligible and a becn is sent.d. all traffic exceeding the cir is marked discard eligible.question 32what are two characteristics of frame relay point-to-point subinterfaces? (choose two.)a. they create split-horizon issues.b. they require a un

30、ique subnet within a routing domain.c. they emulate leased lines.d. they are ideal for full-mesh topologies.e. they require the use of nbma options when using ospf.question 33refer to the exhibit. addresses within the range /24 are not being translated to the 1.128.0/16range. which command

31、 shows if /24 are allowed inside addresses?a. debug ip natb. show access-listc. show ip nat translationd. show ip nat statisticsquestion 34a wireless client cannot connect to an 802.11b/g bss with a b/g wireless card. the client section of theaccess point does not list any active wlan clie

32、nts. what is a possible reason for this?a. the incorrect channel is configured on the client.b. the client's ip address is on the wrong subnet.c. the client has an incorrect pre-shared key.d. the ssid is configured incorrectly on the client.question 35which two features did wpav1 add to address

33、the inherent weaknesses found in wep? (choose two.)ccna考试报名1700元 10艾迪飞论坛 艾迪飞论坛 a. a stronger encryption algorithmb. key mixing using temporal keysc. shared key authenticationd. a shorter initialization vectore. per frame sequence countersquestion 36which two wireless encryption methods are based on

34、the rc4 encryption algorithm? (choose two.)a. wepb. cckmc. aesd. tkipe. ccmpquestion 37what are two characteristics of ripv2? (choose two.)a. classful routing protocolb. variable-length subnet masksc. broadcast addressingd. manual route summarizatione. uses spf algorithm to compute pathquestion 38wh

35、ich two ethernet fiber-optic modes support distances of greater than 550 meters?a. 1000base-cxccna考试报名1700元 11艾迪飞论坛 艾迪飞论坛 艾迪飞论坛 b. 100base-fxc. 1000base-lxd. 1000base-sxe. 1000base-zxquestion 39what two things will a router do when running a distance vector routing protocol? (choose two.)a. send per

36、iodic updates regardless of topology changes.b. send entire routing table to all routers in the routing domain.c. use the shortest-path algorithm to the determine best path.d. update the routing table based on updates from their neighbors.e. maintain the topology of the entire network in its databas

37、e.question 40refer to the exhibit. according to the routing table, where will the router send a packet destined for5?a. b. c. d. question 41which command shows if an access list is assigned to an interface?a. show ip interface interface access-listsb. show ip

38、access-lists interface interfacec. show ip interface interfaced. show ip access-lists interfacequestion 42refer to the exhibit. which rule does the dhcp server use when there is an ip address conflict?a. the address is removed from the pool until the conflict is resolved.b. the address remains in th

39、e pool until the conflict is resolved.c. only the ip detected by gratuitous arp is removed from the pool.d. only the ip detected by ping is removed from the pool.e. the ip will be shown, even after the conflict is resolved.question 43refer to the exhibit. you are connected to the router as user mike

40、. which command allows you to seeoutput from the ospf debug command?a. terminal monitorb. show debuggingc. show sessionsd. show ip ospf interfacequestion 44refer to the exhibit. if number 2 is selected from the setup script, what happens when the user runs setupfrom a privileged prompt?a. setup is a

41、dditive and any changes will be added to the config script.b. setup effectively starts the configuration over as if the router was booted for the first time.c. setup will not run if an enable secret password exists on the router.d. setup will not run, because it is only viable when no configuration

42、exists on the router.question 45refer to the exhibit. which (config-router) command will allow the network represented on the interface tobe advertised by rip?a. redistribute ethernet0b. network ethernet0ccna考试报名1700元 14艾迪飞论坛 艾迪飞论坛 c. redistribute d. network question 46refer to the

43、 exhibit. what information can be gathered from the output?a. one router is running ripv1.b. rip neighbor is .c. the network contains a loop.d. network is reachable.question 47refer to the exhibit. what type of connection would be supported by the cable diagram shown?a. pc to rout

44、erb. pc to switchc. server to routerd. router to routerquestion 48refer to the exhibit. what type of connection would be supported by the cable diagram shown?a. pc to routerb. pc to switchc. server to switchd. switch to routerquestion 49which two statements describe the cisco implementation of vlans

45、? (choose two.)a. vlan 1 is the default ethernet vlan.b. cdp advertisements are only sent on vlan 1002.c. by default, the management vlan is vlan 1005.d. by default, the switch ip address is in vlan 1005.e. vlan 1002 through 1005 are automatically created and cannot be deleted.question 50refer to th

46、e exhibit. what can be determined about the router from the console output?a. no configuration file was found in nvram.b. no configuration file was found in flash.c. no configuration file was found in the pcmcia card.d. configuration file is normal and will load in 15 seconds.question 52refer to the

47、 exhibit. which command would allow the translations to be created on the router?a. ip nat pool mynats 54 prefix-length 19b. ip nat outside mynats 54 prefix-length 19c. ip nat pool mynats 54 prefix-length 18d. ip nat outside mynats 1

48、.1.135.254 prefix-length 18question 53refer to the exhibit. an administrator pings the default gateway at and sees the output asshown. at which osi layer is the problem?a. data link layerb. application layerc. access layerd. session layere. network layerquestion 54refer to the exhibit. wh

49、ich value will be configured for default gateway of the local area connection?a. b. 54c. d. 54question 55refer to the exhibit. the user at workstation b reports that server a cannot be reached. what ispreventing workstation b from reaching server a?a. the ip

50、 address for server a is a broadcast address.b. the ip address for workstation b is a subnet address.c. the gateway for workstation b is not on the same subnet.d. the gateway for server a is not on the same subnet.question 56refer to the exhibit. what does the (*) represent in the output?a. packet i

51、s destined for a local interface to the router.b. packet was translated, but no response was received from the distant device.c. packet was not translated, because no additional ports are available.d. packet was translated and fast switched to the destination.question 57refer to the exhibit. what co

52、mmand sequence will enable pat from the inside to outside network?a. (config) ip nat pool isp-net netmask overloadb. (config-if) ip nat outside overloadc. (config) ip nat inside source list 1 interface ethernet1 overloadd. (config-if) ip nat inside overloadquestion 58refer to t

53、he exhibit. what will happen to http traffic coming from the internet that is destined for0 if the traffic is processed by this acl?a. traffic will be dropped per line 30 of the acl.b. traffic will be accepted per line 40 of the acl.c. traffic will be dropped, because of the implicit deny

54、 all at the end of the acl.d. traffic will be accepted, because the source address is not covered by the acl.question 59refer to the exhibit. which statement describes the effect that the router1 configuration has on devices inthe subnet when they try to connect to svr-a using telnet or

55、ssh?a. devices will not be able to use telnet or ssh.b. devices will be able to use ssh, but not telnet.c. devices will be able to use telnet, but not ssh.d. devices will be able to use telnet and ssh.question 60what are three advantages of vlans? (choose three.)a. vlans establish broadcast domains in switched networks.b. vlans utilize packet filtering to enhance network security.c. vlans provide a method of conserving ip addresses in large networks.d. vlans provide a low-latency internetworking alternative to routed networks.e. vlans allow access to network serv